• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.5
• /
• pp.328-335
• /
• 2010

The purpose of this study is to make an analysis of influence on the cooling capacity and COP of a desiccant cooling system with a regenerative evaporative cooler when a direct evaporative cooler was applied to the inlet of regeneration process of this system. We used cycle simulation in order to analyze the performance of this system. From the cycle simulation, we knew that the optimal rotation time of desiccant rotor was between 160s and 220s and hardly ever affected cooling capacity of desiccant cooling system when this system was operated at the outdoor air condition of $35^{\circ}$ and 40% RH and low regeneration temperature of $60^{\circ}$. Also there was optimal area ratio of regeneration to dehumidification between 0.7 and 1.0. Our results showed that it had a small effect on the system’s cooling capacity to install direct evaporative cooler at the inlet of regeneration process.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.3
• /
• pp.102-110
• /
• 2004

A design code validated against the thermal analysis results of CFD and published RTE code for a regeneratively cooled combustion chamber has been developed. The major function of the code is to predict the regenerative cooling performance and stress of the chamber wall. Adopted are the empirical correlation for the evaluation of the heat transfer coefficient of hot gas and coolant, and theoretical formula for the fin effect of the channel rib. The hot-gas-side wall temperature from the present code shows 100 K difference at most compared to RTE results. It shows less than 10 % difference for the heat flux thrall through the chamber wall and hot-gas-side convective heat transfer coefficient. The major cause of the wall temperature difference is due to the underestimation of the fin effect of the channel rib.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.3
• /
• pp.271-278
• /
• 2008

A study has been conducted on the bulging process of liquid rocket engine nozzle which is essential to the manufacturing regenerative cooling combustion chamber. Mechanical properties of the material used for the bulging were experimentally obtained by tension tests. Deformation of the bulged nozzle was confirmed by a structural analysis. The developed bulging process and the deformation analysis result were confirmed by manufacturing of the bulged nozzle specimens and the bulging test. There has been a bulging failure among 7 bulged specimens due to the necking of the material. The cause of necking was investigated by comparing microstructure of the material. The investigation has revealed grain size of the material has considerable effect on the occurrence of the necking.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.194-197
• /
• 2007

The dome stretching and tension test have been made to obtain a forming limit curve(FLC) for the copper alloy which is used for manufacturing the regenerative cooling chamber. For experimental survey of the forming limit curve, we have used in-plane tension specimen to obtain tension-compression strain state and also out of plane specimen to obtain tension-tension strain state through dome stretching test. All specimens are divided into longitudinal and radial direction specimens by the manufacturing method. The test results shows that in tension-tension region, copper alloy possesses a maximum major strain of 62.3% and maximum minor strain of 58.6%. In the tension-compression region, maximum major strain is 60.5% and maximum minor strain is 25.8%.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.1
• /
• pp.35-44
• /
• 2011

Mathematical modelling for liquid rocket engine(LRE) main components were conducted to predict the dynamic characteristics when the LRE operates at the transient condition, which include engine start up, shut down, or thrust control. Propellant feeding system is composed of fuel and oxidizer feeding components except for regenerative cooling channel for the fuel circuit. Components modeling of pump, pipe, orifice, control valve, regenerative cooling channel and injector was serially made. Hydraulic tests of scale down component were made in order to validate modelling components. The mathematical models of engine components were integrated into LRE transient simulation program in concomitant with experimental validation.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.2
• /
• pp.44-49
• /
• 2011

A study of the fatigue life of copper alloy which was used in inner jacket of regenerative cooling chamber of liquid rocket engine has been performed. Generally used life prediction methods -original universal slopes method, modified universal slopes method, Mitchell's method, B$\"{a}$umel and Seeger's method, and Ong's method- have been used for predicting the fatigue data. It was found that the novel life prediction method which was modified from Ong's method was suggested since almost all data have not been predicted well with the widely used methods. The suggested modified Ong's method predicted well within 3X scatterbands.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.89-92
• /
• 2010

A study about the fatigue life of copper alloy which is used in inner jacket of regenerative cooling chamber of liquid rocket engine has been performed. Generally used life prediction methods-original universal slopes method, modified universal slopes method, Mitchell's method, Baumel and Seeger's method, and Ong's method-have been used for predicting the fatigue data. It was found that the novel life prediction method which is modified from Ong's method was suggested since almost all data have not been predicted well with the widely used methods. The suggested modified Ong's method predicted well within 3X scatterbands.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.6
• /
• pp.88-95
• /
• 2014

Spinning process to inner wall has been applied for reducing the weight of regenerative cooling chamber of liquid propellent rocket engine. The fractures of the blanks of cylinder part and nozzle throat part have been observed during spinning processes. In order to overcome the problem, the mandrel and the blank shape have been modified, and the inner wall was successfully manufactured through the modifications. The manufactured spinning prototype of nozzle throat part was successfully bulged without cracking and necking, and it was confirmed to secure sufficient formability necessary for fabricating thrust chamber.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.198-204
• /
• 2004

Using liquefied natural gas as a fuel, water, natural gas and liquefied natural gas-cooled firing tests were conducted. With the viewpoint of characteristic velocity, and specific impulse, the effect of OF mixture ratio and fuel inlet temperature into a combustion chamber were analyzed. OF mixture ratio and fuel inlet temperature into a combustion chamber have great influence on the performance. Characteristic velocity and theoretical specific impulse attain the maximum value at 0.72~0.75 and 0.75 of OF mixture ratio, respectively. Engine performance has a tendency to increase, proportional to fuel inlet temperature into a combustion chamber affected by the regenerative cooling.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.3
• /
• pp.38-44
• /
• 2000

In general liquid rocket nozzles are protected from hot combustion gas by regenerative cooling techniques. But due to the complexity of the cooling system, it causes increase of system cost and frequently source of the system malfunction. Recently, instead of regenerative cooing, ablative material are used to protect combustion chamber wall and nozzle. To determine the nozzle material erosion rate and erosion shape, more than 500 hot fire test were performed by using 100 lb thrust experimental liquid rocket. Test variable were propellant feed sequence, injector, position of igniter and liquid oxygen supply temperature.