• 한국운동역학회지
• /
• 제25권1호
• /
• pp.65-76
• /
• 2015

Objective : The purpose of this study was to analyse the differences in core stability and muscle balance of the pilates Teaser motion according to the surfaces and skills. Methods : There were 10 subjects in this study with 5 being skilled and 5 that were not skilled. The independent variables were surfaces (high elastic & aluminum) and skills (skilled & unskilled). Dependent variables were core stability and muscle balance. Core stability was measured by Force Platform (9872, Switzerland), 3D Imagery (IBS-2000, EXYMA) was used to understand the muscle balance. In order to do the Teaser movement subjects had to lay flat on their back and then lean forward as much as possible and hold the position for 10 seconds. Afterwards, they would lay back down again. A camera (MHS-PM5K, SONY) was used to make 4 phases (take off, recoil forward, holding, recoil backward) during the teaser exercise to analyze movement. In this study quantitative and qualitative analysis was used. For the statistical analysis, 2X2 ANOVA was used to analyze the differences in movement time, X,Y,Z maximum force, center of pressure and angles according to different phases. 2X3 ANOVA was used to analyze the differences in muscle balance via SPSS 18.0. Results : Soft. Elastic mat had a longer holding time, lower Fx/ Fy/ Fz, shorter Fx trajectory, larger angle and shorter gaps in muscle balance than a hard surface in skilled subjects. This was because the mat can help to recruit and then sustain core fine muscles during holding time in the Teaser movement.

• The Korean Journal of Physiology
• /
• 제17권1호
• /
• pp.23-28
• /
• 1983

steroid가 폐절제에 의한 대상성증식기의 폐장의 압력-용적곡선에 어떤 영양을 미칠 것인가를 알아보기 위해 실시한 본 실험의 결과를 요약하면 폐절제군은 대조군에 비해 폐용압률이 증가하였고 폐절제후 반대측폐장의 무게는 대조군에 비해 폐절제군이 유의하게 증가하였고 폐절제후 betamethasone을 투여한 군에 있어서는 대조군에 비해서는 증가하였으나 폐절제군보다는 적게 증가하였다. 또한 이러한 결과들은 betamethasone에 의해 폐포표면활성물질의 분비가 증가하였거나 혹은 betamethasone이 폐장실질의 결합조직의 단백대사에 영향을 미쳐 elastic recoil force가 감소하여 생긴 결과라고 생각된다.

• Nuclear Engineering and Technology
• /
• 제41권5호
• /
• pp.715-722
• /
• 2009

A model to predict failure of designed-to-fail (dtf) fuel particles is discussed. The dtf fuel under study consisted of a uranium oxycarbide kernel coated with a single pyrocarbon seal coat. Coating failure was assumed to be due to fission gas recoil and knockout mechanisms and direct diffusive release of fission gas from the kernel, which acted to increase pressure and stress in the pyrocarbon layer until it ruptured. Predictions of dtf fuel failure using General Atomics' particle fuel performance code for HRB-17/18 and HFR-B1 irradiation tests were reasonably accurate; however, the model could not predict the failure for COMEDIE BD-1. This was most likely due to insufficient information on reported particle fuel failure at the beginning.

• Bulletin of the Korean Chemical Society
• /
• 제30권11호
• /
• pp.2661-2664
• /
• 2009

Photodissociation of nitrous oxide near 203 nm has been studied by a combination of high resolution slice ion imaging technique and (2+1) resonance-enhanced multiphoton ionization (REMPI) spectroscopy of $N_2(X^1{{\Sigma}_g}^+)$ via the (a″$^1{{\Sigma}_g}^+$) state. We have measured the recoil velocity and angular distributions of $N_2$ fragments by ion images of the state-resolved photofragments. The $N_2$ fragments were highly rotationally excited and the NN-O bond dissociation energy was determined to be 3.635 eV. Also, we investigated the photofragment images from the photodissociation of $N_2O$ clusters with various stagnation pressures.

• 대한기계학회논문집B
• /
• 제32권11호
• /
• pp.832-840
• /
• 2008

Ablation occurs at irradiance beyond $10^9\;W/cm^2$ with nanosecond and short laser pulses focused onto any materials. Phenomenologically, the surface temperature is instantaneously heated past its vaporization temperature. Before the surface layer is able to vaporize, underlying material will reach its vaporization temperature. Temperature and pressure of the underlying material are raised beyond their critical values, causing the surface to explode. The pressure over the irradiated surface from the recoil of vaporized material can be as high as $10^5\;MPa$. The interaction of high power nanosecond laser with a thin metal in air has been investigated. The nanosecond pulse laser beam in atmosphere generates intensive explosions of the materials. The explosive ejection of materials make the surrounding gas compressed, which form a shock wave that travels at several thousand meters per second. To understand the laser ablation mechanism including the heating and ionization of the metal after lasing, the temporal evolution of shock waves is captured on an ICCD camera through laser flash shadowgraphy. The expansion of shock wave in atmosphere was found to agree with the Sedov's self-similar spherical blast wave solution.

• Journal of Welding and Joining
• /
• 제26권6호
• /
• pp.67-73
• /
• 2008

Three-dimensional transient simulation of laser-GMA hybrid welding involving multiple physical phenomena is conducted neglecting the interaction effect of laser and arc heat sources. To reproduce the bubble and pore formations in welding process, a new bubble model is suggested and added to the established laser and arc welding models comprehending VOF, Gaussian laser and arc heat source, recoil pressure, arc pressure, electromagnetic force, surface tension, multiple reflection and Fresnel reflection models. Based on the models mentioned above, simulations of laser-GMA hybrid butt welding are carried out and besides the molten pool flow, top and back bead formations could be observed. In addition, the laser induced keyhole formation and bubble generation duo to keyhole collapse are investigated. The bubbles are ejected from the molten pool through its top and bottom regions. However, some of those are entrapped by solid-liquid interface and remained as pores. Those bubbles and pores are intensively generated when the absorption of laser power is largely reduced and consequently the full penetration changes to the partial penetration.

• 한국의학물리학회지:의학물리
• /
• 제20권3호
• /
• pp.119-124
• /
• 2009

스텐트는 인체내 비혈관 또는 혈관의 내강에 직접 삽입되어 장기간 내강의 개통을 확보해 주어야 하는 보형기구로 체내에서의 안정성이 매우 중요하다. 스텐트의 성능은 크게 radial force, shortening, anti-migration, 방사선 불투과성, 유연성, 회복력, 삽입기구의 굵기 및 삽입 용이성 등의 항목으로 평가된다. 현재 스텐트는 다양한 제품이 널리 사용되어지고 있으며, 병변에 따라 선택이 가능하다. 스텐트는 개통이라는 고유 목적을 달성하면서 시술의 편의성이 고려되는 데 스텐트의 radial force와 유연성, 그리고 삽입기구의 유연성이 중요하다고 할 수 있다. 최근에 유한요소 해석법을 이용한 스텐트의 기계적 특성을 평가하기 위한 연구는 상당량 진행되어 왔다. 그러나 유한요소 해석법을 이용한 스텐트의 피로 거동 분석을 위한 전산 모사에 관한 연구는 드물다. 특히, 세선형 스텐트의 연구 및 시술 이후의 안정성에 대한 연구는 거의 없는 실정이다. 따라서 본 연구에서는 비혈관용 세선형 스텐트에 대하여 유한요소 해석법을 이용한 전산모의실험을 통한 피로특성 분석을 수행한 결과 해당 제품이 목표 수명을 지나서 피로 파괴(내구지수 : 1.74)가 발생한다고 예측할 수가 있었다. 이러한 유한요소 해석법은 스텐트 시술시의 장기적 안정성을 확보함으로써 산업체의 스텐트 개발 기간 및 예산 절감 등 경제적 개발에 많은 도움이 될 수 있을 것이다.

• 한국레이저가공학회지
• /
• 제14권1호
• /
• pp.14-18
• /
• 2011

Semiconductor industry demands decrease in line/space dimensions of IC substrates. Particularly for IC substrates for CPU, line/space dimensions below $10{\mu}m/10{\mu}m$ are expected to be used in production since 2014. Conventional production technologies (SAP, etc.) based on photolithography are widely agreed to be reaching capability limits. To address this limitation, the embedded circuit fabrication technology using laser ablation has been recently developed. In this paper, we used a nanosecond UV laser and a picosecond UV laser to fabricate embedded circuit patterns into a buildup film with $SiO_2$ powders for IC substrate. We conducted SEM and EDS analysis to investigate surface quality of the embedded circuit patterns. Experimental results showed that due to higher recoil pressure, picosecond UV laser ablation of the buildup film generated a better surface roughness.

• 한국레이저가공학회지
• /
• 제15권3호
• /
• pp.7-10
• /
• 2012

Dimensions (line/space) of circuits in IC substrates for high-end chips (e.g. CPU, etc.) are anticipated to decrease as small as $10{\mu}m/10{\mu}m$ in 2014. Since current etch-based circuit-patterning processes are not able to address the urgent requirement from industry, laser-based circuit patterning processes are under active research in which UV laser is used to engrave embedded circuits patterns into IC substrates. In this paper, we used a nanosecond UV laser to directly fabricate embedded circuit patterns into IC substrates with/without ceramic powders. In experiments, we engraved embedded circuit patterns with dimensions (width/depth) of abut $10{\mu}m/10{\mu}m$ and $6{\mu}m/6{\mu}m$ into the IC substrates. Due to the recoil pressure occurring during ablation, the circuit patterning of the IC substrates with ceramic powders showed the higher ablation rate.

• 한국레이저가공학회:학술대회논문집
• /
• 한국레이저가공학회 2004년도 추계학술대회논문집
• /
• pp.22-28
• /
• 2004

Pit and rim formation on the Acrylonitrile Butadiene Styrene(ABS) plastic surface was evaluated after it was irradiated by $CO_2$ and Nd:YAG laser beams. Our results show that thermal effect floor was well observed at the outer wall of pit with $CO_2$ laser irradiated while it was not the case with Nd:YAG laser irradiated. Also the volume and depth of pit formation increase proportionally with the energy intensities of two laser irradiations, but there are significant differences in the slope, width, and FWHM of the Pit formation with two types of laser irradiations. This result shows that $CO_2$ laser irradiation leads to better cooling contraction effect while Nd:YAG laser irradiation induces better recoil pressure effect during the interaction between ABS plastic and laser beam irradiation. The shape of the laser marking could vary significantly depending on the traveling path of molten plastic during injection molding of ABS plastic. Therefore, the selection of material and molding process can have a great impact on the performance of optical storage media.