• Journal of the Korean Geosynthetics Society
• /
• v.5 no.1
• /
• pp.1-7
• /
• 2006

Despite a number of advantages of reinforced earth walls over conventional concrete retaining walls, there exit concerns over long-term residual deformation when used as part of permanent structures. In view of these concerns, time-dependant deformation characteristics of geosynthetic reinforced modular block walls under sustained loads were investigated using reduced-scale model tests. The results indicated that a sustained load can yield appreciable magnitude of residual deformation, and that the magnitude of residual deformation depends on the loading characteristic as well as reinforcement stiffness.

• Fire Science and Engineering
• /
• v.25 no.5
• /
• pp.128-133
• /
• 2011

The present study performs a series of 40 % reduced scale of ISO-9705 fire test to investigate the characteristics of heat flux on the floor level in terms of fire characteristics and location in the compartment. The heat flux was measured with Schmidt-Boelter type heat flux gauge at two locations on the floor level of inside and doorway side of the compartment. Different types of fuel - methane, heptane, toluene, ethanol, polystyrene - were burned in this test series. The measured heat flux inside of the compartment was relatively higher than that of front side as the heat release rate of fire and upper layer temperature increased. The difference of measured heat flux at inside and doorway side increased for high sooty fire. The present study shows that the heat flux distribution at lower layer greatly depend on the thermal radiation from fire and upper layer, not only the upper layer temperature but also various fire characteristics such as composition of combustion gases, soot concentration, ventilation condition and so on.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.2
• /
• pp.225-229
• /
• 2012

This paper proposes a reduced-scale simulator that can replace numerical analytic methods for the estimation of potential distribution caused by ground faults in various grounding systems. The simulator consists of a hemispherical electrolytic tank, a three-dimensional potential probe, a grounding electrode, and a data acquisition module. The potential distribution is measured using a potentiometer with a position-tracing function when a test current flows to the grounding electrode. Using the simulator, we could clearly analyze the potential distribution for a reduced- scale model by one-eightieth of the buried depth and length of the grounding rod and grounding grid. Once both the shape of the grounding electrode and the fault current are known, the actual potential distribution can be estimated.

• Research in Community and Public Health Nursing
• /
• v.19 no.2
• /
• pp.247-259
• /
• 2008

Purpose: This study was conducted to develop a teacher-efficacy scale which is adequate for heath education teachers. Method: A preliminary questionnaire was made based on the hypothetical factors. A total of 364 health education teachers answered to the preliminary test, and the potential factors of teacher-efficacy were checked out by exploratory factor analysis (EFA). In the main test 378 health education teachers answered, the factor structure was drawn by EFA, and confirmatory factor analysis (CFA) was conducted to test and the fitness of the factor model. Results: Through the preliminary test, 5 potential factors were found, which were instruction, health-service, administrative task, interpersonal relationship, and community connection. Also, 48 items were reduced to 31 items. Through the main test, from the 34 items were extracted 4 factors with 24 items, And then teacher-efficacy scale was developed, which included the subscales of instruction efficacy, health-service efficacy, task-interpersonal efficacy, and community connection efficacy. Conclusion: Different from that for other subject teachers, the factor structure for health teachers had 4 factors with 24 items. The scale developed in this study is consistent with health teachers' work areas, and for this reason, has significance as a adequate and valid scale to measure teacher-efficacy of health education teachers.

• Geomechanics and Engineering
• /
• v.31 no.4
• /
• pp.423-437
• /
• 2022

The objective of the study is to evaluate the feasibility of the dynamic behavior of slope through both 1 g shaking table test and numerical analysis. Accelerometers were installed in the slope model with different types of seismic waves. The numerical analysis (ABAQUS and DEEPSOIL) was used to simulate 1 g shaking table test at infinite boundary. Similar Acceleration-time history, Spectral acceleration (SA) and Spectral acceleration amplification factor (Fa) were obtained, which verified the feasibility of modeling using ABAQUS and DEEPSOIL under the same size. The influence of the size (1, 2, 5, 10 and 20 times larger than that used in the 1 g shaking table test) of the model used in the numerical analysis were extensively investigated. According to the similitude law, ABAQUS was used to analyze the dynamic behavior of large-scale slope model. The 5% Damping Spectral acceleration (SA) and Spectral acceleration amplification factor (Fa) at the same proportional positions were compared. Based on the comparison of numerical analyses and 1 g shaking table tests, it was found that the 1 g shaking table test result can be utilized to predict the dynamic behavior of the real scale slope through numerical analysis.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1997.10a
• /
• pp.175-182
• /
• 1997

The characteristic tests of reduced-scale high damping and lead rubber bearings are performed by changing the shear displacements and the vertical loads. The test frequency is 0.5Hz. Test results show that the shear stiffnesses obtained for both bearings are less than target values, but the damping values are greater than the targets. The shear stiffness and damping of lead are larger than those of high damping bearings. The shear-deformation characteristic values such as stiffness, damping and yield load values are changed according to the level of design vertical loads.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.53 no.4
• /
• pp.59-65
• /
• 2011

The purpose of this study was to analyze the water quality change when wastewater applied to study paddy fields. CREAMS-PADDY (Chemical, Runoff and Erosion from Agricultural Management System) model was used to estimate the field-scale water quality. Simulated results were compared with observed data monitored from Byeongjeom study paddy fields which is located near the Suwon sewage treatment plant in Gyeonggi-do. Significance analysis was performed for the three different irrigation water quality level and five fertilizer reduction scenarios using LSD (Least Significant Difference) and DMRT (Duncan's Multiple Range Test). Total nitrogen was found to be significant for both irrigation water quality level and fertilizer reduction while total phosphorus was not. Annual drainage load for total nitrogen was reduced by 66~92 % compared to irrigation load when treated wastewater irrigated to study paddy fields from 2002 to 2007. Total phosphorus was reduced by 70~86 %.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.2 no.2
• /
• pp.32-40
• /
• 2000

This paper presents the results of a parametric study on the behavior of tunnel face reinforced with horizontal pipes. A series of reduced-scale model tests was carried out to in an attempt to verify previously performed three-dimensional numerical modeling and to investigate effects of reinforcement layout on the tunnel face deformation behavior. The results of model tests indicate that the tunnel face deformation can significantly reduced by pre-reinforcing the tunnel face with longitudinal members and thus enhancing the tunnel stability. In addition, the model tests results compare fairly well with those from the previously performed three-dimensional finite element analysis. Therefore, a properly calibrated three dimensional model may effectively be used in the study of tunnel face reinforcing technique.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.5
• /
• pp.896-904
• /
• 1987

In this paper, a design method for sequential circuit which is easy to have Built-in Self Test is kproposed using the functional advantages of multifunctional BILBO and LSSD. To achieve the hardware reduction, it is designed that a multifunctional BILBO has double operational functions of NLFSR and LFSR, when neccessary, and that test signal could be used as an input-output signal in the same line. By applying the proposed multifunctional BILBO to the sequential PLA, the test patterns and the additional circuit could be reduced in test operation and the propagation delay is vanished in normal operation, as we expected. Above them, the partitioned method for large scale sequential circuit is also suggested and it is observed that test patterns and additional circuit in them reduced by this method.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2046-2048
• /
• 2005

This paper deals with ground potential rise of structure grounding electrode when a test current flows through grounding electrode. In order to analyze the potential gradient of ground surface on structure grounding electrode, the reduced scale model has been used. The structures were designed through reducing real buildings and fabricated with four types on a scale of one-one hundred sixty. The supporter was made to put up with weight of structure and could move into vertical, horizontal, rotary direction. When a test current flowed through structure grounding electrodes, ground potential rise was the lowest value at electric cage type(type B). According to resistivity and absorption percentage in concrete attached to structure, the potential distribution of ground surface appeared differently.