• Journal of the korean academy of Pediatric Dentistry
• /
• v.37 no.4
• /
• pp.422-428
• /
• 2010

Giomer is fluoride-releasing, resin-based dental materials that comprise PRG(pre-reacted glass ionomer) filler. The purpose of this study was to evaluate the shear bond strength of Giomer using self-etching primer systems to bovine dentin. Bovine incisors were mounted in self-curing orthodontic resin and the facial surfaces were wet ground on SIC paper to expose the dentin. Total 100 samples were made and divided randomly into 4 groups, Giomer group(I), Composite resin group(II) and Compomer group(III), Giomer and single bottle adhesive group(IV). The shear bond strengths of 25 samples per each group were measured using universal testing machine. And data were analyzed statistically with One-way ANOVA and Scheffe test. Giomer group(I) showed the significantly higher bond strength than Compomer group(III)(p<0.05). There was no significant difference between Giomer group(I) and Composite resin group(II)(p>0.05). And there is no significant difference between gourp(I) and group(IV). Based on the results of present study, the use of Giomer as an esthetic restorative material for primary teeth might be justified. It is considered that more study about the fluoride releasing ability is needed to evaluate the anticariogenic effect of giomer.

• Proceedings of the KIEE Conference
• /
• 2008.05a
• /
• pp.187-188
• /
• 2008

In this paper, we have investigated water content of semiconductive shield materials for power cables, EEA(Ethylene Ethyl Acrylate) is used polymer matrix. And filler is used CNT(Carbon Nanotube) and CB(Carbon Black). EEA, CNT and CB is favor moisture. In case of EEA, it has polyolefin resin that strong polarity combination. To research water content, experimental method used KF(Karl Fischer). KF method is Electrochemical titration based on chemical reaction. As a result, specification by KEPCO(Korea Electric Power Corporation) is lower than 800ppm. CNT and CB ratio of 80 versus 20 is best specimen that had lowest moisture content. It seem likely to increase crosslinking rate, CNT between CB.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.11
• /
• pp.1463-1470
• /
• 2018

In this study, 20 types of samples were prepared by mixing different kinds of inorganic materials to develop insulation materials for epoxy - based GIS substation equipment used under high voltage environmentally friendly insulation gas. One of the electrical characteristics, AC insulation breakdown experiment was performed. As mixing ratio of mixed heterogeneous inorganic materials, the dielectric breakdown strength was increased with increasing filler ratio of micro silica, micro silica : micro Alumina, 1:9, 3:7, 5:5, 7:3, 9:1, and decreased as the filling amount of micro alumina increased. The AC insulation breakdown characteristics were the best when the composition ratio was 9:1. The higher the content of silica, the better the interfacial properties, and the larger the alumina content ratio, the worse the interfacial properties.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.68-70
• /
• 2002

Prediction of 3-D permeability tensor for multi-axial preform is critical to model and design the manufacturing process of composites by considering resin flow through the multi-axial fiber structure. In this study, the in-plane and transverse permeabilities for braided preform are predicted numerically. The flow analyses are calculated by using 3-D CVFEM(control volume finite element method) for macro-unit cells. To avoid checker-board pressure field and improve the efficiency of numerical computation, a new interpolation function for velocity is proposed on the basis of analytic solutions. Permeability of a braided preform is measured through unidirectional flow experiment and compared with the permeability calculated numerically. Unlike other studies, the current study is based on more realistic unit cell and prediction of permeability is improved.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.04a
• /
• pp.188-191
• /
• 2003

In this wort. the effect of anodic oxidation on surface characteristics of high strength PAN-based carbon fibers is investigated in terms of surface and mechanical interfacial properties of the composites. As a result, the acidity of carbon fiber surfaces is increased, due to the development of oxygen functional groups in the presence of anodic oxidation. Also. it is found that the critical stress intensity factor ($K_{IC}$) is improved in the oxidized fibers-reinforced composites. which can be attributed to the good wettability between fibers and epoxy resin matrix.

• Steel and Composite Structures
• /
• v.33 no.2
• /
• pp.299-306
• /
• 2019

The natural fibre composites are termed as bio-composites. They have shown a promising replacement to the current carbon/glass fibre reinforced composites as environmental friendly materials in specific applications. Natural fibre reinforced composites are potential materials for various engineering applications in automobile, railways, building and Aerospace industry. The natural fibre selected to fabricate the composite material is plant-based fibre e.g., sisal fibre. Sisal fibre is a suitable reinforcement for use in composites on account of its low density, high specific strength, and high hardness. Epoxy is a thermosetting polymer which is used as a resin in natural fibre reinforced composites. Hand lay-up technique was used to fabricate the composites by reinforcing sisal fibres into the epoxy matrix. Composites were prepared with the unidirectional alignment of sisal fibres. Test specimens with different fibre orientations were prepared. The fabricated composites were tested for mechanical properties. Impact test, tensile test, flexural test, hardness test, compression test, and thermal test of composites had been conducted to assess its suitability in industrial applications. Scanning electron microscopy (SEM) test revealed the microstructural information of the fractured surface of composites.

• Design & Manufacturing
• /
• v.15 no.2
• /
• pp.1-10
• /
• 2021

In this study, the current state of the plastics industry has been examined. The direction of development and innovation is reviewed and commented. The technical statuses of various sectors such as thermoplastic resin, composite material, mold engineering, and simulation have been scrutinized. In addition, the industrial status of each sector has been reviewed. Then, the challenges that the plastics manufacturing industry has to deal with have been discussed. Especially, the situation in Republic of Korea has been elaborated in detail. Based on the discussion, an open innovation strategy has been suggested. It has been argued in this work that the open innovation strategy will enables efficient funding and development by avoiding resource consuming rent seeking.

• Composites Research
• /
• v.35 no.6
• /
• pp.394-401
• /
• 2022

Two polymer precursors, polyvinylidene chloride-resin (PVDC-resin) and polyvinylidene fluoride (PVDF), are assembled into the microporous carbon by pyrolysis. Microporous carbon is advantageous as an electrode for supercapacitors that store electric charges through ion adsorption/desorption. The pyrolysis also turns the various heteroatoms of two precursors into functional groups, contributing to the additional charge storage. The analysis of the porous structure and function group during carbonization are important to develop the carbon for energy storage. Here, we analyzed the functional groups of two polymer-derived carbons through X-ray photoelectron spectroscopy. The electrochemical properties of the functional groups were explored in various pH electrolytes. The specific capacitance of two carbons in the acidic electrolyte (1 M H₂SO₄) was improved compared to that in the neutral electrolyte (0.5 M Na₂SO₄) due to the faradaic charge/discharge reaction of the quinone functional group. In particular, the carbon electrode derived from PVDC-resin exhibits a lower capacity than the carbon from PVDF due to the small micropores. In the alkaline electrolyte (6 M KOH), the highest specific capacitance and rate capability were obtained among the three electrolytes for both electrodes based on the facile adsorption of the constituent electrolyte ions (K⁺, OH^-).

• The Journal of Advanced Prosthodontics
• /
• v.8 no.2
• /
• pp.94-100
• /
• 2016

PURPOSE. To evaluate the effects of hydrogen peroxide pretreatment and heat activation of silane on the shear bond strength of fiber-reinforced composite posts to resin cement. MATERIALS AND METHODS. The specimens were prepared to evaluate the bond strength of epoxy resin-based fiber posts (D.T. Light-Post) to dual-curing resin cement (RelyX U200). The specimens were divided into four groups (n=18) according to different surface treatments: group 1, no treatment; group 2, silanization; group 3, silanization after hydrogen peroxide etching; group 4, silanization with warm drying at $80^{\circ}C$ after hydrogen peroxide etching. After storage of the specimens in distilled water at $37^{\circ}C$ for 24 hours, the shear bond strength (in MPa) between the fiber post and resin cement was measured using a universal testing machine. The fractured surface of the fiber post was examined using scanning electron microscopy. Data were analyzed using one-way ANOVA and post-hoc analysis with Tukey's HSD test (${\alpha}=0.05$). RESULTS. Silanization of the fiber post (Group 2) significantly increased the bond strength in comparison with the non treated control (Group 1) (P<.05). Heat drying after silanization also significantly increased the bond strength (Group 3 and 4) (P<.05). However, no effect was determined for hydrogen peroxide etching before applying silane agent (Group 2 and 3) (P>.05). CONCLUSION. Fiber post silanization and subsequent heat treatment ($80^{\circ}C$) with warm air blower can be beneficial in clinical post cementation. However, hydrogen peroxide etching prior to silanization was not effective in this study.

• Composites Research
• /
• v.30 no.5
• /
• pp.261-266
• /
• 2017

Polymer composites are materials in which various fillers are uniformly dispersed on the basis of organic resin. They have excellent processability and diversity for industrial products. Recently, as carbon nanomaterials are developed, there is a great deal of effort to use them as reinforcing fillers to fabricate high performance composite materials. In order to transfer the inherent properties of fillers into composite materials as much as possible, the good dispersion and orientation of fillers, and favorable interfacial interaction between fillers and matrix are considered to be very important. In this review article, we intent to derive and explain the relationship between surface chemical structure of fillers and physical properties of composites as a strategy of high strength and toughness of graphenebased polyimide composites.