• ETRI Journal
• /
• 제27권3호
• /
• pp.257-266
• /
• 2005

Many multi-modulus blind equalization algorithms (MMA) have been presented in the past to overcome the undesirable high misadjustment exhibited by the well-known constant modulus algorithm. Some of these MMA schemes, specifically tailored for quadrature amplitude modulation (QAM) constellations, have also been proved to fix the phase offset error without needing any rotator at the end of the equalizer stage. In this paper, a new multi-modulus algorithm is presented for QAM signals. The contribution lies in the technique to incorporate the sliced symbols (outcomes of decision device) in the multi-modulus-based weight adaptation process. The convergence characteristics of the proposed sliced multi-modulus algorithm (S-MMA) is demonstrated by way of simulations, and it is shown that it gives better steady-state performance in terms of residual inter-symbol interference and symbol-error rate. It has also been shown that the proposed algorithm exhibits lesser steady-state misadjustment compared to the best reported MMA.

• 로봇학회논문지
• /
• 제12권3호
• /
• pp.258-262
• /
• 2017

In this paper, we propose a new collision detection algorithm for human-robot collaboration. We use an IMU sensor located at the tip of the manipulator and the kinematic behavior of the manipulator to detect the unexpected collision between the robotic manipulator and environment. Unlike other method, the developed algorithm uses only the kinematic relationship between the manipulator joint and the end effector. Therefore, the collision estimation signal is not affected by the error of the dynamics model. The proposed collision detection algorithm detects the collision by comparing the estimated acceleration of the end effector derived from the position, velocity and acceleration trajectories of the robot joints with the actual acceleration measured by the sensor. In simulation, we compare the performance of our method with the conventional Residual Observer (ROB). Our method is less sensitive to the load variation because of the independency on the dynamic modeling of the manipulator.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.38-40
• /
• 2008

This paper presents the torque ripple and vibration characteristic of interior type permanent magnet (IPM) motor according to rotor design. In the design methods, the optimal notchs are put on the rotor pole face, which have an effect on variation of permanent magnet (PM) shape or residual flux density of PM. Through the space harmonics field analysis, the positions of notch are found and the optimal shapes of notch are decided by using Finite Element Method (FEM). The validity of the proposed method is confirmed with experiments. Therefore, the vibration, starting current and efficiency of IPM is measured by experiment.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국제학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.496-500
• /
• 1993

This paper presents an end-point position control of 1-link flexible robot arm by the PID self-tuning fuzzy algorithm. The governing equation is derived by the extended Hamilton's principle and based on the Bernoullie-Euler beam theory. The governing equation is solved by applying the Laplace transform and the numerical inversion method. The arm is mounted on the translational mechanism driven by a ballscrew whose rotation is controlled by dcservomotor. Tip position is controlled by the PID self-tuning fuzzy algorithm so that it follows a desired position. This paper shows the experimental and theoretical results of tip dispalcement, and also shows the good effects reducing the residual vibration of the end-point.

• International Journal of Concrete Structures and Materials
• /
• 제6권3호
• /
• pp.155-163
• /
• 2012

In order to predict the neutralization of concrete which is the reaction of carbonation dioxide from the outside and cement hydration product, such as calcium hydroxide and C-S-H, it was studied the numerical analysis method considering change of the pore structure and relative humidity during the neutralization reaction. Diffusion-reaction neutralization model was developed to predict the neutralization depth of concrete with coating finishing material. In order to build numerical analysis models considering outdoor environment and finishing materials, the adaption of proposed model was shown the results of existing outdoor exposure test results and accelerated carbonation test.

• 동력기계공학회지
• /
• 제7권1호
• /
• pp.51-59
• /
• 2003

The recent amount of container freight continuously has been increased, but the low efficiency of container crane causes jamming frequently in transportation and cargo handling at port. It is required that the working velocity and safety are improved by control of moving the trolley as quick as possible without large overshoot and any residual swing motion of container at the destination. In this paper, a LQ Fuzzy controller for a container crane is proposed to accomplish an optimal design of improved control system for minimizing the swing motion at destination. In this scheme a mathematical model for the system is obtained in state space form. Finally, the effectiveness of the proposed controller is verified through computer simulation.

• 대한전기학회논문지
• /
• 제40권8호
• /
• pp.751-756
• /
• 1991

In this paper, three dimensional magnetostatic fields are analysed using tetrahedral edge elements, magnetic vector potential and modified formulation of weighted residual method. If we define unknown variables in mesh edges, some conditions, such as Coulomb gauge condition in magnetic vector potential are naturally satisfied. So with less memory space, we can obtain more accurate solutions than the method where unknown variables are defined at nodes. Reliability and utility of this method are verified in two examples.

• 한국결정학회지
• /
• 제11권4호
• /
• pp.231-237
• /
• 2000

CMR Materials RE/sub 1-x/Ca/sub x/MnO₃(RE=La, Nd, A=Ca, Sr) were grown using the floating zone image furnace with halogen lamps as heat source. The growth condition was at 2∼10 mm/hr growth rate in air atmosphere, were 445∼50 rpm and 20∼25 rpm of rotation rate of feedrod and growing crystal, respectively. The grown crystals showed shiny black color and annealed at 1500℃ in a box furnace to release the residual stress during cooling. Characterization analyses of the crystal were carried out using XRD and SEM. The crystal structure of Nd/sub 0.7/Ca/sub 0.3/MnO₃ was analyzed with smart CCD XRD was lattice parameter of a=5.425(4)Å, b=5.434(4)Å, and c=7.712(5)Å, an orthorombic system with space group of pbnm.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 추계학술대회 논문집 학회본부
• /
• pp.211-215
• /
• 1989

This paper presents the thermal analysis of EHV OF cable accessories using FEM. The governing equation about the temperature in the cable accessories is induced by the energy balance equation. Since the temperature distribution is a function of space and time, the weighted residual method is adopted for FEM formulation. The difference approximation is used to treat the time differential term in the element equation. Automatic mesh generation which save time and labor is introduced for the data input process. It will be expected that the following thermal analysis result will be very useful to cable accessories design.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.47-49
• /
• 2008

This paper presents the vibration characteristic of interior type permanent magnet (IPM) motor according to rotor design. In the design methods, the optimal notchs are put on the rotor pole face, which have an effect on variation of permanent magnet (PM) shape or residual flux density of PM. Through the space harmonics field analysis, the positions of notch are found and the optimal shapes of notch are decided by using Finite Element Method (FEM). The validity of the proposed method is confirmed with experiments. Therefore, the vibration, starting current and efficiency of IPM is measured by experiment.