• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.8
• /
• pp.113-119
• /
• 2000

There are two major factors which affect the cam design : the pressure angle and the radius of curvature, Cam shape will have an instantaneous radius of curvature at every point. Even though the design constraint of the pressure angle has been satisfied the follower may still not complete the desired contact motion. If the radius of the follower roller is larger than the concave(negative) radius on the cam it occurs the gap between the cam and the follower roller at the contact point. And also if the curvature of the pitch curve of the cam is too sharp the cam profile may be undercut. This paper proposes a new approach which uses the relative velocity of the follower roller parallel to the tangent line at the contact point on the cam surface for determining the pressure angle and the relative acceeration for determining the radius of curvature.

• Geomechanics and Engineering
• /
• v.38 no.2
• /
• pp.165-177
• /
• 2024

Liquefaction phenomenon refers to a phenomenon in which excess pore water pressure occurs when a dynamic load such as an earthquake is rapidly applied to a loose sandy soil ground where the ground is saturated, and the ground loses effective stress and becomes liquid. The laboratory repetition test for liquefaction evaluation can be performed through a repeated triaxial compression test and a repeated shear test. In this regard, this study attempted to evaluate the effects of the relative density of sand on the liquefaction resistance strength according to particle size distribution using repeated triaxial compression tests, and additional experimental verification using numerical analysis was conducted to overcome the limitations of experimental equipment. As a result of the experiment, it was confirmed that the liquefaction resistance strength increased as the relative density increased regardless of the classification of soil, and the liquefaction resistance strength of the SP sample close to SW was quite high. As a result of numerical analysis, it was confirmed that the liquefaction resistance strength increased as the confining pressure increased under the same relative density, and the liquefaction resistance strength did not decrease below a certain limit even though the confining pressure was significantly reduced at a relatively low relative density. This is judged to be due to a change in confining pressure according to the depth of the ground. As a result of analyzing the liquefaction resistance strength according to the frequency range, it was confirmed that there was no significant difference from the laboratory experiment results in the basic range of 0.1 to 1.0 Hz.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.768-773
• /
• 2004

When a gas expands through a convergent nozzle in which the ratio of the ambient to the stagnation pressures is higher than that of the critical one, the issuing jet from the nozzle is underexpanded. If a flat plate is placed normal to the jet at a certain distance from the nozzle, a detached shock wave is formed at a region between the nozzle exit and the plate. In general, supersonic moist air jet technologies with nonequilibrium condensation are very often applied to industrial manufacturing processes. In spite of the importance in major characteristics of the supersonic moist air jets impinging to a solid body, its qualitative characteristics can not even know. In the present study, the effect of the nonequilibrium condensation on the underexpanded moist air jet impinging on a vertical flat plate is investigated experimentally. Flow visualization and impact pressure measurement are performed for various relative humidities and flat plate positions. The obtained results show the plate shock and Mach disk are dependent on the nozzle pressure ratio and the relative humidity, but for a given nozzle pressure ratio, the diameters of the plate shock and Mach disk depend on the stagnation relative humidity. The impact pressure deviation from the flow of without condensation is large, as the relative stagnation humidity increases.

• Journal of Korean Academy of Nursing
• /
• v.30 no.4
• /
• pp.948-955
• /
• 2000

This study was done to compare the difference of obesity index(waist-hip ratio, body fat, body mass index, relative body weight), blood pressure and serum lipids in abdominal obesity and non abdominal in both men and women. Abdominal and non abdominal obesity was divided into waist-hip ratio above 0.85 in women and 0.95 in men. The subjects were 412 adults (age range 40-59), who had regular health examinations between 1996 to 1997 at the S-Hospital in Seoul. The data were analyzed using ANCOVA (for adjusted for age) and Pearson correlation coefficient. The results were as follows: 1. 39.9% of men and 42.5% of women had abdominal obesity. The average age group of abdominal obesity was 50.8 which is older than the non abdominal obesity group(48.0). 2. After they were adjusted for age, the group of men who have abdominal obesity had higher levels in body fat, body mass index, relative body weight, blood pressure, total cholesterol, LDL- cholesterol and triglyceride than the group of non abdominal obesity group. The group of women with abdominal obesity had higer levels in body fat, body mass index, relative body weight , blood pressure and triglyceride than the group of non abdominal obesity. 3. In the group of non abdominal obesity, the waist-hip ratio was significantly correlated to body fat, body mass index, relative body weight, blood pressure and serum lipids the group of abdominal obesity in men and women.

• Journal of agricultural medicine and community health
• /
• v.18 no.1
• /
• pp.65-75
• /
• 1993

This study was conducted to compare the frequency and to find epidemiologic characteristics of the diseases by analyzing the results of routine first health examination for partial healthy public officials. The total number of the examined was 1.128(876 male, 252 female) The results were as follow; 1. The prevalence rate of suspicious disease was liver disease 5.9% hypertension 5.4%, hyperlipemic disease 3.8%, pulmonary tuberculosis 1.2% by order. 2. The mean systolic blood pressure and diastolic blood pressure showed increasing trend by age increasing. The mean of blood pressure in man was rather higher than that in woman. 3. The prevalence rate of suspicious borderline hypertension increased by aging. And the distribution of high cholesterol group and over than overweight group increased by aging. 4. In male, significant relation among age, systolic blood pressure, diastolic blood pressure, relative body weight was found. And significant relation between total cholesterol level and relative body weight was found. In female, age and relative body weight was related to systolic blood pressure, diastolic blood pressure and total cholesterol level. 5. According to the retrospective follow-up for those who had suspicious disease, correspondence rate of results was 5.2% in circulatory disease and 1.5% in liver disease.

• The Korean Journal of Ecology
• /
• v.15 no.1
• /
• pp.47-58
• /
• 1992

This study is to investigate the change of the seasonal patterns of relative water relations parameters by the pressure-volume curves in pinus koraiensis needles. The osmotic potentials at full water saturated(Ψ0, sat) and at incipient plasmolysis(Ψ0, tlp) increased in growing season, while decreased in non-growing season. The maximum bulk modulus of elasticity(Emax), relative water content(RWCTLP), and relativefree water content(FWCtlp) at incipient plasmolysis in non-growing season were higher than these of growing season. The maximum pressure potential(Ψp, max) varied from 1.16 to 2.18MPa, torgor index(TI) varied from 3.1 to 4.7. The osmole number(Ns/dw) and symplastic water (Vo/DW) were variable seasonally. The maximum water content(Vt/DW) and apoplastic water(AW) were relatively high in early growing stage, and then decreased to needle aging. The pressure potential(Ψp) and water potential(Ψ) in winter needles were rapidly decreased with decreasing of relative water content. The matric potential occupied over 10 percent of water potential with less than-2.0 MPa.

• Journal of Korea Foundry Society
• /
• v.24 no.1
• /
• pp.26-33
• /
• 2004

The pressure of the mold flux acting on the meniscus shell was investigated through the coupling analysis of heat transfer in the mold and fluid flow in the flux caused by the mold oscillation. Finite element method was employed to solve the conservation equation associated with appropriate boundary conditions. As reported by previous workers, the axial pressure is positive on the negative strip time and negative on the positive strip time. A maximum pressure is predicted toward the top of the meniscus shell which has the thin shell arid a maximum value is in proportion to the relative mold oscillation velocity. The relative mold oscillation velocity was changed by the effect of meniscus level fluctuation. Therefore the pressure of the mold flux acting on the meniscus shell was different each cycle of the mold oscillation due to the irregularity of relative mold oscillation velocity.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.1
• /
• pp.80-91
• /
• 2009

In this study, a prediction theory for specific noise that is the overall characteristic of the fan has been proposed. This theory is based on total pressure prediction and broadband noise prediction. The specific noises of two forward curved fans with different number of blades were predicted. The flow around the impeller having 120 blades (MF120) was more biased at a certain positions than the impeller with 40 blades (MF40). An effective domain of the energy conversion of MF40 has extended overall than MF120. The total pressure was affected by the slip factor and pressure loss caused by the vortex flow. The suppression of a major pressure drop by the vortex flow and expansion of the effective domain for energy conversion contributed to an increase in the total pressure of MF40 at the design point. The position of maximum relative velocity was different for each fan. The relative velocity of MF120 was less than that of MF40 due to the deviation angle. The specific noise of MF120 was 2.7 dB less than that of MF40 due to the difference in internal flow. It has been quantitatively estimated that the deceleration in the relative velocity contributed to the improvement in the overall performance.

• Journal of the Korean Ceramic Society
• /
• v.53 no.1
• /
• pp.99-104
• /
• 2016

High purity Si-C (99.999%) powder prepared by mechanical alloying was added to a commercial SiC powder as a sintering additive. Reaction bonded silicon carbide balls and jars with high purity (99.98%) were used for the mechanical alloying. As a result, the purity of the sintered Si-C was higher than 99.99%. When sintered at $2200^{\circ}C$ under 50 MPa pressure for 1 h, SiC containing 10 wt% of high purity Si-C showed a relative density of 95.3%, similar to the relative density of commercial SiC (95%). However, the relative density of SiC decreased to 90.6% without the additive when the applied pressure decreased to 40 MPa. In contrast, the relative density was nearly unaffected by the decrease of the pressure when using the Si-C additive. Therefore, the addition of Si-C powder promoted the densification of SiC above $2000^{\circ}C$ under 40 MPa pressure.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.34 no.3
• /
• pp.33-42
• /
• 1992

The shear strength of cohesionless Soils results from particle-to-particle friction and structural resistance by interlocking. And, the shear strength of soils is subjected to vary depending on the internal states and external condtions. If the volume change occurring in the soils and stress-strain relationships under the internal and external changes can accrurately he described, it is possible to predict the behaviors of soils. To accomplish these objectives a series of drained triaxial compression tests and isotropic compression test was performed on the Banwol sand at different relative densities ranging from 20% to 80% and different confining pressures ranging from 0.4kgf/cm$^2$ to l2kgf/cm$^2$. The results and main conclusions of the study are summarized as follows; 1.When the relative density or the confining pressure is increased, the maximum deviator stress is increased. The ratio of the maximum deviator stress and the confining pressure is linearly proportional to the relative density. 2.It is observed that the dilatancy depends not only upon its relative density but also the confining stress, and that the maximum deviator stress is obtained after the diatancy occurs. 3.The volume of sands undergoes initial contraction prior to the dilatancy occurred by strain softening. The dilatancy rate eventually approaches the critical state or a constant volume. 4.At lower strains, Poisson's ratio approaches a certain minimum value regadless of the state of materials. At larger strains, however, the ratio is increased as the relative density is increased. 5.It is observed that the modulus of elasticity is linearly proportional to the relative density and the pressure. 6.When the relative density is increased, the friction angle of sands is linearly increased. 7.When the relative density is increased, the expansion index and the compression index are linearly decreased, and the ratio of the two is about 1/3.