• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.9
• /
• pp.712-719
• /
• 2008

Light Oil Flow Standard System(LOFSS), as a national oil flow standard system, in Korea Research Institute of Standards and Science(KRISS) was developed for oil flowmeter calibration, and the expanded uncertainty of flow quantity determination was estimated within 0.04 %. In order to improve the reliability of the LOFSS measurement, a proficiency test was carried out in the flow range of 20 and $240\;m^3/h$ (Reynolds number $20,000{\sim}900,000$). A turbine flowmeter was used as a transfer package in round robin test. The water flow standard system of KRISS, the pipe prover of the national calibration and test organization and the master meter calibrator of the turbine flowmeter supplier, which used the different working fluid respectively, were compared with the turbine flowmeter measurement. The maximum difference of measurement was 0.15 % between the LOFSS and the pipe prover. The En numbers of the each system measurement were evaluated at the same Reynolds number. It was found that the En numbers were less than 1 in the comparison, which means the procedures of the uncertainty estimation of the each calibrators were reasonable and reliable.

• Journal of Environmental Science International
• /
• v.19 no.10
• /
• pp.1229-1235
• /
• 2010

Three meteor-statistical forecasting models - the transfer function model, the time-series autoregressive model and the neural networks model - were tested to develop a daily forecasting model for Jejudo, where the need and demand for wind power forecasting has increased. All the meteorological observation sites in Jejudo have been classified into 6 groups using a cluster analysis. Four pairs of observation sites among them, all having strong wind speed correlation within the same meteorological group, were chosen for a model test. In the development of the wind speed forecasting model for Jejudo, it was confirmed that not only the use a wind dataset at the objective site itself, but the introduction of another wind dataset at the nearest site having a strong wind speed correlation within the same group, would enhance the goodness to fit of the forecasting. A transfer function model and a neural network model were also confirmed to offer reliable predictions, with the similar goodness to fit level.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.3B
• /
• pp.487-492
• /
• 2000

The ABR(available bit rate) service has been developed to support data application over ATM(asynchronous Transfer mode) networks, and TCP is the most widely used transport layer protocol in existing data networks. Thus, the performance improvement of TCP over ABR is an issue of cardinal importance. In this paper, we propose algorithm of the adjustment of congestion window size utilizing RM(resource Management) cell information. The motivation is to use more reliable information in ER(explicit rate) field within RM cell to determine TCP window size. Simulations are performance using the suggested algorithm is improved, as compared to TCP-reno.

• Journal of Embryo Transfer
• /
• v.32 no.3
• /
• pp.105-109
• /
• 2017

Autophagy is an intracellular degradation and recycling system. Oocyte maturation is dynamic process, in which various proteins should be synthesized and degraded. In our previous study, we reported the loci of autophagosome and dynamics of autophagic activity in porcine oocytes during in vitro maturation. In this study, we verified loci of autophagosome in porcine follicular cumulus-oocyte complex by detection of microtubule-associated protein 1A/1B-light chain 3 (LC3) which is the reliable marker of autophagosome. Porcine ovary including various sizes of follicles was fixed within 1 hour after collection from slaughterhouse. After fixation, immunohistochemistry was conducted on sliced ovary tissue containing various sizes of follicles by using LC3 antibody. As a result, LC3 signal was clearly detected in both cumulus and oocytes of various sizes of follicles. We also found ring shaped signal which represent autophagosome near oocyte membrane. Most of the signals in oocytes were localized nearby cellular membrane while evenly dispersed in cumulus cells. Therefore, this result suggests that autophagy occurs in porcine COCs (cumulus-oocyte complexes) at follicular stage.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.2
• /
• pp.141-150
• /
• 2012

The present study examines an efficient congestion management system compatible with the evolving environment. The key is to build an information model shared and exchanged for marketbased solutions to alleviate congestion. Traditional methods for congestion management can be classified into two categories, i.e., the centralized scheme and the decentralized scheme, depending on the extent to which the independent system operator (ISO) is involved in market participants' (MPs) activities. Although the centralized scheme is more appropriate for providing reliable system operation and relieving congestion in near real-time, the decentralized scheme is preferred for supporting efficient market operation. The minimum set of information between the ISO and MPs for decentralized scheme is identified: i) congestion-based zone, ii) Power Transfer Distribution Factors, and iii) transmission congestion cost. The mathematical modeling of the proposed information is expressed, considering its process of making effective use of information. Numerical analysis is conducted to demonstrate both cost minimization from the MP perspective and the reliability enhancement from the ISO perspective based on the proposed information exchange scheme.

• Journal of Welding and Joining
• /
• v.16 no.3
• /
• pp.95-101
• /
• 1998

Waveforms of $CO_2$ gas shielded arc welding in short circuit transfer mode was studied with the waveform analysis program, which can calculate various waveform factors such as number of short circuit event, mean and standard deviation of short circuit time and arc time. The calculated values of these factors were correlated independently or in combination with the spatter generation rate to figure out the most reliable index for evaluating spatter generation and further for arc stability. As a result this study, it was confirmed that the spatter generation tends to decrease with the increase of short circuit frequency. Further to this, it was also found that as the short circuit frequency increases the short circuit event becomes more uniform resulting in the decrease of standard deviations ($\sigma$values) of short circuit time and arc time. This result demonstrated that these factors are strongly correlated with each other and thus any one of these factors can be used for the evaluation index. In the discussion, however, short circuit frequency was proposed for the most practical index in evaluating the arc stability of short circuit transfer mode since it is the one which could be monitored in-process condition without any complex caculation process.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.287-292
• /
• 2005

This paper presents a rational polynomial approximation method to estimate modal parameters of wind excited structures using incomplete noisy measurements of structural responses and partial measurements of wind velocities only. A stochastic model of the excitation wind force acting on the structure is estimated from partial measurements of wind velocities. Then the transfer functions of the structure are approximated as rational polynomial functions. From the poles and zeros of the estimated rational polynomial functions, the modal parameters, such as natural frequencies, damping ratios, and mode shapes are extracted. Since the frequency characteristics of wind forces acting on structures can be assumed as a smooth Gaussian process especially around the natural frequencies of the structures according to the central limit theorem (Brillinger, 1969; Yaglom, 1987), the estimated modal parameters are robust and reliable with respect to the assumed stochastic input models. To verify the proposed method, the modal parameters of a TV transmission tower excited by gust wind are estimated. Comparison study with the results of other researchers shows the efficacy of the suggested method.

• Bulletin of the Korean Chemical Society
• /
• v.20 no.10
• /
• pp.1177-1180
• /
• 1999

The ab initio SCF MO and density functional theory (DFT) studies are carried out on the electrophilic (1a) and electron transfer (1b) addition reactions to the vinyl double bond of aryl vinyl sulfides and ethers. In the electrophilic addition processes, a double bond shift from C3 = C4 to X = C3 occurs with occupation number (1.97) close to the normal two. Due to this shift direct conjugation between the cationic center, X = S or O, and the para electron-donor substituent becomes impossible so that the reaction energies (or log K) are correlated with σ rather than σ+. By contrast, radical cation formation leads to delocalization of the SOMO, a lone-pair πorbital on X, with four major resonance structures in which cationic charge as well as spin density is delocalized over C4 , X and C7 atoms. As a result, partial πbonds are formed over C1 -X and C3 - C4 with occupation numbers (0.82) lower than one. In two of the cannonical structures, III(Ⅹ) and III(X+), direct conjugation between the cationic center, X, and the para substituent is achieved so that a better correlation with σ+ rather than σis obtained. The SCF MO energies at the HF/3-21G* and HF/6-31G* levels lead to very much inferior Hammett correlations in the σ/ σ+ diagnostic criterion. In contrast, the ρvalues evaluated with the DFT energies can give reliable diagnostic distinction between the two addition mechanisms.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.42
• /
• pp.2.1-2.6
• /
• 2020

Background: Facial palsy treatment comprises static and dynamic techniques. Among dynamic techniques, local temporalis transposition represents a reliable solution to achieve facial reanimation. The present study describes a modification of the temporalis tendon transfer using a cryopreserved fascia allograft. Case presentation: Between March 2015 and September 2018, seven patients with facial palsy underwent facial reanimation with temporalis tendon transfer and fascia lata allograft. Patients with long-term palsy were considered, and both physical and social functions were evaluated. The mean follow-up time was 21.5 months. No immediate complications were observed. Patients reported improvement in facial symmetry both in static and dynamic. Improvement was noticed also in articulation, eating, drinking, and saliva control. The Facial Disability Index revealed an improvement both in physical function subscale and in the social/well-being function subscale. Conclusions: This modified orthodromic technique allows to reduce the operative time and the risk of complications connected to the use of autologous tissues. The use of the cryopreserved fascia allografts from cadaveric donors seems to provide promising and long-standing results in the treatment of facial palsy.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.4
• /
• pp.262-268
• /
• 2021

For the past several decades, various next-generation patterning methods have been developed to obtain well-designed nano-to-micro structures, such as imprint lithography, nanotransfer printing (nTP), directed self-assembly (DSA), E-beam lithography, and so on. Especially, nTP process has much attention due to its low processing cost, short processing time, and good compatibility with other patterning techniques in achieving the formation of high-resolution functional patterns. To transfer functional patterns onto desirable substrates, the use of soft materials is required for precise replication of master mold. Here, we introduce a simple and practical nTP method to create highly ordered structures using various polymeric replica materials. We found that polymethyl methacrylate (PMMA), polystyrene (PS), and polyvinylpyridine (PVP) are possible candidates for replica materials for reliable duplication of Si master mold based on systematic analysis of pattern visualization. Furthermore, we successfully obtained well-defined metal and oxide nanostructures with functionality on target substrates by using replica patterns, through deposition and transfer process. We expect that the several candidates of replica materials can be exploited for effective nanofabrication of complex electronic devices.