• IEMEK Journal of Embedded Systems and Applications
• /
• v.15 no.4
• /
• pp.159-166
• /
• 2020

The IBC (Intra-Body Communication) benefits from a wireless communication system for exchanging various kinds of digital information through wearable electronic devices and sensors. The IBC using the human body as the transmission channel allows wireless communication without the transmitting radio frequency waves to the air. This paper discusses the results of experiments on electrostatic coupling IBC based on FSK (Frequency Shift Keying) and 1 bit error correction. We implemented FSK communication and 1 bit error correction algorithm using the MCU boards and aluminum tape electrodes. The transmitter modulates digital data using 50% duty square wave as carrier signal and transmits data through human body. The receiver performs ADC (Analog to Digital Conversion) on carrier signal from human body. In order to figure out the frequency of carrier signal from ADC results, we applied zero-crossing algorithm which is used to detect the edge characteristic in computer vision. Experiment results shows that digital data modulated as square wave can be successfully transmitted through human body by applying the proposed architecture of a 1ch GPIO as a transmitter and 1ch ADC for as a receiver. Also, this paper proposes 1 bit error correction technique for reliable IBC. This technique performs error correction by utilizing the feature that carrier signal has 50% duty ratio. When 1 bit error correction technique is applied, the byte error rate at receiver side is improved around 3.5% compared to that not applied.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.7
• /
• pp.9-19
• /
• 2004

WLAN (Wireless Local Area Networks) needs error recovery and flow control schemes to support reliable multicast protocol. Limited wireless bandwidth, as well as queuing losses caused by the asymmetric wired/wireless interactions, demands more effective approaches for reducing packet losses. Moreover, since the wireless channel is a shared broadcast medium, if sender receives feedback information simultaneously from several receivers, the feedback delays data frame transmission of forward direction by introducing channel congestion and burden at the sender. Therefore, it is important to minimize the amount of feedback information from receivers. In this paper, we propose an ARS(Adaptive Redundancy Scheme) that combines FEC(Forward Error Correction) using channel state estimation and ARQ(Automatic Repeat Request) both to reduce the amount of feedback information and the number of retransmissions and to guarantee high data reliability in a WLAN multicast environment. Performance of the proposed scheme is evaluated by means of analysis and simulations in AWGN and Rayleigh fading channels. The results show that the proposed scheme reduces the amount of feedback information and the number of retransmissions and guarantees high data reliability, while keeping throughput efficiency similarly with the conventional FEC and ARQ scheme.

• Journal of the Korea Society of Computer and Information
• /
• v.17 no.12
• /
• pp.137-148
• /
• 2012

In this paper, we proposed the location-aware coordinate routing algorithm for improving the performance of routing algorithm by using ZigBee in Smart Grid environment. A distributed address allocation scheme used an existing algorithm that has wasted in address space. The x, y and z coordinate axes from divided address space of 16 bit to solve this problems. However, coordinate routing does not take account of wireless link condition. If wiress link condition is not considered, when the routing table is updated, the nodes with bad link conditions are updated in the routing table and can be chosen as the next hop. This brings out the retransmissions because of received packet's errors. Also, because of these retransmissions, additional power is consumed. In this paper, we propose the location-aware coordinate routing algorithm considering wiress link condition, where reliable data transmission is made and the consumed enegy is minimize. and we compared and connected region and transition region of ZigBee location based routing in the aspect of average number of multi hops, subordinate packet delivery ratio, delay time, and energy consumption of proposed algorithm. It turned out that there were improvements in performances of each items.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.11A
• /
• pp.1059-1067
• /
• 2006

AODV(Ad-hoc On-demand Distance Vector) routing protocol was devised for use of mobile nodes in Ad-hoc network. When we use the AODV routing protocol in Ad-hoc networks with high mobility, disturbance of optimized route path and link break occur. In order to solve the shortcomings, this paper proposes a new routing protocol in which new routing control messages are added to the existing AODV. The proposed protocol minimizes link break and transmission delay while is able to secure the optimized route path constantly in changes of network topology The performance of the proposed routing protocol was evaluated by using us2 network simulator. The actual Ad-hoc network test bed provides us the most reliable experimental data for Ad-hoc networks. In order to support this experimental environment, the dissertation also developed an efficient embedded system on which AODV routing protocol, NAT, Netfilter can run and other event message can be verified without declining efficiency. The correct operation of AODV routing protocol has been verified in both the Ad-hoc network test bed in which the embedded system was used, and Ad-hoc networks linked with Ethernet backbone network.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.11A
• /
• pp.1085-1091
• /
• 2006

For an experiment in this paper, designed test bed to secure confidentiality of data and safe transmission that Mobile node exchanges in Mobile network. And, For IPsec use that support basically in MIPv6, modeling and experimented IKEv2 protocol that is used for reliable authentication key management and distribution between End Point. When Mobile node handoff in Mobile network, analyzed effect that authentication key re-exchange and limited bandwidth that happen often get in key exchange. And studied about Performance and latency about authentication setting and exchange process that use multi interface. To conclusion, when Mobile node transmits using IPSec, re-authentication of key confirmed that re-setting by limit of bandwidth that existent Mobile network has can be impossible. According to other result, proposed MN's multi interface is expected to minimise key exchange latency by hand-off when transmit IPSec.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.1
• /
• pp.193-197
• /
• 2015

Recently, the new issues for the safety and the information delivery system in the ship are raised. The deployment and the efficient algorithms of deploying the wireless sensor networks instead of using the built-in wired networks or the setup of the new wired networks is more desirable than the deployment of the wired networks in a ship after its final production since it can reduce the cost and the time of the brand new wired networks by reshaping some of the internal structure of the ship. In this paper, the shipboard signal propagation measurement system based on the signature sequence-three way slave mode are designed and its measureed data are analysed after measuring the signal propagation characteristics. Consequently, it is expected that the reliable and cost-effective signal measurement system with the three way algorithm for the deployment of the shipboard wireless networks can be achieved.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.1
• /
• pp.183-186
• /
• 2015

Recently, the demand for the safety and the information delivery system in the ship increases. The deployment of the wireless sensor networks instead of using the built-in wired networks or the setup of the new wired networks is more desirable than the deployment of the wired networks in a ship after its final production since it can reduce the cost and the time of the brand new wired networks by deforming some of the internal structure of the ship. In this paper, the shipboard signal propagation measurement system based on the signature sequence-two way slave mode are designed and its measurement data are analysed after measuring the signal propagation characteristics. Consequently, it is expected that the reliable and cost-effective signal measurement system for the deployment of the shipboard wireless networks can be built.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.8B
• /
• pp.954-961
• /
• 2011

To apply Wi-Fi technique to the Broadcast field, we have to study features of IEEE 802.11 Broadcast packet. IEEE 802.11 Broadcast technique cannot guarantee successful packet delivery than IEEE 802.11 Unicast. A promising solution to this problem is the use of FEC(Forward Error Correction) mechanisms. However, the adjustment of the FEC redundancy rate is not a trivial issue due to the dynamic wireless environment. In order to explore the above issues we conducted an experimental study of the packet loss behavior of the IEEE 802.11g protocol. In order to study, we implemented a broadcast test bed. Based on the experimental results, we provide guidelines on wireless lan parameters(packet size, transmission rate(11g), background traffic). From this experimental study, we provide FEC redundancy rate.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39B no.3
• /
• pp.169-179
• /
• 2014

For vehicle safety-related services using wireless communications, reliable collection of various driving informations transmitted periodically by neighbor vehicles is the most important. Every host vehicle analyses them to estimate a potential dangerous situation in a very short time and warns drivers to prevent an accident. However tremendous amount of periodic messages can cause the wireless communication in chaos and the services not in safe. In this paper, we propose a time-division broadcasting protocol to mitigate the communication congestion. It utilizes the received information of vehicle velocity and location, i.e. vehicle traffic density on a road to adjust the number of time slots in a given broadcasting period, and transmission power. The simulation results show that message reception ratio is changed to approximately 40% and channel access time also decreased from 10ms to 0.23ms.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.1
• /
• pp.109-119
• /
• 2013

This paper presents the design of the Safety Programmable Logic Controller (SPLC) used in the Nuclear Power Plants, an analysis of a reliability for the SPLC using a markov model. The architecture of the SPLC is designed to have the multiple modular redundancy composed of the Dual Modular Redundancy(DMR) and the Triple Modular Redundancy(TMR). The operating system of the SPLC is designed to have the non-preemptive state based scheduler and the supervisory task managing the sequential scheduling, timing of tasks, diagnostic and security. The data communication of the SPLC is designed to have the deterministic state based protocol, and is designed to satisfy the effective transmission capacity of 20Mbps. Using Markov model, the reliability of SPLC is analyzed, and assessed. To have the reasonable reliability such as the mean time to failure (MTTF) more than 10,000 hours, the failure rate of each SPLC module should be less than $2{\times}10^{-5}$/hour. When the fault coverage factor (FCF) is increased by 0.1, the MTTF is improved by about 4 months, thus to enhance the MTTF effectively, it is needed that the diagnostic ability of each SPLC module should be strengthened. Also as the result of comparison the SPLC and the existing safety grade PLCs, the reliability and MTTF of SPLC is up to 1.6-times and up to 22,000 hours better than the existing PLCs.