• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2311-2317
• /
• 2011

In this paper, we study the temperature change of a ${\mu}$-bolometer focal plane array with a capacitive transimpedance amplifier bias cancellation circuit. Thermal analysis is essential to understand the performance of a ${\mu}$-bolometer focal plane array, and to improve the temperature stability of a focal plane array characteristics. In this study, the thermal analyses of a ${\mu}$-bolometer and its two reference detectors are carried out as a function of time. The analyses are done with the $30{\mu}m$ pitch $320{\times}240$ focal plane array operating of 60 Hz frame rate and having a columnwise readout. From the results, the temperature increase of a ${\mu}$-bolometer in FPA by an incident IR is estimated as $0.689^{\circ}C$, while the temperature increase by a pulsed bias as $7.1^{\circ}C$, which is about 10 times larger than by IR. The temperature increase of a reference detector by a train of bias pulses may be increased much higher than that of an active ${\mu}$-bolometer. The suppression of temperature increase in a reference bolometer can be done by increasing the thermal conductivity of the reference bolometer, in which the selection of thermal conductivity also determines the range of CTIA output voltage.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.8
• /
• pp.1552-1557
• /
• 2007

In this work, temperature stable pulse width modulation controller using bandgap reference voltage is proposed. Two bandgap reference voltages are designed by using BiCMOS technology which are temperature dependent and independent voltage references. PWM controller is designed by using 3.3 volt supply voltage and the output frequency is 1MHz. From simulation results, the variation of output pulse width is less than form +0.86% to -0.38% in the temperature range $0^{\circ}C\;to\;70^{\circ}C$.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.4
• /
• pp.136-141
• /
• 1996

In this paper, a new CMOS on-chip current reference circit for memory, operational amplifiers, comparators, and data converters is proposed. The reference current is almost independent of temeprature and power-supply variations. In the proposed circuit, the current component with a positive temeprature coefficient cancels that with a negative temperature coefficient each other. While conventional curretn and voltage reference circuits require BiCMOS or bipolar process, the presented circuit can be integrated on a single chip with other digiral and analog circits using a standard CMOS process and an extra mask is not needed. The prototype is fabricated employing th esamsung 1.0um p-well double-poly double-metal CMOS process and the chip area is 300um${\times}$135 um. The proposed reference current circuit shows the temperature coefficient of 380 ppm/.deg. C with the temperature changes form 30$^{\circ}C$ to 80$^{\circ}C$, and the output variation of $\pm$ 1.4% with the supply voltage changes from 4.5 V to 5.5 V.

• Journal of Advanced Information Technology and Convergence
• /
• v.8 no.2
• /
• pp.59-67
• /
• 2018

The minimum power supply voltage of a typical bandgap current reference (BGCR) is limited by operating temperature and input common mode range (ICMR) of a feedback amplifier. A new BGCR using a bandgap voltage generator (BGVG) is proposed to minimize the effect of temperature, supply voltage, and process variation. The BGVG is designed with proportional to absolute temperature (PTAT) characteristic, and a feedback amplifier is designed with weak-inversion transistors for low voltage operation. It is verified with a $0.18-{\mu}m$ CMOS process with five corners for MOS transistors and three corners for BJTs. The proposed circuit is superior to other reported current references under temperature variation from $-40^{\circ}C$ to $120^{\circ}C$ and power supply variation from 1.2 V to 1.8 V. The total power consumption is $126{\mu}W$ under the conditions that the power supply voltage is 1.2 V, the output current is $10{\mu}A$, and the operating temperature is $20^{\circ}C$.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.1
• /
• pp.42-47
• /
• 2011

Measurement uncertainty analysis of fuel flow using turbine flowmeter was performed for the case of altitude engine test. SAE ARP4990 was used as the fuel flow calculation procedure, as well as the mathematical model for the measurement uncertainty assessment. The assessment was performed using Sensitivity Coefficient Method. 11 parameters involved in the calculation of the flow rate were considered. For the given equipment setup, the measurement uncertainty of fuel flow was assessed in the range of 1.19~1.86 % for high flow rate case, and 1.47~3.31 % for low flow rate case. Fluctuation in frequency signal from the flowmeter had the largest influence on the fuel flow measurement uncertainty for most cases. Fuel temperature measurement had the largest for the case of low temperature and low flow rate. Calibration of K-factor and the interpolation of the calibration data also had large influence, especially for the case of very low temperature. Reference temperature, at which the reference viscosity of the sample fuel was measured, had relatively small contribution, but it became larger when the operating fuel temperature was far from reference temperature. Measurement of reference density had small contribution on the flow rate uncertainty. Fuel pressure and atmospheric pressure measurement had virtually no contribution on the flow rate uncertainty.

• Fire Science and Engineering
• /
• v.27 no.4
• /
• pp.41-46
• /
• 2013

The present study has been conducted to investigate the reaction kinetics and pyrolysis parameters for flame propagation analysis of furniture material components. TGA measurement for component materials such as MDF (medium density fiberboad) panel including coating material, synthetic leather and foam cushion are performed under maximum temperature of $600^{\circ}C$ and heating rate of $10^{\circ}C/min$. The results of TGA have shown that the peak temperature of MDF panel was $324^{\circ}C$ and the initial peak temperature of coating material decreased by $270{\sim}280^{\circ}C$. In the case of synthetic leather and foam materials, the reference temperature and reference rate depend on the type of polymer consisting the sample, the initial kinetic characteristics was classified into 2 categories of about $270^{\circ}C$ and $420^{\circ}C$ of reference temperature for the tested synthetic materials. The present study showed the pyrolysis parameters of reference temperature and reference rate proposed by Lyon to evaluate the pre-exponential factor and activation energy. The present study can contribute to improve the reliability of computational fire analysis and enhance the understanding of fire propagation phenomena based on the thermal properties study of material.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.8
• /
• pp.64-70
• /
• 1997

This paper presents a parameter optimization method using evolutionary programming in voltage reference circuit because the designer must select appropriate parameter values of the circuit taking into consideration both powr voltage and temperature variation. In this paper, evolutionary programming is suggested as an approach for finding good parameters with which the reference voltage variation is small with respect to temperature variation. Simulation results. Simulation results show that this method is effective in circuit design.

• Proceedings of the KIEE Conference
• /
• 1998.11b
• /
• pp.403-406
• /
• 1998

There are two cases of error occurrence of STT(Smart Temperature Transmitter). One is that because of unstable reference voltage, data from A/D converter is not reliable. The other is that because of change of room temperature, this change affects conversion of A/D converter. In this paper, we show algorithms be adapted to STT for reliable conversion of A/D converter through a experiment and compensation for temperature change. In a experiment, we collect data from reference voltage and ground then calculate nominal value of these at constant temperature during A/D converter initialization or at any conversion time. Algorithm for compensation for unstable reference voltage calculates a correction factor and adapts it to compensation for malfunction of A/D converter. Algorithm for compensation for variation of room temperature is come from linearization of thermistor but is adapted to zener diode, not thermistor, therefor we have less effort for compensation for temperature and have a idea that it can be adapted to A/D converter system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1239-1243
• /
• 2004

A novel voltage-current reference circuit for stable voltage-current applications is Proposed. Circuits for a positive and for a negative voltage-current reference are presented and are designed with commercial CMOS technology. The voltage-current reference that is stable over ambient temperature variations is an important component of most data acquisition systems. These results are verified by the HSPICE simulation $0.8{\mu}m$ parameter. As the result, the temperature dependency of output voltage and output current each is $0.57mV/^{\circ}C$, $0.11{\mu}A/^{\circ}C$ and the power dissipation is 1.8 mV on 5V supply voltage.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.89-92
• /
• 2001

In this paper, a simple low-power CMOS current reference circuit is proposed. The reference circuit includes parasitic pnp BJTs and resistors. Temperature compensation is made by adding a current component proportional to a thermal voltage to a current component proportional to a base-to-emitter voltage. The designed circuit has been simulated using a 0.25${\mu}{\textrm}{m}$ n-well CMOS process parameters. The simulation results show that the reference current is 34.96$mutextrm{A}$$\pm$0.04$mutextrm{A}$ in the temperature range of -2$0^{\circ}C$ to 12$0^{\circ}C$ The reference current varies less than 0.6% when the power supply voltage changes from 2.5V to 3.5V For $V_{DD=5V}$ and T=3$0^{\circ}C$ the power consumption is 520㎼ during normal operation but reduces to 0.l㎻ during power-down mode.