• Journal of the Korean Ceramic Society
• /
• v.29 no.1
• /
• pp.15-22
• /
• 1992

The reason for permanent shrinking of recycled castable refractories from alumino-silicate waste refractories was investigated and the method to control shrinking is suggested in order to increase maximum service termperature. The porosity of castable refractories with waste material as large aggregate decreases after heat treatment because the porosity of waste refractories is greater than the of green material, in which CaO around large aggregate penetrates into aggregate and promotes liquid phase sintering. The shrinking of recycled castable refractories resulted in the decrease in porosity can be controled by addition of green kaolin chamotte as large aggregate. The shrinking of recycled castable refractories caused by the differences in densities of mineral phases before and after heat treatment can be controled by addition of kyanite. The use of green kaolin chamotte and kyanite increases the service temperature of recycled castable refractories up to 1500$^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1141-1149
• /
• 2003

Refractory industry in technologically advanced countries has long been on gradual decline due to leveled-off steel production and decreasing unit consumption of refractories for steel. Notable technological achievements by refractory industry that contributed significantly to steel production are briefly reviewed covering from blast furnace, basic oxygen furnace to continuous casting. Future possibility to revitalize the refractory industry is discussed on the basis of the review, taking into account opportunities available in environment and energy related sector of industries.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.1
• /
• pp.27-31
• /
• 2015

The degradation of refractories can be caused by erosion, friction of abrasive particles, as well as by corrosion by molten slag in the gasification reactors. There was little knowledge about the erosion of refractories so far. The castable refractories of which the maximum applying temperature of 1300 and $1500^{\circ}C$ were abraded using SiC particles varying the incidence angles. It was revealed that the maximum abrasion was occurred at the incidence angle of $60{\sim}75^{\circ}$ not at $90^{\circ}$ and thought that the porosity of the refractories was the principle factor.

• Journal of the Korean Ceramic Society
• /
• v.36 no.8
• /
• pp.876-885
• /
• 1999

In order to develop high performance basic dam block for tundish vessel in steel-making binders and additives on hydration and thermal characteristics of magnesiz castable refractories were studied. Crack initiation and propagation in cement bonded magnesia castables due to slaking of magnesia clinker at drying process were suppressed by using spinel clinker instead of magnesia powder. In case of Na2O$.$2CaO$.$P2O5(NC2P) bonded castable crack initiation due to slaking of magnesia clinker did not occur but bending strength at high temperature was low. Mechanical properties of NC2P bonded castable refractories at high temperature were improved by using magnesia clinker that contains low SiO2 contents.

• Journal of the Korean Ceramic Society
• /
• v.56 no.1
• /
• pp.77-83
• /
• 2019

MgO-C refractories are used in basic furnaces and steel ladles due to their many desirable properties, such as excellent thermal shock resistance via low thermal expansion, and high thermal conductivity. However, the mechanical and thermal properties of the refractory continuously deteriorate by spalling phenomena and pore generation due to the oxidation of graphite, used as a carbon source, indicating that the characteristics and performance of MgO-C refractories need to be improved by using a new material or composition. In this study, the use of a Hertzian indentation test as a method for determining the damage and fracture behavior of an MgO-C refractory is described. The results highlight that Hertzain indentation tests can be one of the important evaluation tools for quasi-plastic damage accumulation of MgO-C refractories during falling process of scrap metal.

• Journal of Environmental Health Sciences
• /
• v.21 no.4
• /
• pp.17-23
• /
• 1995

As a basic experiment to develope biological pretreatment proces~ in water treatment, the experiments on biodegradability and isothermal adsorption of activated carbon were performed on refractories such as humic acid, $NH_3-N$, phenol and ABS which caused the problems in drinking water treatment. Also, the treatabilities on humic acid were examined in the continuous flow type reactors. The removal efficiencies of humic acid, $NH_3-N$, phenol and ABS in the biodegradable experiments for 5 days were 20.1%, 73.4%, 91.7% and 97.5%, respectively. In the isothermal adsorption test of refractories on activated carbon to be used as a media in the continuous flow type reactors, ABS and phenol are adsorbed easily, but humic acid and $NH_3-N$ are difficult to be done. The removal efficiencies of humic acid in granular activated carbon(GAC) reactor were about 7-8% higher than in biological activated carbon(BAC) reactor. The removal efficiencies of humic acid in biological fluidized bed(BFB) reactor were about 30% in GAC media, but were almost zero in sea sand media.

• The Korean Journal of Ceramics
• /
• v.4 no.4
• /
• pp.345-351
• /
• 1998

Thermal shock resistance of $Al_2O_3$- and Fe-$Al_2TiO_5$-based Castable Refractories was studied using a central heating technique. Ring type specimens, 10mm thick and 20 and 100mm inner and outer diameters, respectively, were rapidly heated on the internal surface of the centre hole using a high power electrical heating element. The temperature field was measured experimentally and modelled using finite element analysis (FEA). The thermal stress field was also modelled using FEA. A radial notch was introduced to the ring specimens to enable calculation of the thermal stress intensity factors (SIF). A special LVDT device was incorporated in the thermal shock tester to monitor crack mouth opening displacement (COD). The thermal shock fracture initiation and crack propagation behaviour of the castable refractories were ascertained using the COD measurements and the fracture mechanics analysis data.

• Journal of the Korean Ceramic Society
• /
• v.27 no.7
• /
• pp.877-882
• /
• 1990

Effects of metallic Al powder addition on basic and thermal properties of castable refractories were investigated. Generally, low grade prooperties were obtained by metallic Al powder addition with the increase of temperature, comparing with those of non-addition of Al powder. Especially, Al addtion showed severe shrinkage, corrosiion and low strength above 1000$^{\circ}C$. As a result of Al addition, lower strength of and higher corrosion resistance were shown for 2% addition, but it was reversed for above 4% addition. It was found that Al addition was excellent in the explosive spalling test regardless of Al quantity.

• Journal of the Korean Ceramic Society
• /
• v.23 no.1
• /
• pp.51-59
• /
• 1986

It was the first time the MgO-C brick was developed for the lining materials in the hot spots in electric are furnace in 1972. MgO-C brick is high registant to thermal and structural spalling. Futhermore for the reason that carbon is hard to react with slag and MgO is high fireproof MgO-C brick shows a high corrosion registance to slag attack compared with conventional basic refractories. Owing to their excellent properties the use of MgO-C refractories are being developed widely in the field of shaped refractories and even in that of monolithic refractories. In this paper the oxidation of carbon the infiltration of slag into the brick texture and effects of additions were investigated. The results obtained were as follows : 1) The use of fused MgO-clinker and high purity carbon as raw materials increased the corosion registance and hot modulus of rupture of MgO-C brick. 2) As the oxidation reaction of the carbon proceeded the slag infiltrated into the brick texture. And then the slag components reacted with the MgO grains and formed low melting point compounds particulary CaO.MgO.$SiO_2$ and 3CaO.MgO.$2SiO_2$ that resulted in the wear of the brick. 3) It is recongnized the Al, Si, $B_3C$ effects on the oxidation registant properties of MgO-C brick by contribu-ting to the decrease of permeability according to the formation of $Al_4C_3$, SiC, $B_2O_3$ and the decrease of open pores relating to the formation of MgO.Al2O3, $SiO_2$, 3MgO.$B_2O_3$ at the decarbonized layer.

• Resources Recycling
• /
• v.12 no.3
• /
• pp.46-53
• /
• 2003

Recycling of aluminum dross is an important issue in the secondary aluminum industries. In this study, aluminum dross generated in the domestic secondary aluminum industry was processed to use it as raw material for producing alumina refractories. Sample dross was classified according to its size. The dross smaller than 1 mm was leached with sodium hydroxide solution to extract the remained aluminum from the dross into the solution. and then aluminum hydroxide precipitate was recovered from the leach liquor. The waste residue in the leaching was washed, dried and roasted. Most remained metallic components in the residue was changed into oxide through the processes. The roasted dross was made into alumina castable refractories by mixing with aggregates and a binder. Bending strength of the tested castable specimen was over $25\;kg/\textrm{m}^2$ and compressive strength over $80\;kg/\textrm{cm}^2$, which satisfied the Korean Standard value respectively. From the results, it was suggested that this process could be applicable to recycling of aluminum dross.