• Journal of Advanced Marine Engineering and Technology
• /
• 제28권4호
• /
• pp.618-623
• /
• 2004

This paper has dealt with the heat storage characteristics of gel type micro size latent heat storage material slurry. The heat release operation to the gel type micro size latent heat storage material slurry was carried out using hot air bubbles by direct contact heat exchange. This experiment was carried out using phase change material of n-paraffin so the heat release amount is higher than cold water system. The parameters of this experiment were concentration of latent heat phase change material, height of heat release bath and inlet velocity of hot air. The main results obtained are as follows : (1) The effect of concentration of latent heat phase change material dispersed with water is very affective to the direct contact heat exchange between hot air and gel type micro size latent heat storage material slurry. (2) It is clarified that the most effective concentration of latent heat phase change material dispersed with water exists around 20mass% at this type of direct heat exchange model experiment.

• 한국지반신소재학회논문집
• /
• 제17권4호
• /
• pp.141-155
• /
• 2018

최근 국내외적으로 지하공동과 더불어 지반함몰발생 빈도수가 높아지고 있다. 따라서 지하 공동 주변부 응력이완영역의 복구에 대한 관심도 높아지고 있다. 이완영역은 지반 내에서 빈공간이 발생함에 따라 빈 공간 주변부의 지반이 원지반의 강성 및 다짐도를 잃고 느슨해진 상태로 추가적인 공동 확장 및 붕괴를 유발 할 수 있다. 따라서 본 연구에서는 공동 주변부 지반 이완영역을 보강하기 위해 팽창성 재료를 활용한 지반함몰 복구공법을 적용하고 이를 검증하고자 한다. 우선적으로 팽창성 재료의 기본 물리적 특성 및 팽창 특성을 파악하였고, 이완영역 모사 실험 장비를 제작하여 팽창성 재료의 팽창 시 이완영역에 미치는 영향을 파악하였다. 이완영역은 수치해석상 스프링계수로 모사하였다. 수치해석 변수로는 공동 체적에 대한 투입된 팽창성 재료의 부피비, 이완영역의 이완정도, 공동의 형상을 설정하였고, 이에 따른 이완영역의 전반적인 거동을 수치해석적으로 분석하였다. 해석 결과 해석 변수들은 서로 영향을 주는 인자들이였으며, 팽창성 재료가 지하공동에 삽입되었을 경우 지하공동 채움 및 이완영역 복구 정도를 확인하였다.

• 한국염색가공학회지
• /
• 제19권5호
• /
• pp.30-36
• /
• 2007

Cypermethrin-containing polyurea microcapsules were prepared by interfacial polymerization using aromatic 2,4-toluene diisocyanate(TDI) and Ethylene diamine(EDA) as wall forming materials. The effects of the protective colloids of polyvinylalcohol(PVA) and gelatin were investigated through experimentation. The mean size of the polyurea microcapsules was smaller and the surface morphology of the PVA was much smoother than gelatin. In addition the release behavior was much more controlled and better sustained. As the concentration of protective colloid increased, the wall membrane of the polyurea microcapsules became more stable, the thermal stability of the wall membrane increased, the mean particle size became smaller, and the particle distribution was more uniform. The release behavior of the core material changed according to the concentration. As the gelatin concentration was increased, a more controlled and sustained release behavior was observed. However, in the case of PVA, the increase of PVA concentration lead to a more rapid release rate.

• 한국농공학회논문집
• /
• 제57권4호
• /
• pp.31-38
• /
• 2015

This study aims to assess the effectiveness of limestone, zeolite, and crushed concrete as capping material to block the release of heavy metals (As, Cu, Cr, Ni, and Pb) and reduce the sediment oxygen demand. The efficiency of limestone, zeolite, and crushed concrete was evaluated in a reactor in which a 1-cm thick layer of capping materials was placed on the sediments collected from Inchon north harbor. Dissolved oxygen concentration and heavy metal concentration in seawater above the uncapped sediments and capping material were monitored for 17 days. The sediment oxygen demand was in the following increasing order: crushed concrete ($288.37mg/m^2{\cdot}d$) < zeolite ($428.96mg/m^2{\cdot}d$) < limestone ($904.53mg/m^2{\cdot}d$) < uncapped ($981.34mg/m^2{\cdot}d$). The capping materials could reduce the sediment oxygen demand by blocking the release of biochemical matters consuming dissolved oxygen in seawater. It was also shown that zeolite and crushed concrete could effectively block the release of Cu, Ni, and Pb but those were not effective for the interruption of As and Cr release from marine contaminated sediments.

• 대한기계학회논문집A
• /
• 제24권7호
• /
• pp.1863-1870
• /
• 2000

When an impact stress is applied on the external boundary of double cantilever beam of orthotropic material which crack length is greater than specimen hight and anistropic ratio is very high, dyna mic energy release rate is derived, and the relationship between dynamic energy release rate and crack propagating velocity is studied. Dynamic energy release rate to static energy release rate is decreased with increasment of crack propagating velocity. The relationships between dynamic energy release rate and vertical strain have a similar pattern with those between static energy release rate and vertical strain. When normalized time(Cstla) is greater than or equal to 2, dynamic energy release rate approaches to a constant value.

• Coupled systems mechanics
• /
• 제8권5호
• /
• pp.377-391
• /
• 2019

The present paper is focused on analyzing the delamination of inhomogeneous multilayered rods of circular cross-section loaded in torsion. The rods are made of concentric longitudinal layers of individual thickness and material properties. A delamination crack is located arbitrary between layers. Thus, the internal and external crack arms have circular and ring-shaped cross-sections, respectively. The layers exhibit continuous material inhomogeneity in radial direction. Besides, the material has non-linear elastic behavior. The delamination is analyzed in terms of the strain energy release rate. General solution to the strain energy release rate is derived by considering the energy balance. The solution is applied to analyze the delamination of cantilever rod. For verification, the strain energy release rate is derived also by considering the complementary strain energy.

• Advances in materials Research
• /
• 제11권1호
• /
• pp.41-57
• /
• 2022

This paper is focused on delamination analysis of a multilayered inhomogeneous viscoelastic beam subjected to linear creep under constant applied stress. The viscoelastic model that is used to treat the creep consists of consecutively connected units. Each unit consists of one spring and two dashpots. The number of units in the model is arbitrary. The modulus of elasticity of the spring in each unit changes with time. Besides, the modulii of elasticity and the coefficients of viscosity change continuously along the thickness, width and length in each layer since the material is continuously inhomogeneous in each layer of the beam. A time-dependent solution to the strain energy release rate for the delamination is derived. A time-dependent solution to the J-integral is derived too. A parametric analysis of the strain energy release rate is carried-out by applying the solution derived. The influence of various factors such as creep, material inhomogeneity, the change of the modulii of elasticity with time and the number of units in the viscoelastic model on the strain energy release rate are clarified.

• Korean Chemical Engineering Research
• /
• 제60권2호
• /
• pp.267-276
• /
• 2022

Modelling the energy release performance of energetic material combustion in closed systems is of fundamental importance for aerospace and defense application. In particular, to compensate for the disadvantage of the combustion of single energetic material and maximize the benefits, a method of combusting the mixed energetic materials is used. However, since complicated heat transfer occurs when the energetic material is combusted, it is difficult to theoretically predict the combustion performance. Here, we suggest a theoretical model to estimate the energy release performance of mixed energetic material based on the model for the combustion performance of single energetic material. To confirm the effect of parameters on the model, and to gain insights into the combustion characteristics of the energetic material, we studied parameter analysis on the reaction temperature and the characteristic time scales of energy generation and loss. To validate the model, model predictions for mixed energetic materials are compared to experimental results depending on the amount and type of energetic material. The comparison showed little difference in maximum pressure and the reliability of the model was validated. Finally, we hope that the suggested model can predict the energy release performance of single or mixed energetic material for various types of materials, as well as the energetic materials used for validation.

• 한국농공학회논문집
• /
• 제56권3호
• /
• pp.11-17
• /
• 2014

We investigated the applicability of steel slag as a capping material in order to minimize phosphorus(P) release into seawater. Steel slag is a byproduct from the iron and steel industries and the use of steel slag has some advantages in respect of both cost and environmental concern. P removal by steel slag were studied in a batch system with respect to changes in contact time and initial concentration. Kinetic adsorption data were described well by pseudo 2nd order model, indicating rate limiting step for P adsorption to steel slag is chemical sorption. Equilibrium adsorption data fitted well to Langmuir isotherm model which describes for single layer adsorption. The maximum P adsorption capacity of steel slag was 7.134 mg-P/L. Increasing the depth of steel slag produced a positive effect on interruption of P release. More than 3 cm of steel slag was effective for blocking P release and 5 cm of steel slag was recommended as the depth for capping of P contaminated marine sediments. Increasing P concentration and flow rate had a negative effect on P removal ratio. It was concluded that the steel slag has a potential capping material for blocking P release from marine sediments.

• Advances in materials Research
• /
• 제12권1호
• /
• pp.15-29
• /
• 2023

In this paper, fracture analysis of a continuously inhomogeneous arch structure with two longitudinal cracks is developed in terms of the time-dependent strain energy release rate. The arch under consideration exhibits non-linear creep behavior. The cross-section of the arch is a rectangle. The material is continuously inhomogeneous along the thickness of the cross-section. The arch is loaded by two bending moments applied at its end sections. The mechanical behavior of the material is described by using a non-linear stress-strain-time relationship. The two longitudinal cracks are located symmetrically with respect to the mid-span of the arch. Due to the symmetry, only half of the arch is considered. Time-dependent solutions to strain energy release rate are obtained by analyzing the balance of the energy. For verification, time-dependent solutions to the strain energy release rate are derived also by considering the time-dependent complementary strain energy. The evolution of the strain energy release rate with the time is analyzed. The effects of material inhomogeneity, locations of the two cracks along the thickness of the arch and the magnitude of the external loading on the time-dependent strain energy release rate are evaluated.