• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1006-1007
• /
• 2015

Recent improvement in semiconductor technology make efficient switching possible at higher frequencies, which benefits the application of wireless inductive energy transfer. However, a higher frequency does not alter the magnetic coupling between energy transmitter and receiver. Due to the still weak magnetic coupling between transmitting and receiving sides that are separated by a substantial air gap, energy circulates in the primary transmitting side without being transferred to the secondary receiving side. This paper proposes an analysis on the system efficiency to determine the optimal impedance requirement for coils, rectifier and DC-DC Converter. A novel Boost DC-DC Converter is designed to provide the optimal impedance matching in WPT(Wireless Power Transfer) system for various loads.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.1
• /
• pp.75-81
• /
• 2012

In this paper, the wireless power transfer system using the magnetic resonance was designed, analyzed by circuit analysis methode and the calculated transfer function was compared with the measured one. The self-resonant coil was made up of the commonly used capacitor which had the lumped capacitance and it enabled the stable magnetic resonance not to be affected by the circumstance. The transmission efficiency of this system was 70[%] at the 15[cm] between the transmission and receiving coil and the measured transfer function was similar to the calculated one, which means the circuit analysis methode is valid in this system. When the intermediate coils were added between the transmission and receiving coil, the transmission efficiency was increased, which produced the increase of transfer distance. In the case of the five intermediate coils adding, the 35[%] transmission efficiency was achived at the 90[cm] distance.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.2
• /
• pp.213-218
• /
• 2022

In this paper, a technology for a high-efficiency wireless power transmission transmitting and receiving coil that can wirelessly charge a drone is introduced. The drone station implements the ability to charge the battery wirelessly without the need to remove the battery to charge the drone's battery. In order to charge the drone's battery in the shortest time, wireless charging efficiency must be high. In order to increase the wireless charging efficiency of the drone station, a method for manufacturing high-efficiency transmitting and receiving coils and a performance measurement method are presented. Transmitting and receiving coils were manufactured considering the size and weight of the drone so as not to interfere with the flight of the drone. Efficiency of 88% or more was realized at a distance of 40mm or more between the transmitting and receiving coils.

• JOURNAL OF ELECTRICAL WORLD
• /
• no.12 s.120
• /
• pp.4-9
• /
• 1986

• JOURNAL OF ELECTRICAL WORLD
• /
• no.12 s.120
• /
• pp.10-14
• /
• 1986

• JOURNAL OF ELECTRICAL WORLD
• /
• no.12 s.108
• /
• pp.44-48
• /
• 1985

• Proceedings of the KIPE Conference
• /
• 2002.11a
• /
• pp.65-68
• /
• 2002

Most of the present demand in the world is met by fossil and nuclear power plants. A small part is met by renewable energy technologies. Among the renewable power sources, wind and solar energy have experienced a remarkably rapid growth in the past 10 years. Recently the utilization of wind power has been receiving close attention in this country, especially for the electrification of off-shore islands. The objective of this study is to demonstrate a small wind energy system as a stand-alone power source.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.19 no.3
• /
• pp.497-506
• /
• 2024

In this paper, medium-power wireless power transmission is implemented using the commercial power frequency (60 Hz). Since general magnetic induction wireless power transmission devices use more than several tens of kHz, the commercial power frequency (60 Hz) cannot be used as is. Therefore an AC/DC converter is used to convert the 60 Hz power frequency into DC, and a high-frequency power amplifier is used to convert DC into several tens of kHz. In magnetic induction wireless power transmission, the AC/DC converter and high-frequency power amplifier are removed, and a extremely low frequency wireless power transmission(ELF-WPT) system using commercial frequency consisting of only transmitting resonance tank, transmitting coil, receiving resonance tank, and receiving coil is implemented, and verified through wireless power transmission experiments.

• Journal of Korea Society of Industrial Information Systems
• /
• v.14 no.1
• /
• pp.9-16
• /
• 2009

In this paper, a method is proposed for the analysis of radiowave receiving characteristics of an ammunition with electric detonator. In this method, an ammunition with electric detonator is modelled as a receiving antenna with its gain obtained by computer simulation or measurement. The induced radiowave power is obtained by inserting the gain of the electric detonator in the antenna coupling formula. Radiowave receiving characteristics at very close distances are obtained by Treasuring the transmission coefficient between a half-wave dipole and the electric detonator model. Radiowave receiving characteristics of the electric detonator in a 105mm tank ammunition are obtained using the proposed method and the safety of the 900 MHz RFID reader on the detonator is assessed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.5
• /
• pp.739-745
• /
• 2015

In this paper, a flexible wireless power receiving system is proposed for wearable device applications. The proposed system is designed with printable component configuration to be integrable to textile material. While the defected ground structures(DGSs) are utilized for planar printable filter designs, direct impedance matching technique is considered for flexible circuit performance. The proposed system has been implemented on a flexible substrate with a thickness of 5 mils, and experimented for power conversion efficiencies and converted voltages. In order to evaluate the hardware flexibility, the system performance are measured a bended circuit board at a radius of curvature of 5 cm. The system performance is analyzed for the degradation due to the curvature. The proposed system has shown the excellent capability of far-field wireless power transfer systems in flexible device environments.