• Journal of The Korean Society of Agricultural Engineers
• /
• v.54 no.5
• /
• pp.69-77
• /
• 2012

Relative density, used to express dynamics condition of sand quantitatively, is measured by RI Test, Standard Penetration Test and Cone Penetration Test. Each measurement method has demerits, which is complicated or needs a specific analysis instrument and an analysis of expert. Also the ground is in wet condition commonly because of an unsaturated zone between a saturated zone and a surface, so the behaviour of the ground has different engineering properties unlike the dry ground and it diminishes accuracy of measuring relative density. In this study, the correlation between relative density and penetration of fall cone test in dry condition and wet condition with variation of water content was analyzed and a simple measuring method for relative density was suggested. As a result, there were difference of penetration between dry sands and wet sands, the correlation between relative density and penetration showed linear expression and relative density could be measured by the linear relation.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.2
• /
• pp.5-14
• /
• 2008

Shear characteristics of quarry blasted rocks were compared using large scale direct shear tests and triaxial tests. For comparison purpose, similar test conditions were simulated as much as possible and three types of relative density (50%, 70%, 90%) were employed for the test. Results indicate that stress-strain behavior shows the same trend for two tests, but the measured shear strengths differ for the different test ms and depends on the relative density. At low relative density, the internal friction angles from direct shear test are smaller than those from triaxial tests. However, at high relative density, this phenomenon is reversed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.1358-1366
• /
• 2006

In order to study the effects of shell contents on the liquefaction resistance of the shelly sand, NGI cyclic simple shear tests were performed for the shelly sands with shell contents of 0%, 5%, 10%, 20% and 30% under the effective vertical stress of 50kPa, 100kPa and 150kPa for 40% and 55% of relative density, respectively. Cyclic simple shear test results showed that for the low effective vertical stress, liquefaction resistance increased rapidly with the increase of shell contents in both 40% and 55% relative density. On the other hand, for the high effective vertical stress, the liquefaction resistance increased slightly in 40% relative density whereas the resistance was almost same in 55% relative density. Liquefaction resistance decreased with increasing effective vertical stress for both 40% and 55% relative density. In the same effective vertical stress and shell contents, liquefaction resistance increased with the increase of relative density of sands.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1994.09a
• /
• pp.265-272
• /
• 1994

The relative density seems to be important as a factor of controlling the physical properties in the case of cohesionless soil ground as sand. Therefore, the study is more important about the method for reappearing the same relative density when the specimen of shearing test is to be produced or the model test of ground is to be made. In this study, the apparatus making use of the multiple sieving pluviation method - one of the reappearance of relative density - could be made. Using this apparatus, tests were practiced varying the factors such as the size of sieve mesh and the number of sieve, the amount of falling discharge, the falling height etc. about the standard sand in Jumunjin and Hadong sand. When laboratory test is performed by the cohensionless soil , it presents the method for reappearing of the relative density in field.

• Journal of the Korean Society of Safety
• /
• v.16 no.3
• /
• pp.99-105
• /
• 2001

This paper presents results km a series of model tests oil vertically loaded single piles to compare the behaviors of H and pipe piles under the same ground condition. The aims of this paper were to compare the bearing capacity of H-pile md pipe piles under in the same ground condition and to estimate the effect of gravity acceleration and relative soil density. Relative density of soil were made to be 40%, 80% and embedded length of pile on sand was increased by 10, 12, 14, 16 times of the diameter of pile, respectively. As a results of test series, allowable load of H-pile is from 6.4% to 18.2% larger than allowable load of pipe pile in relative density 80% and from 9.1% to 39.4% larger than allowable load of pipe pile in relative density 40%. As a results of numerical analysis, we were predicted behaviour of stress-displacement of pile with model test. In the case of relative density 80% and 40%, bearing capacity of H pile represent from 17.74% to 18.6% larger than allowable load of pipe pile.

• Geomechanics and Engineering
• /
• v.38 no.2
• /
• pp.165-177
• /
• 2024

Liquefaction phenomenon refers to a phenomenon in which excess pore water pressure occurs when a dynamic load such as an earthquake is rapidly applied to a loose sandy soil ground where the ground is saturated, and the ground loses effective stress and becomes liquid. The laboratory repetition test for liquefaction evaluation can be performed through a repeated triaxial compression test and a repeated shear test. In this regard, this study attempted to evaluate the effects of the relative density of sand on the liquefaction resistance strength according to particle size distribution using repeated triaxial compression tests, and additional experimental verification using numerical analysis was conducted to overcome the limitations of experimental equipment. As a result of the experiment, it was confirmed that the liquefaction resistance strength increased as the relative density increased regardless of the classification of soil, and the liquefaction resistance strength of the SP sample close to SW was quite high. As a result of numerical analysis, it was confirmed that the liquefaction resistance strength increased as the confining pressure increased under the same relative density, and the liquefaction resistance strength did not decrease below a certain limit even though the confining pressure was significantly reduced at a relatively low relative density. This is judged to be due to a change in confining pressure according to the depth of the ground. As a result of analyzing the liquefaction resistance strength according to the frequency range, it was confirmed that there was no significant difference from the laboratory experiment results in the basic range of 0.1 to 1.0 Hz.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.3
• /
• pp.13-17
• /
• 2013

Determination of geotechnical characteristics of soil is either to use the field samples to measure the characteristics of soil through laboratory test or measuring the characteristics directly in the field. Field test can be derived similar value by considering characteristics of site and laboratory test can be confirmed the characteristic of soil by testing with field samples. This article describes relative density as the measure of compaction for cohesionless soils and presents several simple and mathematical relationships to help engineers estimate needed parameters for relative density calculations. The main purpose of this research is to investigate possible correlations between coefficient of uniformity, coefficient of curvature, maximum and minimum void ratio, mean grain size. Results show a linear relationship between the minimum and maximum void ratios and a power function relationship between coefficient of uniformity and the limiting void ratios. Void ratio range, which is the difference between the maximum and minimum void ratios, appeared to be log normally distributed but showed no simple mathematical fit to the data. these results were shown to help engineers estimate needed parameters for relative density calculations.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.1142-1150
• /
• 2010

An elementary particle of bottom ash is similar to fine sand. So which expected from replace expensive sand. Therefore, this study conducts cyclic triaxial test and a resonant test using relative density, which is obtained from a relative density test of bottom ash and standard sand. Also, it compares antiseismic characteristics of bottom ash and standard sand in order to analyze the possibility of commercial use as a construction material.

• Geomechanics and Engineering
• /
• v.17 no.2
• /
• pp.145-156
• /
• 2019

Since behaviors of loose, dense, silty sands vary under seismic loading, understanding the liquefaction mechanism of sandy soils continues to be an important challenges of geotechnical earthquake engineering. In this study, 36 deformation controlled cyclic simple shear tests were performed and the liquefaction potential of the sands was investigated using three different relative densities (40, 55, 70%), four different effective stresses (25, 50, 100, 150 kPa) and three different shear strain amplitudes (2, 3.5, 5%) by using energy based approach. Experiments revealed the relationship between per unit volume dissipated energy with effective stress, relative density and shear strain. The dissipate energy per unit volume was much less affected by shear strain than effective stress and relative density. In other words, the dissipated energy is strongly dependent on relative density and effective stress. These results show that the dissipated energy per unit volume is very useful and may contain the non-uniform loading conditions of the earthquake spectrum. When multiple regression analysis is performed on experiment results, a relationship is proposed that gives liquefaction energy of sandy soils depending on relative density and effective stress parameters.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.6
• /
• pp.63-79
• /
• 2011

In this study relative density tests of bottom ash and standard sand were carried out. And cyclic triaxial tests for samples with the relative density of 40%, 55%, and 70% were carried out on the basis of the test results. Cyclic triaxial tests were also conducted for fines content with 55% relative density. Residual samples were divided into No.40, No.60, No.60, and No.100, and No.200. In order to avoid crashing that can happen when compaction of the sample is initiated, bottom ash was crushed using the a compact mold. In consideration of the crushing characteristics of each residual samples, the fragmentation rate increased up to 30%, which led to the adjustment of fine-grained amount to 10%, 20%, and 30%. Through the repative triaxial test in accordance with the relative density, resistant characteristics of the liquefaction of bottom ash was analyzed. Test results show that, crushing strength of bottom ash was smaller than that of standard sand, resulting in different liquefaction behavior characteristics. And we could find fines content with maximum resistant characteristics of the liquefaction.