• Journal of Advanced Marine Engineering and Technology
• /
• v.8 no.2
• /
• pp.74-80
• /
• 1984

In the reduction gears for marine propulsion engine such as turbine or high speed diesel engine, the standard involute double helical gears are generally used. However the addendum modification gear can be used in the reduction gear as it has flexibility for gear design on the tooth strength, scoring and operating noise. In this case, the determination of gear shaft bearing load is difficult by the alternation of operating pressure angle. In this paper, the formulas of bearing load according to the arrangements of the reduction gears are derived and the diagrams of operating pressure angle according to the modification coefficient are presented.

• Communications of the Korean Mathematical Society
• /
• v.37 no.2
• /
• pp.473-496
• /
• 2022

In 2014, Liu and Wang established a large number of interesting reduction, transformation and summation formulas for the Kampé de Fériet function. Inspired by the work, we aim to find further several transformation and reduction formulas for the Kampé de Fériet function. Theses formulas are mainly based on the formulas given by Liu and Wang [33].

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.998-1001
• /
• 2010

Most firming agent used in Korea is cement-firming agent. Cement-firming agent absorb water for combination, and then it makes ettringite. Through this chemical process, soft ground is firmed by cement-firming agent. Although most cement-firming agent used in Korea made from CSA, it relies on imports. Therefore, the development of soft ground firming agent using new materials is required. In this study, we suggested that EAF reduction slag not used for anything in the steel industry is available for material of soft ground firming agent. If EAF reduction slag is used in soft ground firming agent, it will be possible to solve the problem with treatment of slag and improvement of soft ground.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.3
• /
• pp.8-14
• /
• 2007

The geometry in the weight reduction design is very required to be started from the conceptual design with low cost, high performance and quality. In this point, a topological shape fur optimization concerned with conceptual design of structure is important. The method used in this paper combines three optimization techniques, where the shape and physical dimensions of the structure and material distribution are hierachically optimized, with the maximum rigidity of structure and lightweight. As the applications, the technology of weight reduction design is applied on designs of aluminum control arm and inner panel of hood.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.638-641
• /
• 1995

The model-technology has been conduced to a large quantity of automobile and electric products. However, many problems in mold-technology have been solved through trial and error of experts. So it has given rise to overdesign of mold and generated other problems in production line. In this paper we choosed the lower-mold of a cool chamber in refrigerator as the model of the study and mass reduced overdesigned mold. In mass reduction process, several cases in plane processing error were selected for the sample case through FEM analysis & simplicated theory analysis and each case was evaluated for mass reduction.

• Advances in environmental research
• /
• v.4 no.4
• /
• pp.263-271
• /
• 2015

In this study, the effect of initial nitrate loading on nitrate removal and byproduct selectivity was evaluated in a continuous system. Nitrate removal decreased from 100% to 25% with the increase in nitrate loading from 10 to $300mg/L\;NO_3-N$. Ammonium selectivity decreased and nitrite selectivity increased, while nitrogen selectivity showed a peak shape in the same range of nitrate loading. The nitrate removal was enhanced at low catalyst to nitrate ratios and 100% nitrate removal was achieved at catalyst to nitrate ratio of ${\geq}33mg\;catalyst/mg\;NO_3-N$. Maximum nitrogen selectivity (47%) was observed at $66mg\;catalyst/mg\;NO_3-N$, showing that continuous Cu-Pd-NZVI system has a maximum removal capacity of 37 mg $NO_3{^-}-N/g_{catalyst}/h$. The results from this study emphasize that nitrate reduction in a bimetallic catalytic system could be sensitive to changes in optimized regimes.

• Journal of Powder Materials
• /
• v.16 no.3
• /
• pp.191-195
• /
• 2009

The calcination and hydrogen-reduction behavior of Fe- and Ni-nitrate have been investigated. $Fe_2O_3$/NiO composite powders were prepared by chemical solution mixing of Fe- and Ni-nitrate and calcination at $350^{\circ}C$ for 2 h. The calcined powders were hydrogen-reduced at $350^{\circ}C$ for 30 min. The calcination and hydrogen-reduction behavior of Fe- and Ni-nitrate were analyzed by TG in air and hydrogen atmosphere, respectively. TG and XRD analysis for hydrogen-reduced powders revealed that the $Fe_2O_3$/NiO phase transformed to $FeNi_3$ phase at the temperature of $350^{\circ}$. The activation energy for the hydrogen reduction, evaluated by Kissinger method, was measured as 83.0 kJ/mol.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.5
• /
• pp.274-279
• /
• 2015

Reduced graphite oxides (rGOs) were prepared by the common graphite oxidation method and the subsequent reductions. The reduction of graphite oxides (GOs) was conducted chemically and/or thermally. To further reduce the as-prepared rGOs, GOs were treated with chemical/thermal reductions or thermal/chemical reductions, in which the reduction sequence was also considered. The structural changes of as-prepared rGOs, depending on reduction methods, were investigated by X-ray diffraction analyses, Raman spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy. In addition, we discuss the structural change of the rGOs and their closely related physical and electrical properties, such as thermogravimetry, nitrogen adsorption isotherm, and sheet resistance.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.2
• /
• pp.166-171
• /
• 2016

Size reduction is one of the major pre-processing operations in using biomass as a source of energy or raw materials for forest products industry. The grinding characteristics of dried yellow poplar wood chips were investigated using laboratory knife mill with three different screen aperture diameters to provide the basic information for the optimizing of size reduction processes in biomass industry. Average specific energy consumptions were 0.157, 0.137, and 0.093 Wh/g for the screen aperture diameters of 5.0, 7.5, and 9.0 mm, respectively. According to the results of size distribution analysis of ground particles, the sizes of the most of ground particles were much smaller than the aperture diameters of the screens installed on knife mill used in this study.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.35-38
• /
• 2004

In general, tube drawing process is composed of two steps, so called first drawing and second drawing. Drawing cracks are mainly occurred during the 2nd drawing process due to the improper drawing process. In order to analyze the reduction distribution in successive two-step drawing process, tube drawing process was simulated by finite element method. From the finite element analysis, the balance between first and second reduction is proved to be important factor to prevent drawing cracks. Hence the numerical expression was developed for tube drawing process to distribute even strain and criteria curves that can predict the safe drawing region were also proposed using this numerical formula.