• International Journal of Reliability and Applications
• /
• v.2 no.1
• /
• pp.37-48
• /
• 2001

This paper presents a new dynamic human reliability analysis method and its application for quantifying the human error probabilities in implementing management action. For comparisons of current HRA methods with the new method, the characteristics of THERP, HCR, and SLIM-MAUD, which are most frequency used method in PSAs, are discussed. The action associated with implementation of the cavity flooding during a station blackout sequence is considered for its application. This method is based on the concepts of the quantified correlation between the performance requirement and performance achievement. The MAAP 3.0B code and Latin Hypercube sampling technique are used to determine the uncertainty of the performance achievement parameter. Meanwhile, the value of the performance requirement parameter is obtained from interviews. Based on these stochastic obtained, human error probabilities are calculated with respect to the various means and variances of the things. It is shown that this method is very flexible in that it can be applied to any kind of the operator actions, including the actions associated with the implementation of accident management strategies.

• Applied Microscopy
• /
• v.47 no.3
• /
• pp.126-130
• /
• 2017

The dielectric relaxation characteristics of composites with different concentrations of carbon nanotubes loaded in an epoxy polymer matrix has been studied as a function of frequency over a wide range (1 Hz~10 MHz) at room temperature. Two characterization techniques were used in this work to measure and calculate the dimensionality parameters: small angle neutron scattering and impedance spectroscopy. The results obtained from both methods are in good agreement, indicating the reliability of the estimated fractal dimension, despite of the difference in the length scales accessed by the two techniques.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.207-207
• /
• 2010

Both ZnO and GaN have excellent physical properties in optoelectronic devices such as blue light emitting diode (LED), blue laser diode (LD), and ultra-violet (UV) detector. The ZnO/GaN heterostructure, which has a potential to achieve the cost efficient LED technology, has been fabricated by using radio frequency (RF) sputtering, pyrolysis, metal organic chemical vapor deposition (MOCVD), direct current (DC) arc plasmatron, and pulsed laser deposition (PLD) methods. Among them, the PLD system has a benefit to control the composition ratio of the grown film from the mixture target. A 500-nm-thick ZnO film was grown by PLD technique on c-plane GaN/sapphire substrates. The post annealing process was executed at some varied temperature between from $300^{\circ}C$ to $900^{\circ}C$. The morphology and crystal structural properties obtained by using atomic force microscope (AFM) and x-ray diffraction (XRD) showed that the crystal quality of ZnO thin films can be improved as increasing the annealing temperature. We will discuss the post-treatment effect on film quality (uniformity and reliability) of ZnO/GaN heterostructures.

• Nuclear Engineering and Technology
• /
• v.54 no.5
• /
• pp.1804-1812
• /
• 2022

The aim of this paper is to assess the reliability and accuracy of the PSI standard method, used in many previous works, for the quantification of ND uncertainties in the SPERT-III RIA transient, by quantifying the discrepancy between the actual inserted reactivity and the original static reactivity worth and their associated uncertainties. The assessment has shown that the inherent S3K neutron source renormalization scheme, introduced before starting the transient, alters the original static reactivity worth of the transient CR and reduces the associated uncertainty due to the ND perturbation. In order to overcome these limitations, two additional methods have been developed based on CR adjustment. The comparative study performed between the three methods has showed clearly the high sensitivity of the obtained results to the selected approach and pointed out the importance of using the right procedure in order to simulate correctly the effect of ND uncertainties on the overall parameters in a RIA transient. This study has proven that the approach that allows matching the original static reactivity worth and starting the transient from criticality is the most reliable method since it conservatively preserves the effect of the ND uncertainties on the inserted reactivity during a RIA transient.

• Korean Journal of Metals and Materials
• /
• v.47 no.12
• /
• pp.842-851
• /
• 2009

The long-term reliability of Sn-0.3wt%Ag-0.7wt%Cu solder joints was evaluated and compared with Sn-3.0wt%Ag-0.5wt%Cu under thermal shock conditions. Test vehicles were prepared to use Sn-0.3Ag-0.7Cu and Sn-3.0Ag-0.5Cu solder alloys. To compare the shear strength of the solder joints, 0603, 1005, 1608, 2012, 3216 and 4232 multi-layer ceramic chip capacitors were used. A reflow soldering process was utilized in the preparation of the test vehicles involving a FR-4 material-based printed circuit board (PCB). To compare the shear strength degradation following the thermal shock cycles, a thermal shock test was conducted up to 2,000 cycles at temperatures ranging from $-40^{\circ}C$ to $85^{\circ}C$, with a dwell time of 30 min at each temperature. The shear strength of the solder joints of the chip capacitors was measured at every 500 cycles in each case. The intermetallic compounds (IMCs) of the solder joint interfaces werealso analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). The results showed that the reliability of Sn-0.3Ag-0.7Cu solder joints was very close to that of Sn-3.0Ag-0.5Cu. Consequently, it was confirmed that Sn-0.3Ag-0.7Cu solder alloy with a low silver content can be replaced with Sn-3.0Ag-0.5Cu.

• Nuclear Engineering and Technology
• /
• v.52 no.6
• /
• pp.1208-1212
• /
• 2020

Knowledge on fuel enthalpy and its temperature derivative, the heat capacity, are important quantities in determination of fuel behavior in normal reactor operation and reactor transients. The aim of this study is to compare the heat capacity of oxide and nitrite fuels by using Einstein-Debye approximation. A simple analytical expression was performed to calculate the heat capacity of fuels. To test the validity and reliability, the calculated formulas were compared to published results for various nuclear fuels including UO₂, ThO₂, PuO₂ and UN. Calculated formulas yielded results in consistent with literature.

• Progress in Superconductivity and Cryogenics
• /
• v.11 no.2
• /
• pp.11-14
• /
• 2009

We estimated the critical current distribution of the long length CCs using hall probe method, and checked the reliability by comparing with the four-probe dc transport method. The deviation ratio of $I_{c-T}$ (a measured critical current by four probe dc transport method) and $I_{c-H}$ (calculated critical current by formula (3).) was nearly smaller than 12%. The Hall probe method appeared powerful to evaluate the critical current of CCs in a reel to reel system.

• Current Optics and Photonics
• /
• v.7 no.1
• /
• pp.90-96
• /
• 2023

We numerically solve the nonlinear Schrödinger equation for pulse propagation in a passively mode-locked Yb:KGW laser. The soliton-like pulse formation as a result of balanced negative group-delay dispersion (GDD) and nonlinear self-phase modulation is analyzed. The cavity design and optical parameters of a previously reported high-power Yb:KGW laser were adopted to compare the simulation results with experimental results. The pulse duration and energy obtained by varying the small-signal gain or GDD reproduce the overall tendency observed in the experiments, demonstrating the reliability and accuracy of the model simulation and the optical parameters.

• Journal of The Korean Association For Science Education
• /
• v.34 no.7
• /
• pp.693-701
• /
• 2014

Based on social cognitive theory, self-efficacy in the context of learning has been steadily emphasized as an indicator of students' motivation and performance. The premise for developing such an instrument was that a specific measure of Physics self-efficacy was deemed to be an important predictor of the change processes necessary to improve students' physics understanding. In this study we described the process of developing and validating an instrument to measure students' beliefs in their abilities to perform essential tasks in physics and then investigated high school students' self-efficacy about physics learning and performance. Validity and reliability of PSEI were tested using various statistical techniques including the Cronbach alpha coefficient, exploratory factor analysis. The result of factor analysis supported the contention that the Physics Self-Efficacy Inventory (PSEI) was a multidimensional construct consisting of at least four dimensions: understanding and application of Physics concepts, achievement motivation, confidence for physics laboratory, confidence for Mathematics. The result showed that Kroean high schools students have low Physics self-efficacy for the all four dimensions. Therefore, researchers should focus on development of students' Physics self-efficacy. In addition, the instrument may lead to further understanding of student behavior, which in turn can facilitate the development of strategies that may increase students' aspiration to understand and study Physics. More specifically, by using the PSEI as a pre- and post-test indicator, instructors can gain insight into whether students' confidence levels increase as they engage in learning Physics, and, in addition, what type of teaching strategies are most effective in building deeper understanding of Physics concepts.where they freely exchanged opinions and feedback for constructing better collective ideas.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2003.05a
• /
• pp.62-62
• /
• 2003