• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.5-8
• /
• 1997

A study on the electrical conduction characteristics of the ultrathin organic films is one of the important factors for the development of molecular electronic devices. The Langmuir- Blodgett(LB) technique has recently been attracted interest as a method of the deposition ultrathin films. We hate fabricated N-docosyl N\`-methyl viologen-diTCNQ(DMVT) anion radical LB film and investigated the molecular orientation and electrical conduction characteristics. We have measured infrared transmission-reflection spectra. The alkyl chain is found to he well-ordered with the tilt angle of 13$^{\circ}$ with respect to the substrate surface normal and the TCNQ plane is tilted at 76$^{\circ}$ the surface normal. In ESR spectrum, we confirmed that a half-amplitude linewidth is clearly dependent on the incident angle, which indicates conducting species change. The in-plane conductivity of 31 lagers is approximately 1.33$\times$10$^{-6}$ S/cm. The ohmic behaviour was observed below 0.6 V, when current-voltage(I-V) characteristics was measured verically.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.12
• /
• pp.1036-1043
• /
• 2016

In this paper, an analysis about the elevation angle accuracy degradation of an APAR(Airport Precision Approach Radar) due to the multi-path effect using a phased array antenna was performed. An APAR installed around a runway of airport will be continuously affected in a runway surface of the fixed environment. In this paper, an analysis about the elevation angle accuracy degradation of APAR due to the multi-path effect of runway surface was conducted through a calculation of monopluse slope and sum/difference beam pattern analysis of array antenna. Also, a difference pattern for monopulse to minimize this degradation was optimized in an appropriate configuration to improve a elevation angle accuracy. Finally, a degree of improvement of elevation angle accuracy was confirmed by calculating a monopulse slope including the ground reflection after applying optimized difference patterns of array antenna.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.3
• /
• pp.365-372
• /
• 2013

The multibeam surveillance radar is a state-of-art of 3D radar technology. It applies the stacked beams realized by a digital beamformer. In this paper, a hybrid compensation technique on elevation angle errors for low elevation angle targets over the sea in multipath radar environments is proposed. The proposed method can be applied to stacked beam radars. Double null algorithm based on maximum likelihood method in 3-D beamspace domain works well unless the phase difference between the two rays(direct and specular path) is close to $0^{\circ}$ and the magnitude of reflection coefficient is close to 0. To overcome these problems, we propose a hybrid compensation technique which uses the selective double null algorithm and the beam-ratio compensation technique for low-elevation errors on a log scale. Results of computer simulation show that the proposed method outperform conventional monopulse method and double null algorithm only under various multipath environments.

• Tunnel and Underground Space
• /
• v.12 no.4
• /
• pp.268-276
• /
• 2002

In this study, a 3D coordinate measurement system equipped with a laser displacement meter for digitizing rock joint surface was established and the digitized data were used to calculate several roughness parameters. The parameters used in this study were micro avenge inclination $angle(i_{ave})$, average slope of joint $asperity(SL_{ ave})$, root mean square of $i-angle(i_{rms})$, standard deviation of height(SDH), standard deviation of $i-angle(SD_i)$, roughness profile $index(R_P)$, and fractal dimension(D). The relationships between the roughness parameters based on the digitzation of the surface profile were analyzed. Since the measured value varied according to the degree of reflection and the variation of colors at the measuring point, rock joint surface was painted in white to minimize the influence of the surface conditions. The comparison of the measured values and roughness parameters before and after painting revealed the better consequence from measurement on the painted surfaces. Also, effect of measuring interval was studied. As measured interval was increased, roughness parameters were exponentially decreased. The incremental sequence of degree of decrease was $SDH\; i_{ave},\; i_{rms},\; SD_i,\;and\; R_ p-1$. As a result of comparison of parameters from pin-type measurement system and laser type measurement system, all value of parameters were higher when laser-type measurement system was used, except SDH.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1824-1827
• /
• 2003

The sheet metal shearing process is normally used in the precision elements such as semi-conductor components. In precision elements, burrs usually reduce the quality of machined parts and cause interference, jamming and misalignment during assembly procedures and because of their sharpness, they can be safety hazard to personnel. Furthermore, not only burrs are hard to predict and avoid, but also deburring, the process of removing burrs, is time-consuming and costly. In order to get the burr-free parts, therefore, we developed the precise burr measuring system using the laser. The laser burr measuring system consists of the laser probe, the photo detector, the achromatic doublet lens, and the rotary ＆ the X-Y table. In previous reports, we used simple vertical measuring method. But, as we used relatively bigger laser spot diameter and had the limited reflection angle, it was difficult to obtain the precise measuring results. So called, the spot size effect makes the profile of burr measured distorted and the burr height measured smaller. By introducing the novel laser measuring method which employing the achromatic lens system and the tilting mechanism, we could make the spot size smaller and get the appropriate beam direction angle. Through the experiments, the accuracy of the developed system is proved. The burr height measured during the punching process can be used for automatic deburring and in-situ aligning.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.11
• /
• pp.863-869
• /
• 2008

This paper investigated the new calibration algorithm of a straight-type five-hole pressure probe for measuring three-dimensional flow velocity components. This new calibration algorithm was used for velocity data reduction from the calibration map and based on the combination of a look-up, a binary search algorithm and a geometry transformation including the translation and reflection of nodes in a calibration map. The calibration map was expanded up to the application angle, ${\pm}55^{\circ}$ of a probe. This velocity data reduction method showed a perfect performance without any kind of interpolating errors in calculating yaw and pitch angles from the calibration map. Moreover, when it was applied to an actual flow field including a swirling flow, a good result came out on the whole.

• Journal of Fashion Business
• /
• v.23 no.6
• /
• pp.27-36
• /
• 2019

This study aimed to analyze the color differences by warp direction of textile mosaics by focusing on two representative textile wallcovering types, woven and string. Mosaics made of string can be expressed as having three-dimensionality based on color differences resulting from the warp direction of the string. String wallcoverings, unlike woven or non-woven wallcoverings, only have vertically oriented warp lamination on the backing paper without weft, and therefore, the reflection and backing color can be expressed differently depending on the angle of the mosaic. In this study, two identical wallcoverings were manufactured using the same materials but using different textile types, woven and string. The wallcoverings underwent die-cutting by each angle and were deployed in cube form. The analysis was based on ISO 5631-1:2015. The color difference between the two wallcoverings, woven and string, was shown as ΔE* 9.29. Based on the standard deviation of the color difference for each mosaic angle, woven ranged from ΔE* 0.09 to 0.94 and string ranged from ΔE* 1.92 to 3.74, showing a larger color difference. Thus, using the color differences of string to create a mosaic wallcovering improved dimensionality.

• The Journal of the Acoustical Society of Korea
• /
• v.22 no.8
• /
• pp.652-659
• /
• 2003

High-frequency(40∼120 kHz) reflection loss measurements on the water-sandy sediment with a flat interface were conducted in a water tank for various grazing angles. The water tank(5×5×5 m) was filled with a 0.5 m-thick-flat bottom of 0.5ø-mean-grain-size sand. Reflection losses, which were experimentally obtained as a function of grazing angle and frequency, were compared with the forward loss model, APL-UW model (Mourad & Jackson, 1989). For frequencies below 60 kHz, the observed losses well agree with the reflection loss model, however, in cases for frequencies above 70 kHz, the observed losses are greater by 2∼3 dB than the model results. The model calculation, which does not fully account for the vertical scale of roughness due to grain size, produce less bottom losses compared to the observations that correspond to large roughness based on the Rayleigh parameter in the wave scattering theory. In conclusion, for the same grain-size-sediment, as frequencies increase, the grainsize becomes the scale of roughness that could be very large for the frequencies above 70 kHz. Therefore, although the sea bottom was flat, we have to consider the frequency dependence of an effect of roughness within confidential interval of grain size distribution in reflection loss model.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.25 no.6
• /
• pp.349-356
• /
• 2013

The purpose of this study is to review and overcome the limits of the existing design wave model applied to such waters as those located inside bays or near islands where the impact of wind influenced waves are more dominant, due to the nature of topographic isolation, than the influence of direct waves coming from the open sea. Although the existing model for an inside bay design wave is excellent for considering wind factors and very adaptable to topographically complicated areas compared to other models, it is difficult to show the wave diffractions and reflections caused by large scale structures or topographic features in the region. The study examined the various methods capable of taking into account wave diffraction, the angle of wave reflection, and changes in water depth. As a result of applying the modified design wave model to the target situation (inside bay or near island areas), it was found that the reliability of the design wave height around marine structures was improved, compared to the existing models. Therefore, it is fair to predict that the new model could provide more accurate design waves in the design of marine structures.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.6
• /
• pp.63-70
• /
• 2012

This paper discussed on the directive gain improvement method of the U-type ultra wide-band(UWB) planar patch antenna model with CPW feeding. For directive gain improvement, the U-type printed patch antenna model with CPW feeding is reconstructed as a microstrip structure by adding a reflection plane with aperture slot. The reflection coefficient of the reconstructed antenna is less than -6.5 dB(VSWR < 3.3) to the characteristic impedance of $50.08{\Omega}$ and showed the directive radiation patterns with the directive gain of 7.5 dBi ~ 10.1 dBi, the front-back ratio of 17.8 dB ~ 28.7 dB and the range of -3dB radiation angle over ${\pm}30^{\circ}$ to the main beam direction of ${\theta}=0^{\circ}$.