• 대한기계학회논문집A
• /
• 제22권4호
• /
• pp.762-767
• /
• 1998

The main torsional vibration source of the powertrain is the fluctuation of engine torque. The gear rattle is impact generating in the backlash of the free gear due to this torsional vibration. Optimization of the clutch torsional characteristic is one of the effective method to reduce the idle gear rattle. Many researches have been reported on this problem but only few of them give sufficient consideration to the detailed clutch modeling and the experiment. This paper pays attention to the optimization of clutch design parameters and the experiment to reduce the idle gear rattle vibration and noise.

• 소음진동
• /
• 제8권4호
• /
• pp.670-682
• /
• 1998

Ball type automatic balancer is used to reduce the vibration caused by unbalance of rotor. In this study, A analytic modeling of a front loaded washing machine with ball type automatic balancer has been suggested theoretically and ADAMS has been used to analyze the dynamic characteristics of automatic balancer. It is found from simulation and experimental results that the automatic balancer suppress the steady state vibration of washing machine effectively. The test results match with the simulation results of ADAMS, thereby the dynamic model of ADAMS can be used as virtual prototype to predict the vibration characteristics which could be changed by the modification of design variableand can reduce the design cycle sharphy. To maximize the balancing effect of automatic balancer, the friction between balls and race and the deviation between geometric center and rotation center of drum need to be minimized and the optimum design for the stiffness of flange shaft and the angular acceleration of drum should be achieved.

• 한국소음진동공학회논문집
• /
• 제20권5호
• /
• pp.470-476
• /
• 2010

In this work, the mechanism of structure-borne noise resulting from vibration of a compressor for a refrigerator is experimentally analyzed and an effective method is proposed to reduce the noise. Firstly, the emission noise, when the compressor is turned on and off, is measured and analyzed to identify the generation mechanism of structure-borne noise. And the acceleration on the outer wall of the refrigerator is also analyzed to identify the distribution of vibration. Secondly, an effective design method to reduce the noise is suggested by using the finite element analysis and Taguchi method. Consequently an optimal design of the refrigerator, which has lower noise, is obtained and then its performance and validity are verified through the analysis and test.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.282-283
• /
• 2008

According to the development of vehicle technique, the improved NVH performance is required in the vehicle which have the high effectiveness and the high output of the powertrain. This vehicle has to be adapted to active engine mounting system to reduce the vibration in accordance with various vehicle information. The pneumatic active engine mounting system is consist with engine mount, solenoid valve, air tank and control unit totally. The important technique of this system is to reduce the vibration by the air pressure. This paper contains the development process of the pneumatic active engine mounting system and confirm the performance of this system test and vehicle test.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.489-496
• /
• 2008

This paper investigates active noise control of ducts using Filtered-x Least Mean Square (FXLMS) algorithms to reduce noise transmission. Single channel FXLMS (MFXLSM) and multiple channel FXLMS (MFXLMS) algorithms are used to implement the active control systems. The transmission loss is significantly increased by SFXLMS but the sound pressure level (SPL) at the upstream of the error sensor is increased while that of downstream is very low. This increase of the upstream SPL causes the duct wall to vibrate and so to radiate noise. To prevent the wall vibration generated by the sound field upstream, global sound field control is required. To reduce SPL globally along the duct, active noise control using MFXLMS is implemented. We can then obtained globally reduced SPL. It is found experimentally that the vibration level, and so the radiated noise level. can be reduced by the active noise control using MFXLMS.

• 한국소음진동공학회논문집
• /
• 제19권1호
• /
• pp.24-34
• /
• 2009

This paper investigates active noise control of ducts using filtered-x least mean square(FXLMS) algorithms to reduce noise transmission. Single channel FXLMS(SFXLSM) and multiple channel FXLMS(MFXLMS) algorithms are used to implement the active control systems. The transmission loss is significantly increased by SFXLMS but the sound pressure level(SPL) at the upstream of the error sensor is increased while that of downstream is very low. This increase of the upstream SPL causes the duct wall to vibrate and so to radiate noise. To prevent the wall vibration generated by the sound field upstream, global sound field control is required. To reduce SPL globally along the duct, active noise control using MFXLMS is implemented. We can then be obtained globally reduced SPL. It is found experimentally that the vibration level, and so the radiated noise level, can be reduced by the active noise control using MFXLMS.

• 한국소음진동공학회논문집
• /
• 제14권1호
• /
• pp.40-49
• /
• 2004

In this paper, vibration response of aerial gas pipeline due to vehicle loads was quantitatively estimated through experiment and analysis in open cut construction site. The vehicle vibration of various construction machines causes serious effect to the aerial gas pipeline. The new vibration prediction equations presented in this study can estimate the vibration velocity response of the aerial gas pipeline. In the nitration prediction equations, the vehicle′s weight and traveling velocity, which are the sources of vibration, are combined into the term called, "scaled weight" Methods to reduce vibration were proposed in case the vibration velocity response of the gas pipeline exceeded the vibration criterion, using the vibration prediction equations presented in this study. One was to limit the vehicle′s traveling velocity and the other to install the isolation equipment. Both methods can be estimated quantitatively.

• 소음진동
• /
• 제7권6호
• /
• pp.1031-1037
• /
• 1997

The main torsional vibration source of the driveline is the fluctuation of the engine torque. The gear rattle is generated by an impact in the backlash due to this torsional vibration. Optimization of the clutch torsional characteristic is one of the effective methods to reduce the idle gear rattle. Many researches have been reported on this problem but only few of them give sufficient consideration to the detail clutch modeling and clutch design parameters (stiffness, hysteresis torque, preload, first stage length). This paper pays attention to the gear impact mechanism and clutch design parameters to reduce the idle gear rattle with computer simulation.

• 한국정밀공학회지
• /
• 제22권11호
• /
• pp.104-110
• /
• 2005

GIS(Gas Insulated Switchgear) is used in electric power system, to insure non conductivity, breaking capacity and operating reliability. The commercial dynamic analysis code COSMOS MOTION and 3-D modeling program SOLID WORKS were used to simulate dynamic analysis of the closing resistors of the GIS in this paper. To reduce chatter vibration of closing resistors, the motion of moving and fixed parts of closing resistors were simulated by varying the spring constant, the damping coefficient and the mass of moving and fixed parts. The simulated results were compared with experimental results. As a result, chatter vibration of closing resistors of the GIS could be reduced by using the results. These data can be used to determine the spring constant, the damping coefficient and mass of a moving part to reduce chatter vibration when the next model is developed.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1987년도 한국자동제어학술회의논문집; 한국과학기술대학, 충남; 16-17 Oct. 1987
• /
• pp.479-483
• /
• 1987

The reducers are widely used to reduce output speed and to amplify driving torque of actuator for industrial robots and many industrial units. But the vibration of robot, which is affected by the reducer, becomes a problem for robot which has to move a driven part with high accuracy. This paper compares experimentally the vibration characteristics of the reducer for industrial robot.