• Aerospace Engineering and Technology
• /
• v.10 no.1
• /
• pp.1-12
• /
• 2011

The error of onboard propellants mass which is mostly occupied in total mass of launch vehicle and The error of residual affect the performance of launch vehicle seriously. In other words, the errors directly cause the error of total impulse. Therefore, optimization of performance of launch vehicle can be achieved by the minimization of the residual. For minimizing the residuals, the active control for completely depleting the propellants and the calculation method using probability for minimizing the residuals have been researched. In this paper, the added fuel was calculated for minimizing the residual and the minimized residual was predicted by the presented method.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.1
• /
• pp.60-68
• /
• 2001

Thermal Mass Method(TMM) and its accuracy, utilized in the propellant gauging system of KOREA SAT-3, are described in the paper The residual in the fuel tank system of KOREASAT-3 is simulated using TMM based on the KOREASAT-3 data package An accuracy of TMM is calculated using analytical method and compared with the error analysis Monte Carlo methods.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.968-971
• /
• 2017

In this study, manufacturing the Single Base propellant using a Nitroguanidine(NGD A%, NGD-B%, 2A=B). The Factors affecting the combustion rate are Moisture and Volatiles, Residual Solvents, Dimension. These Factors were analyzed and compared. Also, NGD-A% propellants and NGD-B% propellants were compared with firing test Test. As a result, NGD-A% was confirmed to have a higher speed at a similar pressure than NGD-B% propellants.

• Composites Research
• /
• v.19 no.4
• /
• pp.31-38
• /
• 2006

In this study, effects of curing temperature and autofrettage pressure on a Type 3 cryogenic propellant tank, which is composed of composite hoop/helical layers and a metal liner, were investigated by thermo elastic analysis and composite/aluminum ring specimen tests. Temperature field of a Type 3 tank was obtained from solving the heat transfer problem and, in turn, was used as nodal temperature boundary conditions during the elastic analyses for curing temperature and autofrettage pressure effects. As a result, it was shown that the higher curing temperature was, the more residual compressive stress and tensile stress were induced in composites and metal liner, respectively. On the contrary, autofrettage pressure brought the reduction of these residual thermal stresses caused by cryogenic environments to the tank structure. This tradeoff for curing temperature and autofrettage pressure must be considered in the design and manufacturing stages for a Type 3 cryogenic tank.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.1
• /
• pp.8-16
• /
• 2017

Structural integrity of solid rocket depends on the residual reactions between constituents of its composition(post cure, migration etc.), the oxygen(or anti-oxydent) in the free volume and humidity (desiccant) under the perfect sealed condition. Mechanical Properties of composite solid propellant arising from those factors are very complex. Moreover the propulsion are faced with thermal loads from diurnal & seasonal cycle till firing. In this study, the fast evaluation method of long term mechanical properties is suggested based on Thermo-Rheological Simplicity from curing oven to cool-down stage in view point of thermal stabilization. For this subject, endurance tester having temperature control capability are devised. From the results from incremental load and strain, non-linear characteristics are discussed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.218-223
• /
• 2017

This paper deals with a fault diagnosis algorithm using the Kalman filter for a 75-ton Liquid Propellant Rocket Engine (LPRE). To design the Kalman filter, we linearized a non-linear simulation model of a 75-ton LPRE at an operating point, and checked the performance of the Kalman filter by comparing the measured values with estimated values of the states. Then, we artificially injected a fault of the turbopump efficiency into the simulation to confirm the performance of the fault diagnosis algorithm with the developed Kalman filter by comparing the variation of the residuals of the normal state with that of the fault cases.

• Korean Journal of Materials Research
• /
• v.32 no.1
• /
• pp.9-13
• /
• 2022

Bullets flying with a light from the back are called "tracers". Tracers are ignited by the combustion gas of the propellant and emit bright light that allows the shooter to visually trace the flight path. Therefore, tracers mark the firing point for allies to assist shooters to hit target quickly and accurately. Conventional tracers are constructed with a mixture of an oxidizing agent, raw metal, and organic fuel. Upon ignition, the inside of the gun can be easily contaminated by the by-products, which can lead to firearm failure during long-term shooting. Moreover, there is a fire risk such as forest fires due to residual flames at impact site. Therefore, it is necessary to develop non-combustion type luminous material; however, this material must still use the heat generated from the propellant, so-called "thermoluminescence (TL)". This study aims to compare the TL emission of Dy³⁺, La³⁺ and Ho³⁺ doped MgB₄O₇ phosphors prepared by solid state reaction. The crystal structures of samples were determined by X-ray diffraction and matched with the standard pattern of MgB₄O₇. Luminescence of various doses (200 ~ 15,000 Gy) of gamma irradiated Dy³⁺, La³⁺ and Ho³⁺ (at different concentrations of 5, 10, 15 and 20 %) doped MgB₄O₇ were recorded using a luminance/color meter. The intensity of TL yellowish (CIE x = 0.401 ~ 0.486, y = 0.410 ~ 0.488) emission became stronger as the temperature increased and the total gamma-ray dose increased.