• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.98-100
• /
• 2005

This paper describes link analysis on the processed data, HRIT (High Rate Information Transmission) and LRIT (Low Rate Information Transmission), for the preliminary design of interface between COMS (Communication, Ocean and Meteorological Satellite) and ground station. At the MODAC (MeteorologicaVOcean Data Application Center), the processed data are transmitted to user station via COMS with normalization and calibration by pre-processing of MI (Meteorological Imager) data. Due to consider satellite as radio relay, overall analysis containing uplink and downlink is needed. Specific link parameters can be obtained with using the outcomes of SRR (System Requirement Review) which was held on 13-14 June 2005, in Toulouse. From the relation between overall link margin and output power of HPA (High Power Amplifier) of MODAC, it is shown that even though the minimum power related with COMS receiving power range is transmitted at MODAC, the obtained link margin of HRIT could be above 3 dB at user station which antenna elevation angle is 10 degree.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.9
• /
• pp.57-63
• /
• 2007

The occurrence of a corona is that electrical discharge due to the heterogeneity that occurs when an electrical field is concentrated in an electrode due to a cusp formed on said electrode. Wire treatment at the end of a 154[kV] dead end clamp for end users accelerates the occurrence of corona, which in turn leads to power loss and noise. In this study, the characteristics of the corona which occurs between porcelain insulators and support clamps of overhead lines used in 154[kV] power receiving facilities for end users were investigated. The corona, which cannot be identified by one common method, was measured utilizing a UV image camera. A risk assessment for fire damage and its status was suggested. The stress distribution of the electrical field by length of bare wire was suggested by means of the finite element method(FEMLAB). As a result, it was found to affect a porcelain insulators. These results can be utilized for the enhancement of clamp installation and safety in power facilities.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.2
• /
• pp.76-81
• /
• 2011

Power system frequency is the main index of power quality indicating an abnormal state and disturbances of systems. The nominal frequency is deviated by sudden change in generation and load or faults. Power system is used as frequency relay to detection for off-nominal frequency operation and connecting a generator to an electrical system, and V/F relay to detection for an over-excitation condition. Under these circumstances, power system should maintain the nominal frequency. And frequency and frequency deviation should accurately measure and quickly estimate by frequency measurement device. The well-known classical method, frequency estimation technique based on the DFT, could be produce the gain error in accuracy. To meet the requirements for high accuracy, recently Wavelet transforms and analysis are receiving new attention. The Wavelet analysis is possible to calculate the time-frequency analysis which is easy to obtain frequency information of signals. However, it is difficult to apply in real-time implementation because of heavy computation burdens. Nowadays, the computational methods using the Wavelet function and transformation techniques have been searched on these fields. In this paper, we apply the Recursive Discrete Wavelet Transform (RDWT) for the frequency estimation. In order to evaluate performance of the proposed technique, the user-defined arbitrary waveforms are used.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.11
• /
• pp.1523-1529
• /
• 2018

Electric vehicles that are currently in operation are being produced domestically. Therefore, there is no great difficulty in receiving or repairing the failed parts or in the overall repair. On the other hand, most of the electric locomotives are manufactured by introducing the parts and technology of foreign vehicle manufacturers. In this paper, conducted a study about life cycle cost analysis of developed auxiliary power unit in 8200 series electric locomotive and suggested cost down method. This confirms the economic benefits of the developed products of the auxiliary power supply compared to the existing products. In addition, a sensitivity analysis of MTBF was conducted to suggest a life cycle cost down method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.5A
• /
• pp.502-510
• /
• 2011

In this paper, we propose a slot scheduling algorithm for balancing power consumption in tree-based sensor networks. In this type of networks, nodes with lower depths tend to consume more energy than those with higher depths, thereby reducing the life time of the network. The proposed algorithm allocates a series of receiving slots first and then a series of sending slots. This way of slot allocation eases packet aggregation and filtering, and thus reduces traffic load on nodes near a sink. We compare the proposed algorithm and the frame-slot allocation algorithm employed in the TreeMAC by resorting to simulation. The simulation results showed that the proposed approach well achieves the balancing of power consumption.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.3
• /
• pp.264-273
• /
• 2005

Broadband power line communications have been receiving tremendous interest In recent years because this technology enables utilities to deploy a communication network over existing power line infrastructures. Despite the enormous potential, there is some skepticism about the technology and its commercial viability. In this paper, we investigate the performance characteristic of PLC through field test carried out in actual households. Also it addresses major field deployment aspects, such as range, coverage, the number of node for operation and maintenance.

• Journal of Advanced Navigation Technology
• /
• v.12 no.6
• /
• pp.634-639
• /
• 2008

In mobile communication networks, the main power consumption is due to the actual transmissions power. Therefore, power efficiency network structures have gained considerable importance in mobile multi-hop systems and networks in recent years. In this paper, the performance of mobile multi-hop wireless system with M-QAM signal and forward error control (FEC) technique are analyzed The FEC technique uses extra processing power related to encoding and decoding, it is need complex functions to be built into the communication node. The probability of receiving a correct bit and codeword for relaying a data frame over h hop relay station to the final station is evaluated as a function of channel parameter and number of hops, and the distance between the different station.

• Journal of Internet Computing and Services
• /
• v.9 no.2
• /
• pp.43-50
• /
• 2008

In IEEE 802.11b wireless LAN, stations keep synchronization by receiving beacons being periodically sent by the AP (access point) when they run in low power mode. Beacon transmission is delayed if wireless channel is busy at a scheduled TBTT (target beacon transmission time), and stations must be awake until they receive the delayed beacon. In this paper, we propose a scheme that stations get their transmission delayed if they have little time for successful data transmission by the next TBTT. Beacon transmission without delay is guaranteed at every TBTT with this method so that the awake time of low power stations to receive beacon can be reduced. The proposed method is simulated and its characteristics ore described with the analysis of the results. The measured results in terms of beacon delay show some enhancement in energy consumption.

• Convergence Security Journal
• /
• v.13 no.4
• /
• pp.27-32
• /
• 2013

In this paper, technologies applied to design urination detection device on diaper that issues an alarm signal to guardian within 10~20m are introduced. It features power saving that uses both low power bluetooth v4.0 chip and low-power program scheme that makes sensor and mirco-controller to be sleep mode while data is not receiving from sensor. Urination detection algorithm that utilizes the difference between previous sensing data and current values is used to improve the degree of the detection precision level. The device designed with the suggested technologies shows the performance that is 100ml of the minimum urine amount for detection, more than 90% of urination detection degree, and 100% of wireless communication success rate.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.10 no.3
• /
• pp.135-146
• /
• 1985

The error rate equation of MSK(Minimum Shift Keying) signal transmitted through the fading channel has been derived in the interference and impulsive noise environments. The error rate performance of MSK system have been evaluated and shown in figures as parameters of carrier-to-noise power ratio(CNR), carrier-to-interferer power ratio(CIR), impulsive index, the ratio of Gaussian noise power component to impulsive noise power component, and fading figure. The results show that, in the fading environment, the error is occurred more frequently by Gaussian noise in the deep fading, however in the shallow fading, impulsive noise is more dominant than Gaussian noise. And in thepresence of interference and fading, interferer deteriorates the MSK receiving system severely even if the interferer is weak.