• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.1
• /
• pp.1-8
• /
• 1987

In this paper, resonance frequencies of a reentrant cavity are computed by the mode matching method and the mode orthogonality. The reentrant cavity is composed of a coaxial cable and a cylindrical waveguide, so that resonance frequencies of the resonator can be varied by adjusting the length of the inner conductor of a coaxial cable. The result can be applied to numerous microwave devices such as klystron, wavemeter and resonant circuits of a amplifier and to the measurement of dielectric parameters.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.5
• /
• pp.407-411
• /
• 2005

A simulation investigation on the circular cylindrical reentrant cavity with axial ridges and a cylindrical circumferential slot is presented. This study indicates that by properly adjusting the dimensions of the ridge sand the slot, the size of the cavity can be miniaturized to around $\lambda_0$ The simulation results using CST MWS show good agreement with past theoretical predictions and provide useful insight into fundamental concerns associated with electrically small antennas.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.3
• /
• pp.18-27
• /
• 2002

Flame behavior in inner and outer the cavity and flame temperature have an important influence on the formation and oxidation of NOx and soot. Therefore, in this study, the combustion chamber of toroidal and reentrant that have different flow characteristics of inside and outside the cavity and load, and so forth are determined as parameters of experimental conditions. An attempt has been made to obtain the effect of flame temperature and KL value in idler and outer cavity on the formation and oxidation of soot using the two-color method.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.6
• /
• pp.760-767
• /
• 2009

This thesis focuses on the study of high-power, coupled-cavity traveling-wave tube(CCTWT) for radar applications. The CCTWT employed a reentrant double-slot staggered RF cavity structure. Computational analysis of the X-band, double-slot staggered structures is carried out through the use of HFSS code, which solves Maxwell's equations fully in three-dimensions. The non-linear, large-signal performance of CCTWTs are predicted from numerical simulations using a three-dimensional particle-in-cell code, MAGIC3D. With beam voltage set to 12.7~13kV and beam current at 300mA, the CCTWT produces a saturated radiation power of 350~430W, corresponding to an electronic efficiency of 8.9~11.2% and a gain of 23.7~24.2dB within a frequency range of 7.9~8.4GHz.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.12
• /
• pp.971-976
• /
• 2006

The objectives of this paper are to study the characteristics of pool boiling heat transfer for enhanced tubes used in the evaporator of turbo chiller and to provide a guideline for optimum design of an evaporator using HFC134a. Three different enhanced tubes are tested at 4 different saturation temperatures. The wall super heated temperature difference ranges from $0.5^{\circ}C\;to\;3.5^{\circ}C$. The refrigerant, HFC134a evaporates on the outside of the tube while the chilled water flows inside the tube. This study provides experimental heat transfer coefficients for evaporation on the enhanced tubes. It is found that the turbo-II tube provides the highest heat transfer coefficient.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.2
• /
• pp.132-140
• /
• 2010

The very erosive cavitation is simulated by an inclined propeller dynamometer in the medium-size cavitation tunnel of MOERI. The inclined shaft for propeller makes strong cavitaion, which occurs around the root of a propeller blade. The cavitation begins at the leading edge of the propeller and contracted toward the trailing edge through the reentrant jet action. The cavity focused on the region near the trailing edge collapsed over the blade surface. As the impact pressure by the cavitation collapsing is too strong, it can damage the blade surface in the form of pit. This cavitation impacts created by the collapsing process are similar to the full-scale ones and are different from those by other erosion test methods. The newly developed cavitation erosion test method can be applied to evaluate the materials such as metals, ceramics and coatings in terms of cavitation resistance.