• Journal of the Korean Society for Railway
• /
• v.19 no.2
• /
• pp.195-203
• /
• 2016

Concrete slab track was applied to the Gyeoungbu High Speed Railroad step 2 and the Honam High Speed Railroad. Concrete slab track incurs higher construction cost and lower maintenance cost than existing gravel track. For these reasons, the use of concrete slab track has increased in Korea. The biggest problem in the use of concrete slab track is repairing damage from settlement that can occur while trains are in service. High speed railroad design standards require allowable residual settlement of concrete slab track of less than 25mm. In order to satisfy the requirement of long term stability of concrete slab track, it is necessary to manage the secondary compression settlement within the allowable residual settlement. This study is to evaluate the secondary compression settlement with the variation of the secondary compression index, thickness of soft ground, and concrete slab track life. Statistical analysis is performed to determine the probability of distribution of areas where serious problems will be caused after the concrete slab track is constructed.

• Journal of Korean Society of Forest Science
• /
• v.76 no.2
• /
• pp.145-160
• /
• 1987

To evaluate damage status and necessities of repair works on the forest-side erosion control structures constructed from 1966 to 1986 in Korea, developmental procedures of erosion control structures from the standard unit-cost tables established by the Forestry Administration every year, existing counter-measures for disaster erosion control system administrated by the government organization and existing status of each structure at constructed site were investigated and analyzed integrally. About 10-15% of the constructed forest erosion control structures were required to be repaired as a result of the investigation. It is actually incapable of repairing the damaged forest erosion control structures caused by excessive run-off and floodings under the existing forest-side erosion control systems. Therefore, it is necessary to put regularly repair erosion control system that will be secured by national budgetary pre-allocation system. Especially, it is also necessary to frame a new system that repair erosion control works by national budget (central government) should be possible for any scale of damages in case of the erosion control projects for the disaster counter-measures. The results of this research could be adopted as important policy data for erosion control policy-making in forest-side in Korea.

• International Journal of Contents
• /
• v.11 no.1
• /
• pp.41-51
• /
• 2015

Management systems for electronic library have been developed on the basis of Client/Server or ASP framework in domestic market for a long time. Therefore, both service provider and user suffer from their high cost and effort in management, maintenance, and repairing of software as well as hardware. Recently in addition, mobile devices like smartphone and tablet PC are frequently used as terminal devices to access computers through the Internet or other networks, sophisticatedly customized or personalized interface for n-screen service became more important issue these days. In this paper, we propose a new scheme of integrated management system for electronic library based on SaaS and Web Standard. We design and implement the proposed scheme applying Electronic Cabinet Guidelines for Web Standard and Universal Code System. Hosted application management style and software on demand style service models based on SaaS are basically applied to develop the management system. Moreover, a newly improved concept of duplication check algorithm in a hierarchical evaluation process is presented and a personalized interface based on web standard is applied to implement the system. Algorithms of duplication check for journal, volume/number, and paper are hierarchically presented with their logic flows. Total framework of our development obeys the standard feature of Electronic Cabinet Guidelines offered by Korea government so that we can accomplish standard of application software, quality improvement of total software, and reusability extension. Scope of our development includes core services of library automation system such as acquisition, list-up, loan-and-return, and their related services. We focus on interoperation compatibility between elementary sub-systems throughout complex network and structural features. Reanalyzing and standardizing each part of the system under the concept on the cloud of service, we construct an integrated development environment for generating, test, operation, and maintenance. Finally, performance analyses are performed about resource usability of server, memory amount used, and response time of server etc. As a result of measurements fulfilled over 5 times at different test points and using different data, the average response time is about 62.9 seconds for 100 clients, which takes about 0.629 seconds per client on the average. We can expect this result makes it possible to operate the system in real-time level proof. Resource usability and memory occupation are also good and moderate comparing to the conventional systems. As total verification tests, we present a simple proof to obey Electronic Cabinet Guidelines and a record of TTA authentication test for topics about SaaS maturity, performance, and application program features.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.26 no.2
• /
• pp.73-90
• /
• 1998

The construction and management of the royal garden and landscape were the most significant project in Choson Dynasty. The kind of the royal garden and landscape were the rear garden of the palace, the groves of the royal shrine and orchard, etc. As the important project of the country, these constructions were controlled by the administrative system without division into the fields of engineering, building and landscaping. The purpose of this study is to investigate the administrative system. In particular, this study is focused on the construction and management of the royal garden and landscape in Hanyang from the 18th century to the late 19th century. This study is based on the analysis of historic documents and a survey of the relics. The results were summarized as follows : 1) The administrative system of the construction and management of the royal garden and landscape was composed of the government offices under Industry Board as a permanent organization - Yongjosa, Santaeksa, Chunchonsa, Songonggam, Changwonso - and Togam as a temporary organization. In addition to these organizations, there were Revenue Board, Ceremony Board, Military Board, which served as supporting organizations. The control of the construction and management of the royal garden and landscape was held by decision makers, executors of works and management. 2) The general process of the construction and management of the royal garden and landscape included Sangji and Kyuho다 as the first step; In case of buildings and facilities, according to former examples and drawings, the most of the planning and design was already fixed. In the case of landscape, those things aimed at construction according to the existing lie of the land. The works in the 2nd step; This process was divided into the construction of facilities and planting. In case of construction of facilities, those works were done by Togam and Songonggam. The high cost works were carried out through Togam and normal repairing works were completed by Songonggam. In case of planting, those works were carried out through Chunchonsa and the military. The management in the 3rd step; This process was done by two parts like the process of works. In case of facilities, management was done 효 the officers of Pongshim. In case of groves of newly - planted trees, this management was done by Tongsanbyonlgam and Tongsanjik who served cultivation and harvest of fruit trees as an expert.

• KIPS Transactions on Computer and Communication Systems
• /
• v.5 no.4
• /
• pp.79-86
• /
• 2016

About 75% of software security incidents are caused by software vulnerability. In addition, the after-market repairing cost of the software is higher by more than 30 times than that in the design stage. In this background, the secure coding has been proposed as one of the ways to solve this kind of maintenance problems. Various institutions have addressed the weakness patterns of the standard software. A new Korean programming language Saesark has been proposed to resolve the security weakness on the language level. However, the previous study on Saesark can not resolve the security weakness caused by the API. This paper proposes a way to resolve the security weakness due to the API. It adopts a static analyzer inspecting dangerous methods. It classifies the dangerous methods of the API into two groups: the methods of using tainted data and those accepting in-flowing tainted data. It analyses the security weakness in four steps: searching for the dangerous methods, configuring a call graph, navigating a path between the method for in-flowing tainted data and that uses tainted data on the call graph, and reporting the security weakness detected. To measure the effectiveness of this method, two experiments have been performed on the new version of Saesark adopting the static analysis. The first experiment is the comparison of it with the previous version of Saesark according to the Java Secure Coding Guide. The second experiment is the comparison of the improved Saesark with FindBugs, a Java program vulnerability analysis tool. According to the result, the improved Saesark is 15% more safe than the previous version of Saesark and the F-measure of it 68%, which shows the improvement of 9% point compared to 59%, that of FindBugs.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.4
• /
• pp.221-232
• /
• 2021

Most of measurement sensors used for maintenance are continuously exposed to various environmental factors such as transportation and rainfall, so the possibility of breakage increases gradually. The maintenance measurement sensor of domestic subway tunnel shows an average of 14.2% to 14.8% of loss rate after about 5 to 6 years from installation, and it shows a sensor loss rate of about 13.9% in case of foreign countries. As a result, it can be seen that an average of 15% of maintenance measurement sensors at home and abroad cannot send measuring values after 5~6 years. In order to continuously collect accurate data, measurement data must be recovered by performing repair or replacement of the sensor, but some lost measurement sensors are buried after installation. So, there are many difficulties in repairing sensors, including cost and time. Therefore, in this paper, we propose lost measurement sensor data estimation technology based on data trend analysis using adjacent sensors.

• Journal of the Korea Institute of Building Construction
• /
• v.21 no.6
• /
• pp.653-664
• /
• 2021

As the construction standards for energy-saving eco-friendly housing have recently been strengthened, the proportion of window work has increased with the demand for high-efficiency housing. Windows have high frequency of use, and there is the potential for many defects to occur depending on the characteristics of construction. According to a government agency's survey of defects in public rental apartment housing, defects in the windows work accounted for the highest portion of complaints received. Accordingly, related previous studies were considered, and it was found that the existing studies in Korea lacked research that reflected the construction characteristics of window work and the importance of maintenance. In addition, existing overseas studies considered both the constructor and the resident's position, considering the cost aspect together, and showed a trend of structuring the relationship between defects and causes. Therefore, this study will analyze the causes of defects that can occur in the construction phase of the windows work, reflect the construction characteristics, and derive major factors that consider the importance of maintenance based on the possibility of recurrence after repairing defects. Ultimately, this research will contribute to preventing defects in the construction phase and reducing maintenance costs by presenting a highly effective defect management plan through selecting the major factors for each defect type that can be intuitively judged by analyzing the causal relationship between defect types and causes.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.40 no.2
• /
• pp.82-90
• /
• 2024

It often happens that a removable partial denture needs to be repaired due to tissue changes in the remaining alveolar ridge, fracture of the denture, or fracture of the abutment tooth. There are several advantages to retrofitting a customized surveyed crown under the existing RPD. Retrofitting a crown to the RPD decreases the economic burden to the patient and avoids the need for several appointments to fabricate a new RPD. It is difficult for artificial teeth used to repair dentures due to fractured natural teeth to have a shape similar to that of natural teeth, and to repair aesthetic artificial teeth, it is necessary to manufacture customized artificial teeth similar to the shape of each patient's teeth. Recently, CAD/CAM technology has been used to fabricate customized prosthetics on existing RPD to achieve high retention and fitness accuracy, and by manufacturing customized artificial teeth, more aesthetic and harmonious artificial tooth repair is possible. This is a case in which a denture was repaired using a digital method to fabricate a customized prosthesis on an existing partial denture and customized artificial teeth that mirrored the adjacent dentition, saving time and cost, simplifying the process, and achieving aesthetically and functionally satisfactory results.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.40 no.3
• /
• pp.81-90
• /
• 2012

Improvements in the quality of life have resulted in a heightened awareness of safety and the environment. As a result, timber as an environmentally friendly material, is used for landscape facilities and a wide range of purposes. But there are a large number of defects since there are twists and cracks that can be found in wooden landscape facilities. This has led to the use of imported hardwood instead of the Western Hemlock which has been in widespread use. Hardwood is expensive. However, it is being used without any information or research on how much it reduces the actual defects. Construction contractors are in great need of information on the characteristics and defect rates of different types of timber. This study investigated and analyzed the cracks in four types of timber - namely the Western Hemlock, Burckella, Nyatoh and Malas - in order to provide basic information to construction contractor for them to be able to select and use the appropriate type of timber. The main results of this study are as follows. First, the Western Hemlock had 1.90 $cracks/m^2$, Malas had 0.83 $cracks/m^2$, Burckella had 0.14 $cracks/m^2$, and the Nyatoh had the least number of surface defects at 0.04 $cracks/m^2$. Second, while Malas has the highest degree of strength timber, Nyatoh had the smallest defect rate. This showed that having high timber strength does not necessarily mean it has less defects. Third, the Western Hemlock was the least expensive and Burckella was the most expensive. However, considering the cost of repairing defects, it would be economically advantageous to use Burckella and Nyatoh which have low defect rates. This study aimed to provide basic information to landscape construction contractors for them to be able to select and use the appropriate type of timber when constructing wooden outdoor rest furniture. The results are expected to contribute to quality enhancements and defect reduction in landscape facilities.

• Journal of the Korean association of regional geographers
• /
• v.3 no.1
• /
• pp.183-198
• /
• 1997

This case study was conducted by verification the site characteristics based on the questionnaire and interview obtained from the all factories located at No. 1 developing area in Kumi industrial complex. The site characteristics were presumed from the process of location behavior and spatial linkage. Kumi industrial complex was developed to improve export industry at national levels by providing chief land price and benefiting various tax. Kumi industrial complex which enticed many factories is playing an important role in export industry in Korea. At beginning, the detention of large enterprises promoted the establishment of related small to medium sized factories into the complex. Two distinctive industries. textile and electronic, were reflected by the purpose to establish the complex and industrial characteristics of Taegu city. respectively. In Kumi industrial complex, positive responses on traffic and raw material supply and negative reactions on the environmental impact on social community as well as high labor charge were investigated. Especially the higher labor cost prevented to hire laborers effectively. In the linkages of spatial and raw material, most factories in the complex depended on the availability of out side the Kumi city. For the textile factories, the supply of raw material and parts were relied on Taegu and/or other cities, whereas in electronic factories purchased them mainly from other cities and partly from abroad. Although questionnaire and interview suggested it, most of the parts were supplied by a parts maturing companies on the complex to a few large enterprises. In the marketing linkage, textile factories revealed higher relation-ship with the foreign countries and sewing factories in Korea. On the other hand, electronic factories have strong relation-ships in the marketing linkage to the parts supplying companies in the complex or large-scale resembling companies in other cities. In the textile companies, the right for decision on purchasing raw materials and parts is belonging to the owner whereas mother enterprise usually have the right for the marketing. In the case of the electronic factories, all the purchasing activities are related to the sub-contracting companies. In the service linkage, the Quality of the service created spatial distinction. There was high linkages on inside of Kumi complex for the low grade services such as repairing and installing machines, whereas strong linkages on outside of the complex for the high grade services such as management, law, taxation, new product development. and manufacturing technology. In the linkages of activity on the R&D (research and development), electronic factories do not have sufficiently qualified institutes in the complex. Strong regional linkages in the field of textile and electronic industries revealed limitations of the local industrial complex. In the sub-contracting linkage, high linkage ship within Kumi boundary reflected the characteristics of industrial site in the complex. There, most decisions by the companies centered by the mother enterprise.