• Journal of the Korean Ceramic Society
• /
• v.39 no.1
• /
• pp.51-56
• /
• 2002

The effect of kind of starting materials used for a sintering additive. magnesium acetate and magnesium nitrate, on the mechanical properties of alumina sintered body made by adding 1000 ppm of the additives, respectively, was investigated. As for the alumina sintered bodies prepared from magnesium acetate and magnesium nitrate, we observed that their relative densities decreased rapidly with increasing sintering temperature 1$600^{\circ}C$. Outer layer of alumina bodies had a duplex microstructure consisting of pores and grain growth. Also the inner layer had a second phase between alumina grain boundaries. By EPMA analysis, we confirmed that the grain boundary phase was a compound containing Mg.

• Korean Journal of Materials Research
• /
• v.9 no.1
• /
• pp.51-56
• /
• 1999

The $BaTiO_3$ powders were synthesized by GNP (Glycine-Nitrate process). The powders were prepared using carbonate and alkoxide as starting materials and nitric acid was used as a solvent for starting materials as well as an oxidant for combustion. the effects of aggregates in $BaTiO_3$ powders on green densities, sintering and dielectric characteristics were investigated. When the glycine/cation molar ratio was 1.2, reactivity of self-combustion was most intensive and the degree of aggregates after calcination was low. On sintering at $1400^{\circ}C$, maximum theoretical relative density(94.99%%0 was obtained in case of 1.2 molar ratio of glycine/cation. The dielectric constant of this sintered $BaTiO_3$ was 1919.

• Journal of the Korean Ceramic Society
• /
• v.55 no.4
• /
• pp.337-343
• /
• 2018

The influence of solid loading in the slurry composition on the morphology of 3Y-TZP granules fabricated by two-fluid spray drying was investigated for solid contents varying between 30 wt% and 50 wt%. The resulting 3Y-TZP granules showed a sphere-like shape with diameters of $40-70{\mu}m$. However, a donut-like shape and a few cracks were observed on the granule surfaces fabricated using the slurry with 50 wt% solid content. The green density after cold isostatic pressing at 200 MPa was $2.1-2.2g/cm^3$, and a homogeneous fracture surface was obtained by complete destruction of granules. After sintering at $1500^{\circ}C$ for 2 h, all specimens had relative densities of 96.2 - 98.3%. With increasing solid content, the relative density decreased from 98.3% to 96.2%, but the grain size increased from $0.3{\mu}m$ to $0.6{\mu}m$. Highly sinterable zirconia granule powder could be obtained by controlling the slurry composition.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.9
• /
• pp.724-727
• /
• 2009

We have fabricated (Ba,Sr)TiO3$TiO_3$ thick films doped with various amount of ZnBO dopants (1, 3, and 5 wt%) by screen printing method on the alumina substrates, which were sintered at the temperature below $1200^{\circ}C$. With increasing the amount of ZnBO dopants, the relative dielectric permittivity of ZnBO doped (Ba,Sr)$TiO_3$ was decreased, while loss tangent was increased. 1 wt% ZnBO doped (Ba,Sr)$TiO_3$ thick film has relative dielectric permittivity of 759 at 1 MHz, while 3 and 5 wt% of ZnBO doped (Ba,Sr)$TiO_3$ thick films have 624 and 554, respectively. By introducing ZnBO dopants to the (Ba,Sr)$TiO_3$ thick films, leakage current densities were decreased. The decreased leakage current with increasing ZnBO dopants can be explained by increased density and grain size of thick film on alumina substrate. We believe this decreased leakage current density probably come from the increased grain size and increased density.

• Journal of Hydrogen and New Energy
• /
• v.16 no.1
• /
• pp.58-65
• /
• 2005

The $LaCrO_3$-dispersed Cr alloys for metallic interconnect of solid oxide fuel cell were prepared as a function of $LaCrO_3$ content in the range of 5 to 25 vol.% and were sintered at 1500$^{\circ}C$ under an Ar atmosphere with 5 vol.% $H_2$. The sintering and oxidation behaviors of these alloys were examined. The alloys indicated a good sinterability above 95% relative density at a given sintering condition, and their sintering densities is independent on $LaCrO_3$ content. The $LaCrO_3$ particles of the sintered alloys were concentrated on interfaces of Cr particles, and the size of the Cr particles increased with decreasing $LaCrO_3$ content, which is caused by inhibited grain growth of Cr particle by $LaCrO_3$ particle. The oxidation test showed all $LaCrO_3$-dispersed Cr alloys have good oxidation resistance as compared with pure Cr, which is attributed to presence of $LaCrO_3$ at the interface at which the oxidation reaction occurs rapidly. The Cr alloys with about 15 vol.% $LaCrO_3$ are very resistant to oxidation.

• Journal of the Korean Ceramic Society
• /
• v.27 no.2
• /
• pp.201-210
• /
• 1990

The mullite-15v/o ZrO2 composites were prepared by dispersing ZrO2-3m/o Y2O3 powders into the mullite matrix in order to improve the mechanical properties of the mullite. The densification and retention of t-ZrO2 in the matrix of synthetic mullite were also investigated. From IR spectroscopic analysis, the obtained amorphous SiO2-Al2O3 powder was observed to have Si-O-Al chemical bond in its structure which might result in the homogeneous mullite composition. The lattice parameter of the mullite powder calcined above 130$0^{\circ}C$ (a0=7.5468$\AA$) is nearly close to the value of stoichiometric mullite (71.8wt% Al2O3, a0=7.5456$\AA$). The sintering behavior, microstructure, flexural strength and fracture toughness of the mullite and mullite-15v/o ZrO2 composites have been studied. The mullite-15v/o ZrO2(+3m/o Y2O3) ceramics with relative densities of 96% were obtained when sintered at 1$600^{\circ}C$. The flexural strength and fractrue toughness of the composites sintered at 1$600^{\circ}C$(calcination temperature of mullite powders ; 125$0^{\circ}C$) had maximum values of 307MPa and 2.50MPa.m1/2, respectively. The fracture toughness improvement in the mullite-ZrO2 cmoposite is assumed to be resulted from the combined effect of the stress-induced phase transformation of tetragonal ZrO2 and the crack deflection due to microcracking by the monoclinic ZrO2 formation.

• Journal of Powder Materials
• /
• v.6 no.4
• /
• pp.301-306
• /
• 1999

Mechanical properties of oxide based materials could be improved by nanocomposite processing. To investigate optimum route for fabrication of nanocomposite enabling mass production, high energy ball milling and Pulse Electric Current Sintering (PECS) were adopted. By high energy ball milling, the $Al_2O_3$-based composite powder with dispersed Cu grains below 20 nm in diameter was successfully synthesized. The PECS method as a new process for powder densification has merits of improved sinterability and short sintering time at lower temperature than conventional sintering process. The relative densities of the $Al_2O_3$-5vol%Cu composites sintered at $1250^{\circ}C$ and $1300^{\circ}C$ with holding temperature of $900^{\circ}C$ were 95.4% and 95.7% respectively. Microstructures revealed that the composite consisted of the homogeneous and very fine grains of $Al_2O_3$ and Cu with diameters less than 40 nm and 20 nm respectively The composite exhibited enhanced toughness compared with monolithic $Al_2O_3$. The influence of the Cu content upon fracture toughness was discussed in terms of microstructural characteristics.

• Journal of Powder Materials
• /
• v.5 no.4
• /
• pp.286-292
• /
• 1998

Ni$_3$Al intermetallic compound has been tested as a binder phase, in order to improve the oxidation resistance and the mechanical properties of TiC-Ni cermet at a high temperature. The wettability of $Ni_3Al$ on TiC and the optimum sintering condition were investigated in TiC-(30, 40) vol% $Ni_3Al$ cermets with the sintering temperature (1380~$1430^{\circ}C$) and time (30~99 min). The results are summarized as follows: 1) Ni$_3$Al showed good wettability on TiC above 1400$^{\circ}C$ ; 2) The shrinkages of the specimens increased with the sintering temperature, the sintering time and the binder content, whereas the relative densities were decreased; 3) Any other phase did not appeared in the microstructures of all sintered cermets. The grain sizes of TiC became larger as the sintering temperature and the sintering time as well as the binder content increased; 4) The hardness of the cermets decreased with increase in the sintering temperature and the sintering time as well as the binder content; 5) The transverse-rupture strength of the cermets increased with the sintering temperature and the sintering time, whereas it decreased with the binder content.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.22-22
• /
• 2010

0.1~5.0 at% CuO doped ZnO specimens were fabricated by a commercial ceramic process and sintered at 900~$1200^{\circ}C$ for 3h in air. The relative densities were over 97% for all samples and average grain size increased with CuO doping. The defect trap levels i.e. ionization energies of defects were increased linearly with CuO contents as 0.2 eV to 0.7 eV by using admittance spectroscopy and dielectric functions. The apparent activation energies of grain boundaries were varied but in the range of 0.96~1.1 eV. Dielectric constant were increased with CuO contents and sintering temperatures.

• Journal of the Korean Ceramic Society
• /
• v.33 no.9
• /
• pp.1003-1011
• /
• 1996

Hydroxyapatite powder was synthesized by a citrate method, . Char-like precursor composed of Ca8(HPO4)2(PO4)4.5H2O (OCP) and CaCo3 was found via viscous resin-like intermediate by heating the mixed aqueous solution of Ca(NO3)2.4H2O(NH4)2HPO4 and citric acid. Resulted powder was transformed into hydroxyapatite phase by firing over 120$0^{\circ}C$-135$0^{\circ}C$ for 4 hr using the powder calcined at 90$0^{\circ}C$ for 10 hr composed of mostly single hydroxyapatite phase. The sintered densities increased with firing temperature up to 130$0^{\circ}C$ but the highest relative density was about 94% of theoritical value. indicating the presence of closed pores. The maximum 96 MPa of flexural strength was obtained at 120$0^{\circ}C$ firing but the flexural strength showed lower values over the above sintering condition. Vitro test was performed by immersing of two jointed specimens in SBF for seven days and adhesion was observed between two specimens.