• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.31-39
• /
• 1996

The effect of rear-spoiler attached at rear end of automobile trunk on the aerodynamic characteristics of a MIRA reference car model was experimentally investigated. For different shapes and positions(G/H) of the rear-spoiler, the aerodynamic forces on the automobile were measured at various flow speed(ReL). The effect of rear-spoiler on the wake structure behind the automobile was also investigated using flow visualization and hot-wire anemometer. The rear-spoiler modifies the near wake structure and decreases aerodynamic drag and increases driving stability compared with those of the conventional automobile without rear-spoiler. From the experimental results, rear-spoiler of airfoil shape installed at the position of G/H=0.084 shows the best aerodynamic performance.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1825-1829
• /
• 2004

A numerical simulation was performed of flow behind a squareback car with a rear spoiler. Influence of the rear spoiler on drag force has been studied. A lattice Boltzmann method was utilized to portray the unsteady aerodynamics of wake flows. The pressure distributions were employed to examine the vortex formation mode against the rear spoiler. It was found that the separation flow at roof end and c-pillar makes three dimensional vortex structures and the rear spoiler increases pressure on the rear glass surface.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.126-133
• /
• 2003

The aerodynamic characteristics of automobiles have received substantial interest recently. Detailed knowledge of the vehicle aerodynamics is essential to improve fuel efficiency and enhance stability at high-speed cruising. In this study, a numerical simulation has been carried out for three-dimensional turbulent flows around a commercial bus body. Also, the effect of rear-spoiler attached at rear end of bus body was investigated. The Wavier-Stokes equation is solved with SIMPLE method in general curvilinear coordinates system. RNG $k-\varepsilon$ turbulence model with the MARS scheme was used for the evaluating aerodynamic forces, velocity and pressure distribution. The results showed details of the three-dimensional wake flow in the immediate rear of bus body and the effect of rear-spoiler on the wake structure. A maximum of 14% reduction in drag coefficient was achieved for a model with a rear-spoiler.

• Composites Research
• /
• v.37 no.2
• /
• pp.86-93
• /
• 2024

The inner foam structure plays an important role in the performance of the carbon-fiber-reinforced plastic (CFRP) rear spoiler used in automobiles. However, there is still a lack of studies for the CFRP-based rear spoiler according to the type of inner foam, especially under the high-speed driving condition. With this motivation, we numerically analyze the performance of the CFRP rear spoiler using various cases of the inner foam under the highspeed driving condition. Here, polymethacrylimide (PMI), polyvinyl chloride (PVC), and styrene acrylonitrile (SAN) resins are employed as the inner foams in this work. The performances are evaluated using the deformation aspects and vibration characteristics when the driving condition is a high-speed condition (200 km/h). Furthermore, to specifically verify the importance of the inner foam in the high-speed condition, we additionally investigate the performance of the CFRP rear spoiler without the inner foam structure (i.e., hollow type). As a result, it is confirmed that among the types of inner foams utilized in this work, the PMI and PVC inner foams have the best deformation aspect and vibration characteristic, respectively. Note that the hollow-type inner foam has inferior performances compared to other inner foams invoked in this study. Consequently, through this study, it can be confirmed that the inner foam structure can significantly improve the performance of the CFRP spoiler under high-speed driving condition (200 km/h), and also that the strengths of the CFRP spoiler can manifest differently depending on the types of inner foam core.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.689-694
• /
• 2018

Recently, fuel consumption efficiency has become the most important issue in the vehicle development process due to the problem of environmental pollution. The air flow patterns of the vehicle body line and rear part are the most important elements affecting the fuel consumption efficiency. Especially, the airflow pattern of the vehicle rear part is the most important design factor to be considered in rear spoiler design. In this paper, the control factors affecting the airflow of the rear spoiler are determined, the airflow sensitivity of these control factors are tested and, then, the optimized control factors to reduce the airflow drag force are proposed. The model of optimized control factors is tested and the values of the optimized control factors are changed by analyzing the S/N ratio and mean value. Finally, the new modified model incorporating the optimized control factors is tested in an air flow tunnel and its ability to decrease the air drag and reduce the cost is verified.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.2
• /
• pp.198-204
• /
• 2016

In this study, a wind tunnel test was conducted to measure the aerodynamic characteristics of a streamline-designed high-speed bus with the change of wind direction and speed and the result is compared with the aerodynamic performance of a commercialized high-speed bus model (Model-0) manufactured by Zyle Daewoo Bus Corp. Aerodynamic performance of the existing rear-spoiler was tested to prove its aerodynamic effect on the test model bus. From the study, it was found that 24.6 % of the total drag of the original bus model (Model-0) was reduced on the streamline-designed model bus(model-1) without the rear-spoiler but only 14.3 % of the total drag was reduced with the spoiler on the streamlined model bus. It means that the rear spoiler does not work properly with the streamlined model bus (model-1) and should be noted that an optimum design of a rear-spoiler of a vehicle is important to reduce the induced pressure drag and increase the driving stability of a vehicle against yaw motion. The experimental outcome was also compared to the previous numerical research result to evaluate the reliability of the numerical algorithm of the aerodynamic performance analysis of a vehicle. The error rate (%) of the numerical result to the experimental output is about 5.4 % and it is due to the simplified body configuration of the numerical model bus. The drag increases at the higher yaw angle because the transparent frontal area of the model vehicle increases and the downward force increases with the yaw angle as well. It has a positive effect to the driving stability of the vehicle but the moderated downward force should be kept for the fuel economy of a vehicle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.7
• /
• pp.149-156
• /
• 1999

In this study, aerodynmaic characteristics of the notch-back and fast-backpassenger vehicle models(1/10~1/12 acale) attached with winglets were experimentally investigated in a low speed wind tunnel. For various positions(X/L). tilted angles($\beta$) of a winglet, the aerodynamic forces on the vehicle model and rear-surface pressures were measured at various flow speeds. Also a flow of model surface was visualized by tuft method. The experimental results showed that winglets effect aerodynamic characteristics of vehicle models. A maximum of 3% reduction in lift coefficient was achieved with winglets at $\alpha$=-30$^{\circ}$. A maximum of 10% reduction in drag coefficient was achieved for a model with winglets and a rear-spoiler.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.555-558
• /
• 2000

Conventional aerodynamic simulations have carried out by using Supercomputer and over a hundred grid point or wind tunnel experiment. It takes s long time to get a result. This paper has dealt on flow characteristics of automobile in the flow field. CFD(Computational Fluid Dynamics) has been able to apply to industrial field in these days. This new method has been applied to the aerodynamic simulation system, a designer has been able to carry out the practical on early designing phase of automobile. This paper has been focused on the necessity of rear-spoiler, the peculiarity of aerodynamic drag, and the level of drive safety.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.5 no.3
• /
• pp.17-22
• /
• 2006

Sunroof is getting widely used in automobiles since it maintains, compare to window, better air circulation as well as less noise while driving in high speed. In this study, we consider an electronic control type spoiler sunroof which slides backward after tilting a rear part of a glass. Installing a wind deflector on the sunroof reduces noise much more effectively. The height of the wind deflector is designed using a boundary theory related to incompressible air layer. The developed wind deflector is investigated experimentally by measuring a wind noise. When the height of the wind deflector is designed by a fixed type, the sunroof maintains a very quiet interior noise over a certain driving speed, nevertheless it produces relatively loud noise in low driving speed.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.08a
• /
• pp.67.4-67.4
• /
• 2008