DOI QR코드

DOI QR Code

Dynamic behavior of SRC columns with built-in cross-shaped steels subjected to lateral impact

  • Liu, Yanhua (School of Urban Construction, Yangtze University) ;
  • Zeng, Lei (School of Urban Construction, Yangtze University) ;
  • Liu, Changjun (School of Urban Construction, Yangtze University) ;
  • Mo, Jinxu (School of Urban Construction, Yangtze University) ;
  • Chen, Buqing (School of Urban Construction, Yangtze University)
  • Received : 2020.01.04
  • Accepted : 2020.07.08
  • Published : 2020.11.25

Abstract

This paper presents an investigation on the dynamic behavior of SRC columns with built-in cross-shaped steels under impact load. Seven 1/2 scaled SRC specimens were subjected to low-speed impact by a gravity drop hammer test system. Three main parameters, including the lateral impact height, the axial compression ratios and the stirrup spacing, were considered in the response analysis of the specimens. The failure mode, deformation, the absorbed energy of columns, as well as impact loads are discussed. The results are mainly characterized by bending-shear failure, meanwhile specimens can maintain an acceptable integrity. More than 33% of the input impact energy is dissipated, which demonstrates its excellent impact resistance. As the impact height increases, the flexural cracks and shear cracks observed on the surface of specimens were denser and wider. The recorded time-history of impact force and mid-span displacement confirmed the three stages of relative movement between the hammer and the column. Additionally, the displacements had a notable delay compared to the rapid changes observed in the measured impact load. The deflection of the mid-span did not exceed 5.90mm while the impact load reached peak value. The impact resistance of the specimen can be improved by proper design for stirrup ratios and increasing the axial load. However, the cracking and spalling of the concrete cover at the impact point was obvious with the increasing in stiffness.

Keywords

Acknowledgement

The research is supported by the National Natural Science Foundation of China (Grant number 51978078) and the Science Foundation of Hubei Province of China (Grant number 2016CFB604). The authors also would like to thanks for every staff of the civil engineering test center of Yangtze University participated in this study.

References

  1. Al-Rifaie, A., Guan, Z.W., Jones, S.W. and Wang, Q. (2017), "Lateral impact response of end-plate beam-column connections", Eng. Struct., 151, 221-234. https://doi.org/10.1016/j.engstruct.2017.08.026
  2. Al-Thairy, H. and Wang, Y.C. (2011), "A numerical study of the behaviour and failure modes of axially compressed steel columns subjected to transverse impact", Int. J. Impact Eng., 38(8-9),732-744. https://doi.org/10.1016/j.ijimpeng.2011.03.005
  3. Briaud, J.L. (2007) Introduction to Soil Erosion, Texas A&M University, State of Texas, ST, USA.
  4. Cai, J., Ye, J.B., Chen, Q.J., Liu, X. and Wang, Y.Q. (2018), "Dynamic behaviour of axially-loaded RC columns under horizontal impact loading", Eng. Struct., 168, 684-697. https://doi.org/10.1016/j.engstruct.2018.04.095.
  5. Demartino, C., Wu, J.G. and Xiao, Y. (2017), "Response of shear-deficient reinforced circular RC columns under lateral impact loading", Int. J. Impact Eng., 109, 196-213. https://doi.org/10.1016/j.ijimpeng.2017.06.011.
  6. Do, T. V., Pham, T. M. and Hao, H. (2019), "Impact force profile and failure classification of reinforced concrete bridge columns against vehicle impact", Eng. Struct., 183, 443-458. https://doi.org/10.1016/j.engstruct.2019.01.040.
  7. Du, G.F., Andjelic, A., Li, Z., Lei, Z. and Bie, X. (2018), "Residual Axial Bearing Capacity of Concrete-Filled Circular Steel Tubular Columns (CFCSTCs) after Transverse Impact", Appl. Sci., 8(5), 793. https://doi.org/10.3390/app8050793.
  8. Du, G.F., Li, Z. and Song, G.B. (2018), "A PVDF-Basd Sensor for Internal Stress Monitoring of a Concrete-Filled Steel Tubular (CFST) Column Subject to Impact Loads", Sens, 18(6), 1682. https://doi.org/10.3390/s18061682.
  9. Echevarria, A., Zaghi, A. E., Chiarito, V., Christenson, R. and Woodson, S. (2016), "Experimental Comparison of the Performance and Residual Capacity of CFFT and RC Bridge Columns Subjected to Blasts", J. Bridge Eng., 21(1), 04015026. https://doi.org/10.1061/(asce)be.1943-5592.0000762
  10. Gholipour, G., Zhang, C. and Mousavi, A. A. (2018), "Effects of axial load on nonlinear response of RC columns subjected to lateral impact load: Ship-pier collision", Eng. Fail. Anal., 91, 397-418. https://doi.org/10.1016/j.engfailanal.2018.04.055.
  11. Huang, L., Gao, C., Yan, L., Yu, T. and Kasal, B. (2018), "Experimental and numerical studies of CFRP tube and steel spiral dual-confined concrete composite columns under axial impact loading", Compos. B: Eng., 152, 193-208. https://doi.org/10.1016/j.compositesb.2018.07.008
  12. Huynh, L., Foster, S., Valipour, H. and Randall, R. (2015), "High strength and reactive powder concrete columns subjected to impact: Experimental investigation", Constr. Build. Mater, 78, 153-171. http://dx.doi.org/10.1016/j.conbuildmat.2015.01.026
  13. Hou, C.C. and Han, L.H. (2018), "Life-cycle performance of deteriorated concrete-filled steel tubular (CFST) structures subject to lateral impact", Thin-Walled Struct., 132, 362-374. https://doi.org/10.1016/j.tws.2018.08.025.
  14. Huang, W., Zhou, Z. and Liu, J. (2017), "Analytical deformation characteristics and shear capacity of SRC-RC transfer columns", J. Constr. Steel. Res., 138, 692-700. https://doi.org/10.1016/j.jcsr.2017.08.024
  15. Ji, X., Cheng, Y., Leong, T. and Cui, Y. (2019), "Seismic behavior and strength capacity of steel coupling beam-to-SRC wall joints", Eng. Struct., 201, 109820. https://doi.org/10.1016/j.engstruct.2019.109820.
  16. Kubiak, T., Gliszczynski, A. and Krygier, M. (2019), "Impact damage tolerance of laminate short columns subjected to uniform compression-Experimental investigation", Compos. Struct., 226, 111222. https://doi.org/10.1016/j.compstruct.2019.111222.
  17. Liu, B., Fan, W., Guo, W., Chen, B. and Liu, R. (2017), "Experimental investigation and improved FE modeling of axially-loaded circular RC columns under lateral impact loading", Eng. Struct., 152, 619-642. https://doi.org/10.1016/j.engstruct.2017.09.009
  18. Mo, J.X., Zeng, L., Liu, Y.H., Ma, L.L., Liu, C.J. and Xiang, S. (2020), "Mechanical properties and damping capacity of polypropylene fiber reinforced concrete modified by rubber powder", Constr. Build. Mater, 242. https://doi.org/10.1016/j.conbuildmat.2020.118111
  19. Partheepan G and S. Venkata Si K. (2019), "FE modelling of low velocity impact on RC and prestressed RC slabs", Struct. Eng. Mech., 71(5), 515. https://doi.org/10.12989/sem.2019.71.5.515
  20. Qi B, Kong, Q., Qian, H., Patil, D., Lim, I., Li, M., Liu, D. and Song, G. (2018), "Study of impact da-mage in PVA-ECC beam under low-velocity impact loading using piezoceramic transducers and PVDF thin-film transducers", Sens., 18(2), 671. https://doi.org/10.3390/s18020671
  21. Song G, Olmi C, and Gu H. (2007), "An overheight vehicle-bridge collision monitoring system using piezoelectric transducers"; Smart Mater. Struct., 16(2), 462. https://doi.org/10.1088/0964-1726/16/2/026
  22. Thai, D.K. and Kim, S.E. (2015), "Numerical simulation of reinforced concrete slabs under missile impact", Struct. Eng. Mech., 53(3), 455-479. https://doi.org/10.12989/sem.2015.53.3.455
  23. Tuan, Ngo. and Priyan Mendis. (2009),"Modelling the dynamic response and failure modes of reinforced concrete structures subjected to blast and impact loading", Struct. Eng. Mech., 32(2), 269-282. https://doi.org/10.12989/sem.2009.32.2.269
  24. Thilakarathna, H. M. I., Thambiratnam, D. P., Dhanasekar, M. and Perera, N. (2010), "Numerical simulation of axially loaded concrete columns under transverse impact and vulnerability assessment", Int. J. Impact Eng., 37(11), 1100-1112. https://doi.org/10.1016/j.ijimpeng.2010.06.003
  25. Wu, K.C., Li, B. and Tsai, K.C. (2011), "Residual axial compression capacity of localized blast-damaged RC columns", Int. J. Impact Eng., 38(1), 29-40. https://doi:10.1016/j.ijimpeng.2010.09.002.
  26. Wang, W and Morgenthal, G. (2017), "Dynamic analyses of square RC pier column subjected to barge impact using efficient models", Eng. Struct., 151, 20-32. http://dx.doi.org/10.1016/j.engstruct.2017.08.003.
  27. Wei, J., Li, J. and Wu, C. (2019), "An experimental and numerical study of reinforced conventional concrete and ultra-high performance concrete columns under lateral impact loads", Eng. Struct., 201, 109822. https://doi.org/10.1016/j.engstruct.2019.109822.
  28. Wang, Y., Qian, X., Liew, J. Y. R. and Zhang, M.H. (2015), "Impact of cement composite filled steel tubes: An experimental, numerical and theoretical treatise", Thin-Walled Struct., 87, 76-88. https://doi.org/10.1016/j.tws.2014.11.007.
  29. Xiao, Y.F., Zeng, L., Cui, Z.K., Jin, S.Q. and Chen, Y.G. (2017), "Experimental and analytical performance evaluation of steel beam to concrete-encased composite column with unsymmetrical steel section joints", Steel. Compos. Struct., 23(1), 17-29. http://doi.org/10.12989/scs.2017.23.1.017.
  30. Xiang, S., Zeng L., Liu Y.H., Mo, J.H., Ma, L.L., Zhang, J.C. and Chen, J. (2020), "Experimental study on the dynamic behavior of T-shaped steel reinforced concrete columns under impact loading", Eng. Struct., 208, 110307. http://doi.org/10.1016/j.engstruct.2020.110307.
  31. Xu, C.H., Zeng L., Zhou, Q., Tu, X. and Wu, Y. (2015), "Cyclic performance of concrete-encased composite columns with T-shaped steel sections", Int. J. Civ. Eng., 13(4), 456-467.
  32. Xue, Y., Yang, Y. and Yu, Y. (2019), "Cyclic behavior of part-ially precast steel reinforced concrete short columns: Experiment and theoretical analysis", Eng. Struct., 199, 109658. https://doi.org/10.1016/j.engstruct.2019.109658.
  33. Xiao, Y.F., Zeng, L., Chen, Y.G., Du, G.F., Zhang, J.C. and Chen, J. (2019) "Seismic fragility ana-lysis of concrete-encased frame-reinforced concrete core tube hybrid structure based on quasistatic cyclic test", Struct. Design Tall Spec. Build., e1665. https://doi.org/10.1002/tal.1665.
  34. Xiong, F., Wang, D. and Yin, S. (2018), "Optimization analysis of novel foam-filled elliptical columns under multiple oblique impact loading", Mater. Des., 156, 198-214. https://doi.org/10.1016/j.matdes.2018.06.057.
  35. Yang, B., Wang, H., Yang, Y., Kang, S.B., Zhou, X.H. and Wang, L. (2018), "Numerical study of rigid steel beam-column joints under impact loading", J. Constr. Steel. Res., 147, 62-73. https://doi.org/10.1016/j.jcsr.2018.04.004.
  36. Zeng, L., Parvasi, S. M., Kong, Q., Huo, L., Lim, I., Li, M. and Song, G. (2015), "Bond slip detection of concrete-encased composite structure using shear wave based active sensing approach", Smart. Mater. Struct., 24(12), 125026. https://doi.org/10.1088/0964-1726/24/12/125026.
  37. Zeng, L., Ren, W.T., Zou, Z.T., Chen, Y.G., Xie, W. and Li, X.J. (2019), "Experimental study on seismic behavior of frame structures composed of concrete encased columns with L-shaped steel section and steel beams", EQ. Struct., 16(1), 97-107. http://doi.org/10.12989/eas.2019.16.1.097.
  38. Zeng, L., Xiao, Y., Chen, Y., Jin, S., Xie, W. and Li, X. (2017), "Seismic Damage Evaluation of Concrete-Encased Steel Frame-Reinforced Concrete Core Tube Buildings Based on Dynamic Characteristics", Appl. Sci., 7(4), 314. https://doi.org/10.3390/app7040314.
  39. Zhu, J., Ho, S.C.M., Kong, Q., Patil, D., Mo, Y.L. and Song, G. (2017), "Estimation of impact location on concrete column", Smart Mater. Struct., 26(5), 055037. https://10.1088/1361-665X/aa6768.
  40. Zhang, X., Hao, H. and Li, C. (2016), "Experimental Investigation of the Response of Precast Segmental Columns Subjected to Impact Loading", Int. J. Impact Eng., 95, 105-124. http://dx.doi.org/10.1016/j.ijimpeng.2016.05.005.