• Journal of IKEEE
• /
• v.18 no.1
• /
• pp.25-30
• /
• 2014

In this paper, SCR(Silicon Controlled Rectifier)-based ESD(Electrostatic Discharge) protection circuit for power clamp is proposed. In order to improve latch-up immunity caused by low holding voltage of the conventional SCR, it is modified by inserting n+ floating region and n-well, and extending p+ cathode region in the p-well. The resulting ESD capability of our proposed ESD protection circuit reveals a high latch-up immunity due to the high holding voltage. It is verified that electrical characteristics of proposed ESD protection circuit by Synopsys TCAD simulation tool. According to the simulation results, the holding voltage is increased from 4.61 V to 8.75 V while trigger voltage is increased form 27.3 V to 32.71 V, respectively. Compared with the conventional SCR, the proposed ESD protection circuit has the high holding voltage with the same triggering voltage characteristic.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.2
• /
• pp.131-137
• /
• 2013

In this paper, the phase-shift full-bridge DC/DC converter with fixed-phase operation inverter is proposed. The proposed circuit consists of two full-bridge inverters which are connected in parallel. While one full-bridge inverter operates as the fixed-phase, it regulates the output voltage by adjusting the phase of the other inverter. During the normal operation period, the proposed circuit makes the less amount of conduction loss of the primary switches and secondary synchronous rectifiers, as well as the less amount of the current ripple of the output inductor, than the conventional phase-shift full-bridge DC/DC converter does. Also, it achieves high efficiency by reducing the snubber loss of the secondary synchronous rectifier. To sum up, the present inquiry analyzes the theoretical characteristics of the proposed circuit, and shows the experimental results from a prototype for 450W power supply.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.6
• /
• pp.759-769
• /
• 2015

Diode rectifiers are very popular in industry. However, they include large low-order harmonics in the input current and do not satisfy harmonic current content restrictions. To reduce the harmonics to the power system, several methods have been introduced. It is heavy and expensive solution to use passive filters as the solution for high power application. Another solution for the harmonic filter is utilization of active filter, but it is too expensive solution. Diode rectifiers with configurations using switching device have been introduced, but they are very complicated. The combined 12-pulse diode rectifier with the square auxiliary voltage supply has been introduced. It has the advantages that auxiliary circuit is simple and inexpensive compared to other strategies. The advanced auxiliary voltage supply in this thesis is presented as a new solution. When the square auxiliary voltage supply applied, the improvement of THD is 6~60[%] in whole load range. But when the advanced auxiliary voltage supply applied, it shows stable and excellent reduction effect of THD as 57~71[%]. Especially, for the case with 10[%] load factor, reduction effect of THD has little effect as 6[%] in the case of inserting a square auxiliary voltage supply. But when the proposed new solution applied, reduction effect has excellent effect as 71[%]. Theoretical analysis of the combined 12-pulse diode rectifier with the advanced auxiliary voltage supply is presented and control methods of the auxiliary supply is proposed. The reduction in the input current harmonics is verified by simulation using software PSIM.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.4
• /
• pp.59-65
• /
• 1997

This paper proposes a new approach for the design of a multi-output electronic ballast for fluorescent lamps of different outputs and control method. At first, a standard-output electronic ballast is constructed and then fluorescent lamps with different outputs are lighted by the frequency control of inverter circuit using MeV. This multi-output electronic ballast consists of a rectifier circuit, an inverter circuit, and a frequency control circuit to determine the optimal frequency for the lamps of different output. In order to verify the proposed design method, a prototype of a multi-output electronic ballast for 11 [WJ. 15[WJ compact fluorescent lamps and 20W fluorescent lamp is constructed. Results of observing the voltage and current characteristics of lamps are in accord with those of PSpice simulation. Also its efficacy is nearly the same as the other electronic ballasts. From the result, therefore, validity of the proposed design method of a multi-output electronic ballast for fluorescent lamps is verified.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.368-371
• /
• 2020

In this paper, we propose a linear tapered slot rectifying antenna for a portable UHF-band RFID system. Since the proposed rectifying antenna does not use a dielectric substrate, the planar antenna is implemented with a thin metal thickness. The rectifier circuit converts input RF power into output DC voltage using a voltage doubler circuit based on two anti-parallel schottky diodes. The rectifying antenna is integrated by the voltage doubler circuit into a linear tapered slot antenna. For conjugate impedance matching of the rectifying circuit and the linear tapered slot antenna, the source-pull method was utilized by adjusting the angle of the tapered slot and the length of the antenna feed line. The proposed antenna prototype has been verified with the electrical and radiation characteristics through RF-DC conversion and far-field radiation test in open space measurement environment. Finally, the proposed antenna is realized to 0.23-wavelength (75 mm) and 0.18-wavelength (60 mm) at 915 MHz center frequency.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.412-415
• /
• 2015

This paper presents a MPPT(Maximum Power Point Tracking) control CMOS interface circuit for vibration energy harvesting. The proposed circuit consists of an AC-DC converter, MPPT Controller, DC-DC boost converter and PMU(Power Management Unit). The AC-DC converter rectifies the AC signals from vibration devices(PZT). MPPT controller is employed to harvest the maximum power from the PZT and increase efficiency of overall system. The DC-DC boost converter generates a boosted and regulated output at a predefined level and provides energy to load using PMU. A full-wave rectifier using active diodes is used as the AC-DC converter for high efficiency, and a schottky diode type DC-DC boost converter is used for a simple control circuitry. The proposed circuit has been designed in a 0.35um CMOS process. The chip area is $950um{\times}920um$.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.267-270
• /
• 2014

This paper presents a CMOS interface circuit for vibration energy harvesting. The proposed circuit consists of an AC-DC converter and a DC-DC boost converter. The AC-DC converter rectifies the AC signals from vibration devices(PZT), and the DC-DC boost converter generates a boosted and regulated output at a predefined level. A full-wave rectifier using active diodes is used as the AC-DC converter for high efficiency, and a schottky diode type DC-DC boost converter is used for a simple control circuitry. A MPPT(Maximum Power Point Tracking) control is also employed to harvest the maximum power from the PZT. The proposed circuit has been designed in a 0.35um CMOS process. The chip area is $530um{\times}325um$. Simulation results shows that the maximum efficiencies of the AC-DC converter and DC-DC boost converter are 97.7% and 89.2%, respectively. The maximum efficiency of the entire system is 87.2%.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.5
• /
• pp.453-456
• /
• 2016

The major causes of electrical fire in low-voltage distribution lines are classified into short-circuit fault, overload fault, electric leakage, and electric contact failure. The special principal factor of the fire is electric arc or spark accompanied with such electric faults. This paper studies the development of an electric fire prevention system with detection and alarm of that in case of parallel arc fault occurrence in low-voltage distribution lines. The proposed system is designed on algorithm sensing the instantaneous voltage drop of line voltage at arc fault occurrence. The proposed detector has characteristics of high-speed operation responsibility and superior system reliability from composition using a large number of semiconductor devices. A new sensing control method that shows the detection of parallel arc fault is sensed to ripple voltage drop through a diode bridge full-wave rectifier at electrical accident occurrence. Some experimental tests of the proposed system also confirm the practicality and validity of the analytical results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.2
• /
• pp.107-117
• /
• 1998

In this paper, a deadbeat controller design technique is developed for the recently introduced PFC(Power Factor Correction) circuit named as a QBSRR(Quantum Boost Series Resonant Rectifier) to achieve the fast dynamic responses of the output voltage in the presense of any load variations. And, in order to monitor the load information without employing the current sensor, the load estimation method is also derived. By using the information of the load estimation method, the proposed controller gain is automatically adjusted to have the system always keep the very fast dynamic responses. To verify these superior performances, the simulation and the experiment are carried out.

• Proceedings of the KIEE Conference
• /
• 2003.11b
• /
• pp.35-42
• /
• 2003

We have studied DC energy conversion of RF card by wireless communication. In order to attain an objective, it used the system which is a Rectenna. The main purpose of energy conversion system is the operation of the circuits at RF-ID system. The proposed RF-ID system is a lot classified with the reader and tag. Reader is a kind of the base station role supporting RF energy. And priority tag convert RF energy from the reader it was delivered with a wireless to DC energy. The energy which is converted like Tag. It transmits to the reader characteristic ID of each card. The tag is mainly divided into rectifier, power module, memory and controller. The FRAM maintains the data like a ROM in no-power situation. And the advantage is a low power element compared with other EEPROM. There are two considerations, when RF energy is converted into DC source by wireless. One is energy amount supported from the reader, the other is high power efficiency. This paper presents a study of simulation and experiments on the RF-DC conversion circuit in tag by the power efficiency concentrated.