• 한국강구조학회 논문집
• /
• 제20권1호
• /
• pp.81-92
• /
• 2008

일반적인 강구조물의 연결은 강절(rigid) 또는 활절(hinge)로 취급되고 있으나 실제 강구조물은 연결부위에서 부재간의 상대적인회전이 허용됨으로 인해 부분강절(semi-rigid)의 특성을 갖게 된다. 본 연구에서는 부분강절을 회전스프링으로 가정하여 부재 단부에 적용시킨 평면 뼈대구조물의 엄밀한 접선강도행렬을 유도하고 이를 다시 탄성강도행렬과 기하학적 강도행렬로 분리 유도함으로써 부분강절을 갖는 평면 뼈대구조물의 안정성해석을 위한 일반화된 해석방법을 제시하고자 한다. 이를 위하여, 보-기둥부재의 좌굴조건을 만족시키는 처짐함수로부터 안정함수(stability function)를 유도하고, 횡변위(sway)를 고려한 힘-변위관계와 적합조건을 고려하여 정확한 접선강도행렬을 제시하였다. 본 연구의 타당성과 실용성 제고를 위해 두 가지 방법에 의한 수치해석프로그램을 개발하였고 다양한 해석예제를 통해, 타 연구자 해석 결과와 비교하고 부분강절이 구조물의 좌굴강도에 미치는 영향에 대하여 조사한다.

• Structural Engineering and Mechanics
• /
• 제76권4호
• /
• pp.465-477
• /
• 2020

This paper presents an investigation on the dynamic behavior of SRC columns with built-in cross-shaped steels under impact load. Seven 1/2 scaled SRC specimens were subjected to low-speed impact by a gravity drop hammer test system. Three main parameters, including the lateral impact height, the axial compression ratios and the stirrup spacing, were considered in the response analysis of the specimens. The failure mode, deformation, the absorbed energy of columns, as well as impact loads are discussed. The results are mainly characterized by bending-shear failure, meanwhile specimens can maintain an acceptable integrity. More than 33% of the input impact energy is dissipated, which demonstrates its excellent impact resistance. As the impact height increases, the flexural cracks and shear cracks observed on the surface of specimens were denser and wider. The recorded time-history of impact force and mid-span displacement confirmed the three stages of relative movement between the hammer and the column. Additionally, the displacements had a notable delay compared to the rapid changes observed in the measured impact load. The deflection of the mid-span did not exceed 5.90mm while the impact load reached peak value. The impact resistance of the specimen can be improved by proper design for stirrup ratios and increasing the axial load. However, the cracking and spalling of the concrete cover at the impact point was obvious with the increasing in stiffness.

• Elastomers and Composites
• /
• 제43권1호
• /
• pp.25-30
• /
• 2008

자동차 부싱은 차체로 전달되는 하중을 줄여주는 역할을 하는 자동차 현가장치의 주요 부품으로 바깥쪽 슬리브와 안쪽의 축 사이에서 가운데가 비어 있는 실린더의 형상을 가진다. 차축에 작용되는 힘과 모멘트에 대한 부싱의 상대변위 및 변형각도는 점탄성 성질을 나타내며, 부싱에서 힘과 모멘트와 이에 대한 변위와 변형각도의 관계는 다물체 동역학 시뮬레이션에 매우 중요하다. 본 연구는 자동차 부싱의 회전방향 모드에 대한 모멘트와 변형각도의 점탄성 관계를 변형각도에 의존하는 모멘트 완화함수를 통하여 부싱모델을 완성하였으며, 완성된 점탄성 부싱 모델은 회전방향 모드에 대한 실험값과 비교하여 검증하였다.

• Steel and Composite Structures
• /
• 제30권6호
• /
• pp.535-550
• /
• 2019

Prestressed concrete (PC) bridges using corrugated steel webbing have emerged as one of the most promising forms of steel-concrete composite bridge. However, their long-term behavior is not well understood, especially in the case of large-span bridges. In order to study the time-dependent performance, a large three-span PC bridge with corrugated steel webbing was compared to a similar conventional PC bridge to examine their respective time-dependent characteristics. In addition, a three-dimensional finite element method with step-by-step time integration that takes into account cantilever construction procedures was used to predict long-term behaviors such as deflection, stress distribution and prestressing loss. These predictions were based upon four well-established empirical creep prediction models. PC bridges with a corrugated steel web were observed to have a better long-term performance relative to conventional PC bridges. In particular, it is noted that the pre-cambering for PC bridges with a corrugated steel web could be smaller than that of conventional PC bridges. The ratio of side-to-mid span has great influence on the long-term deformation of PC bridges with a corrugated steel web, and it is suggested that the design value should be between 0.4 and 0.6. However, the different creep prediction models still showed a weak homogeneity, thus, the further experimental research and the development of health monitoring systems are required to further progress our understanding of the long-term behavior of PC bridges with corrugated steel webbing.

• 한국지반공학회논문집
• /
• 제25권11호
• /
• pp.5-15
• /
• 2009

낙동강 델타지역 퇴적토의 동적변형특성에 관한 데이터베이스 구축의 일환으로서 낙동강 모래의 변형특성을 조사하였다. 시험시료는 낙동강 중류와 하구언 인근에서 채취하였으며, 시편은 건조낙사법에 의하여 성형하였다. 성형된 시험시편으로 공진주/비듦전단시험을 수행하였고, 시험시 다양한 영향요소(구속압, 상대밀도, 변형률크기, 반복하중횟수)를 조사하였다. 시험결과는 Ramberg-Osgood 모델과 Modified Hyperbolic 모델을 적용하여 정규화전단계수 감소곡선과 감쇠비곡선으로 나타내었으며, 기존문헌에서 제시하는 곡선들과 비교한 결과 약간의 차이를 보였으나, 전반적으로 유사한 경향을 보여주었다. 본 RC/TS 실험으로부터의 결과는 향후 낙동델타지역의 사질토지반의 동적응답 거동을 분석할 때 매우 중요한 자료로 쓰일 것으로 판단된다.

• 대한토목학회논문집
• /
• 제28권1C호
• /
• pp.41-51
• /
• 2008

본 논문은 말뚝 및 기초지반의 강성이 수평재하말뚝의 거동에 미치는 영향을 알아보고자 주문진 표준사와 김해점토를 기초지반으로 수평재하말뚝에 대한 실내실험을 실시하였다. 또한 실험 결과를 바탕으로 영향계수를 정량화 할 수 있는 경험식을 산정하였다. 말뚝과 지반의 강성을 고려하기 위하여 길이가 다른 3개의 알루미늄 모형말뚝을 제작하였으며 이를 사질토와 점성토 지반에 설치한 후 기초지반의 상대밀도(사질토 지반) 및 비배수전단강도(점성토 지반)를 변화시켜가며 수평재하 실내실험을 수행하였다. 실험을 통하여 산정된 p-y 곡선의 초기기울기는 사질토와 점성토 지반 모두에서 깊이와 말뚝-지반의 강성에 비례하였으나 점성토 지반의 경우 사질토 지반에 비하여 깊이에 따른 초기기울기의 증가율이 작은 경향을 나타내었다. 또한 극한 지반반력의 경우 모든 지반 조건에서 수평지반반력계수와 유사하게 깊이와 지반강성에 비례하여 증가하였으나 말뚝 강성에 대한 영향은 적게 나타났다. 이와 같은 특성을 고려하여 본 논문에서는 p-y 곡선의 초기기울기 산정 식을 실험결과와 가장 유사한 형태를 지니는 쌍곡선으로 지반 조건에 따라 제시하였으며 제안된 식을 기존의 연구 및 현장재하시험과 비교하여 제안 식의 적용성을 검증하였다.

• 대한토목학회논문집
• /
• 제29권4A호
• /
• pp.299-305
• /
• 2009

본 연구에서는 철도교의 세로보 절취부에서의 피로균열 발생 원인을 연구하기 위하여 실제로 피로균열이 발생한 철도교를 연구대상으로 실물크기의 가로보-세로보 바닥틀 모형을 제작하고 실내실험을 수행하였다. 연구 결과 세로보 상부절취부에서의 피로균열 발생원인은 세로보의 단부에서 발생하는 부모멘트에 의한 상부절취부 복부판의 면내응력의 반복적 작용 결과이고, 하부절취부에서의 피로균열 발생 원인은 세로보 단부의 고정단에 대한 하부절취부 복부판의 상대적 면외변형에 의해 발생하는 면외응력의 반복적 작용 결과라는 결론을 얻었다.

• Geomechanics and Engineering
• /
• 제31권2호
• /
• pp.167-181
• /
• 2022

Soil liquefaction has been one of the most important concerns in geotechnical earthquake engineering in recent years, due to its damages to structures and its destructive effects. The cyclic liquefaction of silty sands, in particular, remains of great interest for both research and application. Although many factors are known that affect the liquefaction resistance of sands, the effect of fine grain content is perhaps one of the most studied and still controversial. In this study, 48 deformation-controlled cyclic simple shear tests were performed on BS and CS silt samples mixed with 5%, 15% and 30% by weight of Krk085, Krk042 and Krk025 sands in constant-volume conditions to determine the liquefaction potential of silty sands. The tests were carried out at 30% and 50% relative density and under 100 kPa effective stress. The results revealed that the liquefaction potential of silty sand increases with increasing average particle size ratio (D_50sand / d_50silt) of the mixture for a fixed silt content. Furthermore, for identical base sand, the liquefaction potentials of coarse grained sands increase with increasing silt content, while the respective potentials of fine grained sands generally decrease. However, this situation may vary depending on the silt grain structure and is affected by the nature of the fine grains. In addition, the variation of the void ratio interval was shown to provide a good intuition in determining the liquefaction potentials of silty sands, while the intergranular void ratio alone does not constitute a criterion for determining the liquefaction potentials of silty sands.

• Smart Structures and Systems
• /
• 제30권5호
• /
• pp.479-500
• /
• 2022

In this study, a new type of isolation bearing is proposed by combining S-shaped steel plate dampers (SSDs) with a spherical steel bearing, and the seismic control effect of a five-span standard high-speed railway bridge is investigated. The advantages of the proposed S-shaped steel damping friction bearing (SSDFB) are that it cannot only lengthen the structural periods, dissipate the seismic energy, but also prevent bridge unseating due to the restraint effectiveness of SSDs in the large relative displacements between the girders and piers. This study first presents a detailed description and working principle of the SSDFB. Then, mechanical modeling of the SSDFB was derived to fundamentally define its cyclic behavior and obtain key mechanical parameters. The numerical model of the SSDFB's critical component SSD was verified by comparing it with the experimental results. After that, parameter studies of the dimensions and number of SSDs, the friction coefficient, and the gap length of the SSDFBs were conducted. Finally, the longitudinal seismic responses of the bridge with SSDFBs were compared with the bridge with spherical bearing and spherical bearing with strengthened shear keys. The results showed that the SSDFB can not only significantly mitigate the shear force responses and residual displacement in bridge substructures but also can effectively reduce girder displacement and prevent bridge unseating, at a cost of inelastic deformation of the SSDs, which is easy to replace. In conclusion, the SSDFB is expected to be a cost-effective option with both multi-stage energy dissipation and restraint capacity, making it particularly suitable for seismic isolation application to high-speed railway bridges.

• Wind and Structures
• /
• 제37권4호
• /
• pp.289-302
• /
• 2023

Insulating glass units (IGUs) have been widely used in buildings in recent years due to their superior thermal insulation performance. However, because of the panel reciprocating motion and fatigue deterioration of sealants under long-term wind loads, many IGUs have the problem of early failure of watertight properties in real usage. This study aimed to propose a statistical method for wind-induced deflection of IGU panels during the whole life service period, for further precise analysis of the accumulated fatigue damage at the sealed part of the edge bond. By the estimation of the wind occurrence regularity based on wind pressure return period, the events of each wind speed interval during the whole life were obtained for the IGUs at 50m height in Beijing, which are in good agreement with the measured data. Also, the wind-induced deflection analysis method of IGUs based on the formula of airspace coefficient was proposed and verified as an improvement of the original stiffness distribution method with the average relative error compared to the test being about 3% or less. Combining the two methods above, the deformation of the outer and inner panes under wind loads during 30 years was precisely calculated, and the deflection and stress state at selected locations were obtained finally. The results show that the compression displacement at the secondary sealant under the maximum wind pressure is close to 0.3mm (strain 2.5%), and the IGUs are in tens of thousands of times the low amplitude tensile-compression cycle and several times to dozens of times the relatively high amplitude tensile-compression cycle environment. The approach proposed in this paper provides a basis for subsequent studies on the durability of IGUs and the wind-resistant behaviors of curtain wall structures.