• 한국세라믹학회지
• /
• 제50권3호
• /
• pp.218-225
• /
• 2013

The densification behavior and strength of sintered reaction bonded silicon nitrides (SRBSN) that contain $Lu_2O_3-SiO_2$ additives were improved by the addition of fine Si powder. Dense specimens (relative density: 99.5%) were obtained by gas-pressure sintering (GPS) at $1850^{\circ}C$ through the addition of fine Si. In contrast, the densification of conventional specimens did not complete at $1950^{\circ}C$. The fine Si decreased the onset temperature of shrinkage and increased the shrinkage rate because the additive helped the compaction of green bodies and induced the formation of fine $Si_3N_4$ particles after nitridation and sintering at and above $1600^{\circ}C$. The amount of residual $SiO_2$ within the specimens was not strongly affected by adding fine Si powder because most of the $SiO_2$ layer that had formed on the fine Si particles decomposed during nitridation. The maximum strength and fracture toughness of the specimens were 991 MPa and $8.0MPa{\cdot}m^{1/2}$, respectively.

• 대한치과보철학회지
• /
• 제54권2호
• /
• pp.146-151
• /
• 2016

상악 완전 무치악에 6개 이상의 임플란트가 식립된 경우 임플란트-지지형 피개의치 제작이 가능하다. 임플란트-지지 피개의치에 사용되는 다양한 부착장치 중에 milled-bar의 경우 의치의 회전을 허용하지 않고, 안정성이 뛰어나며, 여러 개의 임플란트를 연결 고정하는 효과를 가진다는 장점이 있다. 본 증례에서는 전치부에 심한 골소실을 동반한 상악 완전 무치악 환자에서 세 가지 다른 시스템으로 구성된 7개의 임플란트 상부에 CAD/CAM 맞춤형 지대주와 시멘트 접착형의 milled bar를 이용한 피개의치를 제작하여 상실된 심미와 기능을 효과적으로 회복하였다.

• 대한치과보철학회지
• /
• 제31권3호
• /
• pp.351-384
• /
• 1993

Complete denture occlusion must be developed to function efficiently and with the least amount of trauma to the supporting tissues. For the preservation of supporting tissues, it is imperative to reduce to a minimum the functional stress induced by dentures. The magnitude of the horizontal component of functional stress contributed by various occlusal teeth forms has not been studied. This study was aimed to investigate the influence of different occlusal teeth forms on the mode of distribution of the stresses in the mandibular tissue, and the displacement of lower dentures during the variant functional movement of mandible for this study three dimensional finite element analysis was used. FEM models were created using commercial software Super Sap for IBM 32 bit computer. The model was composed of 3380 brick elements and 4346 nodes. The results were as follows. 1. The magnitude of stress was similar between two models in centric occlusion, in the case of anatomic model, the stress was concentrated on the buccal side of alveolar ridge beneath the bicuspids. 2. During the protrusive movement, the increasing of stress from the posterior to anterior part of mandible was seen in the case of anatomic model. 3. During the lateral movement, the stress of anatomic model was greater than that of nonanatomic model. 4. The stress of anatomic model was concentrated on the anterior region of residual ridge during the lateral movement. 5. In the case of anatomic model the anterior part of denture was displaced severely at the centric and lateral position, but the denture of nonanatomic model was displaced minutely at the protrusive and lateral position.

• 대한치과보철학회지
• /
• 제47권2호
• /
• pp.206-214
• /
• 2009

연구목적: 하악 우측 제1, 2 대구치가 결손된 Kennedy 분류 II급 증례에서 임상적으로 적용할 수 있는 편측 유리단 가철성 국소의치의 종류에 따른 응력 분포 양상을 비교하는 것이다. 연구 재료 및 방법: Kennedy 분류 II급 증례의 광탄성 모형에서 클라스프를 이용한 국소의치, 코너스 치관을 이용한 국소의치, 완압형 어태치먼트를 이용한 국소의치, 탄성 레진을 이용한 국소의치를 편측성으로 제작하였다. 응력 동결로에서 응력 주기에 맞춰 각 국소의치의 제1 대구치 중심와에 6 kg의 수직하중을 가하면서 응력을 동결하였다. 광탄성 모형을 절단하여 만든 시편을 광탄성 실험 장치로 광탄성 등색선의 흑백 무늬를 관찰하고 디지털 카메라로 촬영하였다. 촬영된 사진에서 8개의 측정점을 정하여 육안으로 무늬차수를 계측하고 비교하였다. 결과: 각 절단 시편의 최대 무늬차수와 하중점 직하방의 잔존 치조제에 발생한 무늬차수는 탄성 레진을 이용한 국소의치, 클라스프를 이용한 국소의치, 완압형 어태치먼트를 이용한 국소의치, 코너스 치관을 이용한 국소의치 순으로 높게 관찰되었다. 제2 소구치 치근단에 발생한 무늬차수는 클라스프를 이용한 국소의치, 탄성 레진을 이용한 국소의치, 코너스 치관을 이용한 국소의치, 완압형 어태치먼트를 이용한 국소의치 순으로 높게 관찰되었다. 결론: 코너스 치관을 이용한 국소의치가 수직하중시 지대치 주위 치조골과 잔존 치조제에 대하여 응력을 가장 균형있게 분산시켰고, 탄성 레진을 이용한 국소의치는 지대치보다 잔존 치조제의 상태가 더 양호한 경우에 적용 가능할 것이다.

• 대한치과보철학회지
• /
• 제40권5호
• /
• pp.507-524
• /
• 2002

Load transfer of implant overdenture varies depending on anchorage systems that are the design of the superstructure and substructure and the choice of attachment. Overload by using improper anchorage system not only will cause fracture of the framework or screw but also may cause failure of osseointegration. Choosing anchorage system in making prosthesis, therefore, can be considered to be one of the most important factors that affect long-term success of implant treatment. In this study, in order to determine the effect of anchorage systems on load transfer in mandibular implant overdenture in which 4 implants were placed in the interforaminal region, patterns of stress distribution in implant supporting bone in case of unilateral vertical loading on mandibular left first molar were compared each other according to various types of anchorage system using three-dimensional photoelastic stress analysis. The five photoelastic overdenture models utilizing Hader bar without cantilever using clips(type 1), cantilevered Hader bar using clips(type 2), cantilevered Hader bar with milled surface using clips(type 3), cantilevered milled-bar using swivel-latchs and frictional pins(type 4), and Hader bar using clip and ERA attachments(type 5), and one cantilevered fixed-detachable prosthesis(type 6) model as control were fabricated. The following conclusions were drawn within the limitations of this study, 1. In all experimental models. the highest stress was concentrated on the most distal implant supporting bone on loaded side. 2. Maximum fringe orders on ipsilateral distal implant supporting bone in a ascending order is as follows: type 5, type 1, type 4, type 2 and type 3, and type 6. 3. Regardless of anchorage systems. more or less stresses were generated on the residual ridge under distal extension base of all overdenture models. To summarize the above mentioned results, in case of the patients with unfavorable biomechanical conditions such as not sufficient number of supporting implants, short length of the implant and unfavorable antero-posterior spread. selecting resilient type attachment or minimizing distal cantilever bar is considered to be appropriate methods to prevent overloading on implants by reducing cantilever effect and gaining more support from the distal residual ridge.

• 대한치과의사협회지
• /
• 제56권3호
• /
• pp.142-150
• /
• 2018

In the posterior maxillary area, due to resorption of the ridge after extraction and pneumatization of the maxillary sinus, the height of the alveolar ridge may not be sufficient for placement of implants. To solve this problem, sinus augmentation using both crestal and lateral approaches have been widely used. Jung et al. (2010) introduced the modified lateral approach technique, which is a simplified technique that combines the advantages of crestal and lateral approaches. The purpose of this case report is to report two cases in the posterior maxilla in which simultaneous implant placement with maxillary sinus augmentation has been performed using the modified lateral approach technique. In two female patients, 67 and 74 years old, respectively, simultaneous implant placement was performed using the modified lateral approach technique on the left maxillary second premolar and the first molar. In both patients, the residual bone height on the distal side of the maxillary second premolar was measured to be approximately 5 mm, and the residual bone height of the first molar was measured to be 2-3 mm. After flap elevation, osteotomy of the lateral window was performed in the form of a mesiodistally extended slot above the sinus floor and the Schneiderian membrane was elevated. Sequenced drilling was performed while protecting the membrane with a periosteal elevator. Bone graft and implant placement was performed after preparation of the implant site. Sufficient primary stability was achieved for each implant and sinus membrane was not perforated. After four and five months respectively, implant second surgery was performed. Clinically, the implants were observed to be stable. Implants and surrounding peri-implant mucosa were well maintained after prosthodontic treatment. In conclusion, the modified lateral approach could be a predictable and efficient technique for implant placement in the atrophied posterior maxilla.

• 구강회복응용과학지
• /
• 제28권2호
• /
• pp.179-190
• /
• 2012

후방연장 국소의치에 임플란트를 보조적으로 이용함으로써 부가적으로 유지와 지지를 얻는 임플란트 보조 국소의치(IARPD)에 대한 관심이 증가하고 있다. 하지만 주로 증례발표나 단기적 결과평가에 그치고 있어 철저한 문헌 고찰이 필요하다. PubMed를 이용하여 검색한 IARPD에 대한 문헌은 대부분 실험실 연구이며 낮은 수준의 근거를 가진 임상연구가 대부분이었다. IARPD의 적응증은 아직 완전한 합의에 도달하지는 않았지만 후방연장 부분무치악이 대부분이다. 이 경우 환자들은 연조직의 하방이동이 적어 높은 만족감을 나타내었고 부착장치를 추가 시 만족도가 더욱 증가하였다. 또한 IARPD는 잔존치조제 흡수를 감소시키는 것으로 보인다. IARPD에는 최대한 길이가 길고 직경이 넓은 임플란트가 권장되며, 임플란트 식립위치는 이견이 있으나 제 2소구치 부위나 제2대구치 부위를 선택적으로 결정하는 것이 필요하다. 임플란트는 $15^{\circ}$ 정도의 경사식립도 응력분산에는 무리가 없다고 한다. 임플란트에 치유지대주를 연결하면 풀림이나 파절이 보고되고 있어 개량형 지지-지대주나 탄성 부착장치를 사용하는 것이 좋다. 하지만 자연치 지대치에 사용하는 유지장치와 IARPD를 조화시키는 방법이나 장기적 예후에 대한 추가연구가 필요하다 하겠다.

• Imaging Science in Dentistry
• /
• 제33권2호
• /
• pp.79-83
• /
• 2003

Purpose : To assess the relationship between the direction of the indicating rod of the radiographic stent for ideal prosthetic design and the actual possible path of implant fixture placement when residual ridge resorption is considered. Materials and Methods: The study materials consisted of 326 implant sites (male 214 cases and female 112 cases) from a total of 106 patients (male 65 patients and female 41 patients) who desired implant prostheses. Computed tomography of patients were taken and reformatted using ToothPix/sup (R)/ software. Bony defects, bony sclerosis, the change of the direction of indicating rod, and root proximity of the adjacent teeth were examined on the CT-derived images. Results: The rate of the irregular crestal cortex was relatively high on premolar and molar area of maxilla. Mandibular molar area showed relatively high rate of focal sclerosis on the area of implant fixture insertion. The position of the indicating rods were relatively acceptable on the molar areas of both jaws. However, the position of the indicating rods should be shifted to buccal side with lingual rotation of the apical end on maxillary anterior teeth and premolar area. Conclusion: Clinically determined rod direction and position of the indicating rod for implant placement was not always acceptable for insertion according to the reformatted CT images. The pre-operative treatment plan for implant should be determined carefully, considering the state of the alveolar bone using the reformatted CT images.

• 대한치과보철학회지
• /
• 제32권4호
• /
• pp.526-552
• /
• 1994

The extent and direction of movement of removable partial dentures during function are influenced by the nature of the supporting structures and and the design of the prosthesis. Since forces are transmitted to the abutment teeth through occlusal rests, guide planes and direct retainers during functional movements, proper design based on the avaialble research data will maintain the health of abutment teeth and their supporting structures. The purpose of this in vitro study is evaluating stress distribution clinically around the abutment teeth prepared following 4-type clasping systems for unilateral free-end removable partial dentures. Three-Dimensional Photoelastic Stress Analysis method was used because it shows a visual display of stresses of the simulated abutment teeth and residual ridges and reveals stress concentration that can be read at any given points in terms of direction and magnitude. For this study, the author fabricated 4 mandibular photoelastic epoxy models missing left 1st and End molar. Epoxy models were duplicated and 4 unilateral removable partial dentures were construe- ted in accordance with 4-type direct retainers. Unilateral free-end removable partial dentures were positioned on their own models. 6kg force was loaded on the every removable partial dentures of the epoxy model on the central fossa of mandibular left 1st molar vertically by the loading device. After the stress was frozen in a stress freezing furnace, 6 specimens of 6-mm thickness were made from every epoxy model and examined with the circular polariscope. The results were as follows : 1. Generally I-bar clasp revealed the most favorable stress distribution around the abutment teeth. 2. At the end portion of the free-end ridge, Back action clasp showed the highest stress concentration at the bucco-lingual and top portions of the residual alveolar ridge. 3. At the distal area of the abutment teeth, Akers clasp and Roach clasp showed higher stress concentration bucco-lingually and apically than the others. 4. To the abutment tooth, I-bar clasp showed the least stress distribution bucco-lingually but the others showed irregular stress distribution. 5. At the mesial area of the abutment teeth, the order of effective stress distribution was I-bar clasp, Back-action clasp, Akers clasp and Roach clasp. There was big difference of stress distribution between them. 6. At the right 2nd premolar and 1st molar, the stress concentration of Akers clasp was a little high but that of I-bar clasp was low.

• 한국항해항만학회지
• /
• 제28권6호
• /
• pp.565-572
• /
• 2004

전차륜느 연안역에서 큰 스케일에서의 물질수송에 대한 관점에서 보면 조류보다 더 중요한 역할을 한다. 이러한 잔차류의 주된 성분은 조석 잔차류이며, 취송류, 밀도류 등도 이 흐름을 변동시키는 중요한 인자들이다. 이러한 연안역의 흐름의 특성을 규명하기 위해서는 3차원 유동모델의 적용이 필수적이다. 본 연구는 하천으로부터 담수유입에 의한 연안수역의 성층화 구조를 다루는데 초점을 두었으며, 이를 위해 3차원 밀도류모델을 적용하여 울산만의 유동을 재현하고, 담수유입에 의한 성층화 구조를 규명하였다. 그 결과 울산만과 같이 담수유입이 존재하는 반폐쇄 하구에서는 표층에서는 만외로 유출하고, 저층에서는 만내로 유입하는 흐름이 발생하였다. 또한 만내방향으로의 바람이 존재하는 경우에는 표층에서는 만내로 유입하는 흐름이, 저층에서는 이에 대한 보상류로 만외로 유출하는 흐름이 발생하는 것을 알 수 있었다. 이러한 해수유동결과는 해양목장 조성을 위한 인공어초투하, 연안표사 제어를 위한 잠제건설, 해저산맥 조성 등으로 인한 연직방향으로의 용승현상에 대한 규명이나 심층수 활용을 위한 기초연구에 적용이 가능할 것으로 사료된다.