• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.245-248
• /
• 1998

This paper proposes a sensorless velocity estimator using the reduced-order state equation of induction motor based on Kalman Filter. The electrical transients in the stator voltage equations of induction motor are neglected in the reduced-order model. The advantage of using the reduced-order model is to reduce the required number of numerical integrations for filtering the rotor speed. As changing the operating points and the parameters of the induction motor in simulation studies, the behavior of the sensorless velocity estimator as predicted by the reduced-order state equation of induction machine is compared with the behavior predicted by the complete state equation of induction machine.

• 한국의류산업학회지
• /
• 제18권5호
• /
• pp.716-723
• /
• 2016

The purpose of this study was to investigate the change in blood velocity(mm/sec) when compression and/or heat were applied to the knee joint for the elderly who has both normal and painful legs with osteoarthritis(OA). Experimental compression knee band was prepared from the 3D knee data of the average women in 60's. 3D replica of knee was reduced by 7, 10, and 13% from the nude pattern in course direction. Clothing pressure was measured at the front and back of each healthy and painful knee of elderly women for one minute while standing and sitting on the chair. Blood velocity was measured at 13 cm upper from the mid-patella for 15 minutes. Results are as follows: first, compression or heating treatment itself did not change blood velocity of both legs; second, combination treatment with heating and compression was effective to increase blood velocity. In details, for healthy legs, combination treatments with compression by 10% reduced pattern(about 1.3kPa) and heating($43^{\circ}C$) induced the maximal blood velocity, however, for knees with OA, 7% reduced pattern(about 1.0kPa) with simultaneous heating($43^{\circ}C$) was more effective than other cases. These results indicated that pain and spasticity of knee joint with OA could be reduced by applying heat and compression therapy, where the compression level of painful knee should be slightly lower than of healthy leg.

• 제어로봇시스템학회논문지
• /
• 제14권6호
• /
• pp.603-607
• /
• 2008

This paper proposes a fast acquisition method using INS velocity and multiple correlators for high speed vehicles. In order to reduce acquisition time in GPS receiver, the method utilizes inertial velocity information and multiple correlators. Search range of the Doppler frequency is reduced by using INS velocity and the number of cells at one search can be increased by using multiple correlators. By using both multiple correlators and the INS velocity in the acquisition, search space can be greatly reduced. Experimental results show that the method gives faster signal acquisition performance than the conventional method.

• 한국화재소방학회논문지
• /
• 제21권3호
• /
• pp.61-68
• /
• 2007

본 연구에서는 지하생활공간을 대상으로 풍속의 변화에 대한 축소모델 실험을 통하여 열유동 및 화재성상을 분석하였다. 풍속이 증가할수록 화재실의 온도상승 시간은 빨라지고, 실의 온도도 증가하였다. 그리고 풍속이 증가할수록 화재실의 개구부에서 최고온도를 나타내었다. 화재확산에 따른 열유동은 풍속이 증가할수록 와류확산을 촉진시켜 연기발생과 화염의 크기를 증가시키고, 인근실의 내부보다 통로에서 높은 온도분포를 나타내었다. 끝으로 지하생활공간의 화재시 열유동은 풍향과 풍속에 의해 화재확산이 결정되어지고 풍속이 증가할수록 온도증가와 감소는 빠르게 진행됨을 확인할 수 있었다.

• Advances in Energy Research
• /
• 제4권3호
• /
• pp.213-221
• /
• 2016

The main purpose of this work is to test the validation of use of a four step reaction mechanism to simulate the laminar speed of hydrogen enriched methane flame. The laminar velocities of hydrogen-methane-air mixtures are very important in designing and predicting the progress of combustion and performance of combustion systems where hydrogen is used as fuel. In this work, laminar flame velocities of different composition of hydrogen-methane-air mixtures (from 0% to 40% hydrogen) have been calculated for variable equivalence ratios (from 0.5 to 1.5) using the flame propagation module (FSC) of the chemical kinetics software Chemkin 4.02. Our results were tested against an extended database of laminar flame speed measurements from the literature and good agreements were obtained especially for fuel lean and stoichiometric mixtures for the whole range of hydrogen blends. However, in the case of fuel rich mixtures, a slight overprediction (about 10%) is observed. Note that this overprediction decreases significantly with increasing hydrogen content. This research demonstrates that reduced chemical kinetics mechanisms can well reproduce the laminar burning velocity of methane-hydrogen-air mixtures at lean and stoichiometric mixture flame for hydrogen content in the fuel up to 40%. The use of such reduced mechanisms in complex combustion device can reduce the available computational resources and cost because the number of species is reduced.

• 한국항공우주학회지
• /
• 제37권10호
• /
• pp.992-997
• /
• 2009

본 논문에서는 제한된 센서 조건에서 유도탄 동체의 각속도를 계산하는 법을 보이고 Flight Motion Simulator(FMS)를 이용한 각속도 계산식 검증을 다룬다. 일반적으로 유도탄 동체의 각속도는 동체에 탑재하는 각속도 자이로를 이용하여 측정하지만, 유도탄 동체에 탑재하는 관성 센서 중에 피치와 요 각속도 자이로가 없는 제한된 센서 조건을 가정한다. 이와 같은 제한된 센서 조건에서 김블 탐색기 자이로, 동체의 롤 각속도 자이로, 김블의 자세 측정값 및 자세 변화율을 이용하여 유도탄 동체의 각속도를 계산할 수 있음을 보인다. 제안한 각속도 계산식을 검증하기 위하여 FMS를 이용한 실험을 수행하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.661-667
• /
• 2001

This paper is concerned with the effects of periodically approaching upstream wakes on cascade-flow and loss. The reduced frequency of the periodic wakes was varied in the narrow range from 0.5 to 0.7. According to a wake-passing through the cascade, two velocity deficits appear near the boundary layer contour in the downstream from about 60% chord-length. The first velocity deficit is caused by a periodic wake and the second one appears after some delayed time. The second velocity deficit may be interpreted as the results of reattachment of flow-separation. The higher reduced frequency decreases the duration time of separation appearance and the lesser loss of aerofoil is resulted.

• 한국정밀공학회지
• /
• 제30권12호
• /
• pp.1295-1301
• /
• 2013

The cause of flow mark defect is known as non-uniform temperature of mold surface when the flow front meets the cold cavity. The exact definition and classification of Flow mark is not clear because the mechanism of flow mark is not figured out till now. Any injection molding analysis software can not predict the flow mark phenomena. To solve weldline and flow mark defects, the gate thickness is reduced to increase the melt front velocity and the melt front velocity of the flow mark area is increased from 82.3mm/s to 104.7mm/s. In addition, the bulk temperature of the flow mark area is increased from $178.3^{\circ}C$to $215.2^{\circ}C$ by adding a cold slug well. The flow mark phenomena can be greatly reduced by increasing the flow front velocity and elevating the bulk temperature.

• 대한기계학회논문집B
• /
• 제26권2호
• /
• pp.219-226
• /
• 2002

This paper is concerned with the effects of periodically approaching upstream wakes on cascade-flow and loss. The reduced frequency of the periodic wakes was varied in the narrow range from 0.5 to 0.7 Corresponding to a wake-passing through the cascade, two velocity deficits appeared near the boundary layer contour in the downstream from about 60% chord-length. The first velocity deficit was caused by a periodic wake and the second one appeared after some delayed time. The second velocity deficit was interpreted as the results of reattachment of flow-separation. The higher reduced frequency decreased the duration time of separation appearance and the lesser losses of blade were resulted.

• Journal of applied mathematics & informatics
• /
• 제41권2호
• /
• pp.401-411
• /
• 2023

The effects of longitudinal velocity dusty fluid flow in a weak magnetic field are investigated in this paper. An external uniform magnetic field parallel to the flow of dusty fluid influences the flow of dusty fluid. Besides that, the problem under investigation is completely defined in terms of identifying parameters such as longitudinal velocity (u), Hartmann number (M), dust particle interactions β, stock resistance γ, Reynolds number (Re) and magnetic Reynolds number (Rm). While using suitable transformations of resemblance, The governing partial differential equations are transformed into a system of ordinary differential equations. The Hankel Transformation is used to solve these equations numerically. The effects of representing parameters on the fluid phase and particle phase velocity flow are investigated in this analysis. The magnitude of the fluid particle is reduced significantly. The result indicates the magnitude of the particle reduced significantly. Although some of our numerical solutions agree with some of the available results in the literature review, other results differs because of the effect of the introduced magnetic field.