• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.4
• /
• pp.105-113
• /
• 2010

In this paper, a 1.485 Gbps video signal transmission system using the carrier frequency of 240 GHz band was designed and simulated. The sub-harmonic mixer based on Schottky barrier diode was simulated in the transmitter and receiver. Both of heterodyne and direct detection receivers were simulated for each performance analysis. The ASK modulation was used in the transmitter and the envelop detection method was used in the receiver. The transmitter simulation results showed that the RF output power was -11.4 dBm($73{\mu}W$), when the IF input power was -3 dBm(0.5 mW) at the LO power of 7 dBm(5 mW) in sub-harmonic mixer, which corresponds to SSB(Single Side Band) conversion loss of 8.4 dB. This value is similar to the conversion loss of 8.0 dB(SSB) of VDI's commercial model WR3.4SHM(220~325 GHz) at 240 GHz. The combined transmitter and receiver simulation results showed that the recovered signal waveforms were in good agreement to the transmitted 1.485 Gbps NRZ signal.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.3
• /
• pp.75-82
• /
• 2010

Korea has made a plan to allocate CH 14~CH 51 (470 MHz~698 MHz) for DTV. This paper assumes that DTV operates on CH 51 (692 MHz~698 MHz) and CDMA system operates on CH 52 (698 MHz~704 MHz) in spare band. Minimum Coupling Loss (MCL) method to get protection distance and Spectrum Engineering Advanced Monte Carlo Analysis Tool (SEAMCAT) to get guard band through 5 % interference probability are used. The protection distance is required to be 665.67 km at close frequency offset of 698.625 MHz between DTV transmitter and CDMA Base Station (BS) receiver. The required guard band between DTV transmitter and CDMA Mobile Station (MS) receiver is 5 MHz for the worst case of rural environment. There is no serious impact between CDMA MS transmitter and DTV receiver. The required guard band between CDMA BS transmitter and DTV receiver is 6.25 MHz for the worst case of urban environment. The analysis results may offer a reference and be helpful for considering interference between DTV and other communication systems.

• Journal of Satellite, Information and Communications
• /
• v.7 no.1
• /
• pp.75-81
• /
• 2012

This study is to design the transmitter and receiver of short range UWB(Ultra Wide Band) imaging radar that is able to display high resolution radar image for front area of a UGV(Unmanned Ground Vehicle). This radar can help a UGV to navigate autonomously as it detects and avoids obstacles through foliage. The transmitter needs two transmitters to improve the azimuth resolution. Multi-channel receivers are required to synthesize radar image. Transmitter consists of high power amplifier, channel selection switch, and waveform generator. Receiver is composed of sixteen channel receivers, receiver channel converter, and frequency down converter, Before manufacturing it, the proposed architecture of transceiver is proved by modeling and simulation using several parameters. Then, it was manufactured by using industrial RF(Radio Frequency) components and all other measured parameters in the specification were satisfied as well.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.2
• /
• pp.43-48
• /
• 2011

Cognitive radio is accepted as an effective and promising approach for resolving the spectrum scarcity problem by allowing secondary users to borrow unused spectrum from primary users. A method of identifying busy and empty spectrum at the given time and space, which is called spectrum sensing, constitutes an essential element of the cognitive radio. In this paper, we propose a receiver-centric spectrum sensing scheme which attempts to detect the primary receiver rather than the primary transmitter. It is shown that the proposed receiver-centric sensing approach results in more efficient spectrum utilization than the conventional transmitter-centric sensing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.1088-1092
• /
• 2002

This paper introduces that domestic animals can be effectively administered with an individual recognition system. The system was constructed in original code transmitter, receiver, personal computer, micro-processor, and RS485 telecommunications module. In the individual recognition system. the signal including encoded information about a milk-cow was transmitted from an original code transmitter to a micro-processor through RS485 telecommunications module. The transmitted signal was successfully displayed in a personal computer.

• 한국정보통신설비학회:학술대회논문집
• /
• 2009.08a
• /
• pp.242-247
• /
• 2009

In this paper, we investigate interference between short-range radiocommunication devices (SRDs) with frequency hopping spread spectrum (FHSS) and direct sequence spread spectrum (DSSS) methods when they are in the same frequency bands. In order to analyze interference from unwanted emission of SRD with DSSS to that of FHSS, Monte-Carlo (MC) simulation method is employed and interference probabilities are calculated. We simulate interference scenarios in accordance with several duty cycles and bandwidths. It is also assumed that the propagation model is free space The effect of distance between interfering transmitter and victim receiver is analyzed and bit error rate (BER) is simulated. From the interference analysis results, it is shown that duty cycle affects compatibility more than bandwidth does. Also, we can make sure of the separation distance which satisfies BER criterion when there are only one interfering transmitter and multiple interfering transmitters.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.9
• /
• pp.1184-1201
• /
• 1995

Two multiple access protocols are proposed for a multichannel WDM optical fibre local area network or metropolitan area network in which users are interconnected using a passive star topology. Each user has a single tunable transmitter and a single tunable receiver. A transmitter sends a control packet before its data packet transmission so that its intended receivers can tune to the proper data channel wavelength. The maximum throughput of the proposed protocols are independent of the effective normalized propagation delay which may include the transmitter and receiver tuning times and the processing delays. The maximum throughputs of the protocols are analyzed and compared with those of the existing ones by numerical examples. The message delay of the R- Aloha/synchronous N-server switch protocol which is suitable for the queued users is also analyzed.

• Journal of Biosystems Engineering
• /
• v.24 no.1
• /
• pp.75-80
• /
• 1999

Signal separation and transmission are essential for automatic breeding management of domestic animals. Electronic identification system could transmit the signal of an individual within a defined range to a personal computer by an electromagnetic signal recognition method. Signals for individual recognition were originated by controlling 12 tri-state pins of IC(PT2262) in a transmitter. PT 2262 can generate 4,096 codes. These encoded signals were modulated and transmitted with wireless lines from the transmitter. Then they were demodulated in a receiver, and the signals were transmitted to the micro-processor through an interface and were identified in a PC.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.10
• /
• pp.896-900
• /
• 2013

In this paper, we develop a dust detection sensor system capable of identifying types of dust for an improvement of a robot vacuum cleaner. The dust detection sensor system is composed of a set of infra-red sensors: a single transmitter and multiple receivers. Given the fixed amount of light transmitted from the transmitter, the amount of light coming in multiple receiver sensors varies, depending on the type and density of dust that is passing between the transmitter and the receivers. Therefore, the type of dust can be identified by means of observing the change of the amount of light from the receiver sensors. For experiments, we use two types of dust, rice and sesame, and validate the effectiveness of the proposed method.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.6 no.1
• /
• pp.51-56
• /
• 2013

In this paper, we had design the module of the LED-based media transmission mechanics visible light communication system. To implement the media transmission system through visible light communication transmitter, receiver module the using high brightness, we proposed visible light communication system to implement communication distance of up to a maximum transmitter-receiver distance using a variable PD sensor to the receiver and 1~12 the LED light-emitting device to the transmitter. It was increased efficiency of approximately 20% by measuring the performance during lens wearing or not wearing on the LED module to improve the efficiency of the media transmission system.