• Geophysics and Geophysical Exploration
• /
• v.9 no.4
• /
• pp.279-290
• /
• 2006

The borehole radar methods used to tunnel detection are mainly classified into borehole radar reflection, directional antenna, crosshole scanning, and radar tomography methods. In this study, we have investigated the feasibility and limitation of each method to tunnel detection through case studies. In the borehole radar reflection data, there were much more clear diffraction signals of the upper wings than lower wings of the hyperbolas reflected from the tunnel, and their upper and lower wings were spreaded out to more than 10m higher and lower traces from the peaks of the hyperbolas. As the ratio of borehole diameter to antenna length increases, the ringing gets stronger on the data due to the increase in the impedance mismatching between antennas and water in the boreholes. It is also found that the reflection signals from the tunnel could be enhanced using the optimal offset distance between transmitter and receiver antennas. Nevertheless, the borehole radar reflection data could not provide directional information of the reflectors in the subsurface. Direction finding antenna system had a advantage to take a three dimensional location of a tunnel with only one borehole survey even though the cost is still very high and it required very high expertise. The data from crosshole scanning could be a good indicator for tunnel detection and it could give more reliable result when the borehole radar reflection survey is carried out together. The images of the subsurface also can be reconstructed using travel time tomography which could provide the physical property of the medium and would be effective for imaging the underground structure such as tunnels. Based on the results described above, we suggest a cost-effective field procedure for detection of a tunnel using borehole radar techniques; borehole radar reflection survey using dipole antenna can firstly be applied to pick up anomalous regions within the borehole, and crosshole scanning or reflection survey using directional antenna can then be applied only to the anomalous regions to detect the tunnel.

• The Korean Journal of Air & Space Law and Policy
• /
• v.28 no.2
• /
• pp.97-115
• /
• 2013

The world-wide principal criteria of aircraft operations is ICAO Annex 6. Operations of Aircraft. Among ICAO Annex 6, Part I is for International Commercial Air Transport - Aeroplanes and it assumes major part of civil aviation. ICAO has been providing Contracting States with SARPs(Standards and Recommended Practices) and monitor each State's reflection degree into their domestic air law, so-called USOAP(Universal Safety Oversight Audit Program). Current ICAO USOAP is Snap-shot method, but it will be changed to USOAP-CMA method from the year of 2013. ICAO USOAP results have overall effects on national aviation industry such as routes, insurance, airlines cooperation and so forth. Low grades of results attract international attention and that leads to flag carrier's operation stoppage, route restriction, airlines cooperation restriction, insurance increase directly or indirectly. Thus it is important to get excellent grades in ICAO USOAP and to maintain confidence. Our government ranked top to get 98.89 grades in 2008 ICAO USOAP but after 2008 the revised provisions have not been reflected sufficiently into our air law. So I would like to grip reflection ratio of ICAO Annex 6 Part I into our domestic air law by using the most updated revised edition on this paper. Together I would like to suggest alternatives for the non-reflected and partially reflected.

• Journal of Korean Elementary Science Education
• /
• v.41 no.4
• /
• pp.754-770
• /
• 2022

For teachers, noticing refers to paying attention to something, indicating they interpret it and how they are willing to react to it in the context of their own instruction. Analysis of noticing features enables us to understand the overall characteristics of the teacher's lesson design, practice, and reflection, which are core agents in the educational design and implementation. This can also be taken to be the basis of education design for competency reinforcement for teachers. Therefore, in this study, the characteristics of noticing shown in teachers' reflections after class design and demonstration were identified. For this purpose, the self-reflection journals of 106 elementary pre-service teachers enrolled in the College of Education in Gangwon-do were analyzed. In particular, the journals were gathered that were written after the demonstration dealing with the change of gas volume by temperature in science class. After designing a noticing analysis frame consisting of the five dimensions 'agent', 'stage', 'topic', 'focus', and 'stance', the frequency and ratio of noticing by each dimension's components were derived. The frequency and ratio of noticing for the dimension of 'focus' were analyzed for the dimensions of 'stage' and 'topic'. The results of the study were as follows. For the dimension of 'agent', the frequency of teacher and student was the highest, and for the dimension of 'stage', inquiry activity was the highest. For the 'topic' dimension, class design according to the teaching strategy appeared most frequently, and in the 'focus' dimension, the cases that did not specify the goal of the class and the competencies to be achieved by the students appeared most frequently. In the 'stance' dimension, description showed the highest frequency. From the analysis of how the 'focus' changes according to the 'stage' and 'topic', it was found that a characteristic focus appeared for each component of the dimension. From these results, the implications of the noticing characteristics of pre-service teachers for the design and implementation of teacher education were discussed.

• Journal of radiological science and technology
• /
• v.22 no.1
• /
• pp.43-47
• /
• 1999

In order to obtain effective utilization of intensifying screens[$CaWO_4(W),\;Gd_2O_2S:Tb(Gd)$, BaFCl : Eu(Ba)] over the diagnostic radiology range, we calculated absorption coefficient (${\mu}$), absorption efficiency (${\eta}_{\alpha}$) and absorbed energy ratio(R) and analyzed effects of these properties on X-ray image, finally concluded as below. Regardless of presence of contrast media, absorption coefficient of Gd the highest and decreased with increase of thickness and kVp. Absorption efficiency related with absorbance of fluorescent materials showed the highest value for the Gd, and discontinuous points exhibited at around $80{\sim}90\;kVp$ and $90{\sim}100kVp$ for the Ba and the Gd, respectively. Furthermore, the absorbed energy ratio(R) correspond to contrast of reflection showed the largest value for the W in the absence of contrast media, and for the Gd in the case of the existence of it, and the ratio was decreased with increasing of incident energy. Owing to these properties, we assumed that it was more preferable to use rare earth type intensifying screen for the radiography using in the C.M.(I, Ba), while in the general radiography, $CaWO_4$ intensifying screen was applicable.

• Journal of Korean Ophthalmic Optics Society
• /
• v.9 no.2
• /
• pp.417-421
• /
• 2004

We can see that two images of reflection are observed on the surface of a ophthalmic lens. These are the image reflected from front surface and back surface of lens, respectively. The reflective image shows to be affect by surface refractive power of front and back surface of lens. Total refractive power of lens is calculated by refractive power of front and back surface of lens. Accordingly, the ratio of image on the lens surface is able to measure refractive power of ophthalmic lens without helping of the lensmeter. The ratio of two reflective image measured on the lens surface is compared with the calculated ratio by the power measurement.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.6
• /
• pp.446-450
• /
• 2013

Growth mechanism of GS-MBE(Gas source-Molecular Beam Epitaxy) has been investigated. We observed that the growth rate of GaN films is changing from 520 nm/h to 440 nm/h by the variation of V/III ratio under nitrogen-rich growth condition. It was explained that the amount of hydrogen on the growth front varies by the ammonia flow, and gallium hydrides are generated on the surface by a reaction of hydrogen and gallium, resultantly the amount of gallium supplying is changing along with the $NH_3$ flow. Reflection high energy electron diffraction (RHEED) observation was used to confirm the N-rich condition. The crystal quality of GaN was estimated by photoluminescence (PL) and X-ray diffraction (XRD).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.7
• /
• pp.662-666
• /
• 2005

Silicon nitride $(SiN_x)$ film is a promising material for anti-reflection coating and passivation of multicrystalline silicon (me-Si) solar cells. In this work, a plasma-enhanced chemical vapor deposition (PECVD) system with batch-type reactor tube was used to prepare highly robust $SiN_x$ films for screen-printed mc-Si solar cells. The Gas flow ratio, $R=[SiH_4]/[NH_3]$, in a mixture of silane and ammonia was varied in the range of 0.0910.235 while maintaining the total flow rate of the process gases to 4,200 sccm. The refractive index of the $SiN_x$ film deposited with a gas flow ratio of 0.091 was measured to be 2.03 and increased to 2.37 as the gas flow ratio increased to 0.235. The highest efficiency of the cell was $14.99\%$ when the flow rate of $SiH_4$ was 350 sccm (R=0.091). Generally, we observed that the efficiency of the mc-Si solar cell decreased with increasing R. From the analysis of the reflectance and the quantum efficiency of the cell, the decrease in the efficiency was shown to originate mainly from an increase in the surface reflectance for a high flow rate of $SiH_4$ during the deposition of $SiN_x$ films.

• 한국전산유체공학회:학술대회논문집
• /
• 1999.11a
• /
• pp.167-173
• /
• 1999

An Euler-based CFD tool has been developed for the performance evaluation of a thrust reverser mounted on a high bypass ratio turbofan engine. The computational domain surrounded by the ground and non-reflection boundary includes the whole nacelle configuration with a deployed thrust reverser. The numerical algorithm is based on the modified Godunovs scheme to allow the second order accuracy in both space and time. The grid system is generated by using eleven multi-blocks, of which the total cell number is 148,400. The thrust reverser is modeled as if it locates at the nacelle simply in all circumferential direction. The existence of a fan and an OGV(Outlet Guide Vane) is simulated by adopting the actuator disk concept, in which predetermined radial distributions of stagnation pressure ratio and adiabatic efficiency coefficient are used for the rotor type disk, and stagnation pressure losses and flow outlet angles for the stator type disk. All boundary conditions including the fan and OGV simulation are treated by Riemann solver. The developed solver is applied to a turbofan engine with a bypass ratio of about 5.7 and the diameter of the fan cowl of 83 inch. The computational results show that the Euler-based inviscid method is very useful and economical to evaluate the performance of thrust reversers.

• Journal of Korea Multimedia Society
• /
• v.20 no.1
• /
• pp.17-31
• /
• 2017

The aim of the paper is to present an object recognition method toward augmented reality system that utilizes existing education instruments that was designed without any consideration on image processing and recognition. The light reflection, sizes, shapes, and color range of the existing target education instruments are major hurdles to our object recognition. In addition, the real-time performance requirements on embedded devices and user experience constraints for children users are quite challenging issues to be solved for our image processing and object recognition approach. In order to meet these requirements we employed a method cascading light-weight weak classification methods that are complimentary each other to make a resultant complicated and highly accurate object classifier toward practically reasonable precision ratio. We implemented the proposed method and tested the performance by video with more than 11,700 frames of actual playing scenario. The experimental result showed 0.54% miss ratio and 1.35% false hit ratio.

• Journal of Multimedia Information System
• /
• v.8 no.2
• /
• pp.93-100
• /
• 2021

Under the time-varying temperature, the high-temperature radiation of forgings and the change of reflection characteristics of oxide skin on the surface of forgings lead to the difficulty of obtaining images to truly reflect the geometric characteristics of forgings. It is urgent to study the clear and reliable acquisition method of hot forging feature image under time-varying temperature to meet the requirements of visual measurement of hot geometric parameters of forgings. Based on this, this chapter first puts forward the quality evaluation method of forging feature image, which provides guarantee for the accurate evaluation of feature image quality. Furthermore, the factors that affect the image quality, such as the radiation characteristics of forgings and the photographic characteristics of cameras, are analyzed, and the imaging spectrum which can effectively suppress the radiation intensity of forgings is determined. Finally, aiming at the problem that the quality of image acquisition is difficult to guarantee due to the drastic change of radiation intensity of forgings under time-varying temperature, an image acquisition method based on minimum signal-to-noise ratio (SNR) based laser light intensity adaptation is proposed, which significantly improves the definition of feature light strips in forging images at high temperature, and finally realizes the clear acquisition of feature images of large-scale hot forging under time-varying temperature.