• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.6
• /
• pp.954-961
• /
• 2010

Ground-based remote sensing can be used as one of the non-destructive, fast, and real-time diagnostic tools for quantifying yield, biomass, and nitrogen (N) stress during growing season. This study was conducted to assess biomass and nitrogen (N) status of paddy rice (Oryza sativa L.) plants under N stress using passive and active ground-based remote sensors. Nitrogen application rates were 0, 70, 100, and 130 kg N $ha^{-1}$. At each growth stage, reflectance indices measured with active sensor showed higher correlation with DW, N uptake and N concentration than those with the passive sensor. NIR/Red and NIR/Amber indices measured with Crop Circle active sensors generally had a better correlation with dry weight (DW), N uptake and N content than vegetation indices from Crop Circle passive sensor and NDVIs from active sensors. Especially NIR/Red and NIR/amber ratios at the panicle initiation stage were most closely correlated with DW, N content, and N uptake. Rice grain yield, DW, N content and N uptake at harvest were highly positively correlated with canopy reflectance indices measured with active sensors at all sampling dates. N application rate explains about 91~92% of the variability in the SI calculated from NIR/Red or NIR/Amber indices measured with Crop Circle active sensors on 12 July. Therefore, the in-season sufficiency index (SI) by NIR/Red or NIR/Amber index from Crop Circle active sensors can be used for determination of N application rate.

• Journal of Environmental Impact Assessment
• /
• v.30 no.4
• /
• pp.225-236
• /
• 2021

The master plan for the Four Rivers Restoration Project (June 2009) was devised, the procedure of pre-environmental review (June 2009) and environmental impact assessment (Nov. 2009), and post-environmental impact survey were implemented, and 4 times audits also inspected. and finally the Ministry of Environment's Four Rivers Investigation and Evaluation Planning Committee proposed the dismantling or partial dismantling of the five weirs of the Geum River and Yeongsan River. But controversies and conflicts are still ongoing. Therefore, this study intend to reestablish the management plan for the four major rivers by reviewing and analyzing the process so far. The results are as follows. First, a cost-benefit analysis should be performed by comparing the water quality impact of weir operation and weir opening. Therefore, it is inevitably difficult to conduct cost-benefit analysis. Second, according to the results of cost-benefit analysis on the dismantling of the Geum River and the Yeongsan River, the dismantling of the weir and the regular sluice gate opening was decided. However, there is a problem in the validity of the decision to dismantle the weir because the cost-benefit analysis for maintaining the weir is not carried out. Third, looking at the change in water quality of 16 weirs before and after the Four Major Rivers Restoration Project, COD and Chl-a were generally deteriorated, and BOD, SS, T-N, and T-P improved. However, in the cost-benefit analysis related to water quality at the time of weir dismantling, only COD items were targeted. Therefore, the cost of BOD, SS, T-N, and T-P items improved after the project were not reflected in the cost-benefit analysis of dismantling weirs, so the water quality benefits were exaggerated. Fourth, in the case of Gongju weir and Juksan weir, most of them are movable weirs, so opening the weir alone can have the same effect as dismantling when the water quality deteriorates. Since the same effect can be expected, there is little need to dismantle the weirs. Fifth, in order to respond to frequent droughts and floods, it is desirable to secure the agricultural water supply capacity to the drought areas upstream of the four majorrivers by constructing a waterway connected to the weir. At present it is necessary to keep weirs rather than dismantling them.

• The Journal of Korean Society for Radiation Therapy
• /
• v.33
• /
• pp.25-33
• /
• 2021

Purpose : The purpose of this study is to evaluate the accuracy and usefulness of the Trigger mode for the Respiratory Gated Radiation Therapy (RGRT) Materials and methods : A QUASAR respiratory phantom that inserted a 3 mm fiducial marker (a gold marker) was used to estimate the accuracy of the Trigger mode. And the 20 bpm was used as reference respiration rate in this study. The marker that placed at the center of the phantom was contoured, and the lower threshold of a gating window was fixed at 2.0 mm using an OBI with Truebeam STx^TM. The upper threshold was measured every 0.5 mm from 1.0 mm to 3.0 mm. The respiration rates were changed every 10 bpm from 10 bpm to 60 bpm. We repeatedly measured five times to check the error rate of the trigger mode in the same condition. Result : The differences of a distance from a peak phase to upper threshold, 1.0 to 3.0 mm at a 20 bpm as a reference for 3 days in a row were 0.68±0.05 mm, 0.91±0.03 mm, 1.23±0.03 mm, 1.42±0.04 mm, and 1.66±0.06 mm, respectively. Measurement result of changes in respiratory rate compared to baseline respiratory rate in maximum absolute difference. The coefficient of determination (R2) to estimate the correlation between the respiration velocity and variation of absolute difference was on average 0.838, 0.887, 0.770, 0.850, and 0.906. The p-values of all the variables were below 0.05. Conclusion : Using Trigger mode during respiratory gated radiation therapy (RGRT), accuracy and usefulness of trigger mode at reference breathing rate were confirmed. However, inaccuracies depending on the rate of breathing it could be uncertain in case of respiration rate is faster than 20 bpm as a standard respiration rate compared to slower than 20 bpm. Consequently, when conducting a RGRT using the trigger mode, real time monitoring is required with well educated respiration.

• Korean Journal of Remote Sensing
• /
• v.38 no.6_3
• /
• pp.1827-1836
• /
• 2022

Disasters that occur unexpectedly are difficult to predict. In addition, the scale and damage are increasing compared to the past. Sometimes one disaster can develop into another disaster. Among the four stages of disaster management, search and rescue are carried out in the response stage when an emergency occurs. Therefore, personnel such as firefighters who are put into the scene are put in at a lot of risk. In this respect, in the initial response process at the disaster site, robots are a technology with high potential to reduce damage to human life and property. In addition, Light Detection And Ranging (LiDAR) can acquire a relatively wide range of 3D information using a laser. Due to its high accuracy and precision, it is a very useful sensor when considering the characteristics of a disaster site. Therefore, in this study, development and experiments were conducted so that the robot could perform real-time monitoring at the disaster site. Multi-sensor module was developed by combining LiDAR, Inertial Measurement Unit (IMU) sensor, and computing board. Then, this module was mounted on the robot, and a customized Simultaneous Localization and Mapping (SLAM) algorithm was developed. A method for stably mounting a multi-sensor module to a robot to maintain optimal accuracy at disaster sites was studied. And to check the performance of the module, SLAM was tested inside the disaster building, and various SLAM algorithms and distance comparisons were performed. As a result, PackSLAM developed in this study showed lower error compared to other algorithms, showing the possibility of application in disaster sites. In the future, in order to further enhance usability at disaster sites, various experiments will be conducted by establishing a rough terrain environment with many obstacles.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.43 no.2
• /
• pp.231-238
• /
• 2023

Since there is a limit to the physically visible horizon that sensors for autonomous driving can perceive, complementary utilization of digital map data such as a Local Dynamic Map (LDM) along the probable route of an Autonomous Vehicle (AV) is proposed for safe and efficient driving. Although the amount of digital map data may be insignificant compared to the amount of information collected from the sensors of an AV, efficient management of map data is inevitable for the efficient information processing of AVs. The objective of this study is to analyze the efficiency of information use and information processing time of AV according to the expansion of the active section of LDM-based static road and traffic information. To carry out this objective, a microscopic simulator model, VISSIM and VISSIM COM, was employed, and an area of about 9 km × 13 km was selected in the Busan Metropolitan Area, which includes heterogeneous traffic flows (i.e., uninterrupted and interrupted flows) as well as various road geometries. In addition, the LDM information used in AVs refers to the real high-definition map (HDM) built on the basis of ISO 22726-1. As a result of the analysis, as the electronic horizon area increases, while short links are intensively recognized on interrupted urban roads and the sum of link lengths increases as well, the number of recognized links is relatively small on uninterrupted traffic road but the sum of link lengths is large due to a small number of long links. Therefore, this study showed that an efficient range of electronic horizon for HDM data collection, processing, and management are set as 600 m on interrupted urban roads considering the 12 links corresponding to three downstream intersections and 700 m on uninterrupted traffic road associated with the 10 km sum of link lengths, respectively.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.35 no.6
• /
• pp.109-120
• /
• 2023

The High-Frequency Radar (HFR) is an equipment designed to measure real-time surface ocean currents in broad maritime areas.It emits radio waves at a specific frequency (HF) towards the sea surface and analyzes the backscattered waves to measure surface current vectors (Crombie, 1955; Barrick, 1972).The Seasonde HF Radar from Codar, utilized in this study, determines the speed and location of radial currents by analyzing the Bragg peak intensity of transmitted and received waves from an omnidirectional antenna and employing the Multiple Signal Classification (MUSIC) algorithm. The generated currents are initially considered ideal patterns without taking into account the characteristics of the observed electromagnetic wave propagation environment. To correct this, Antenna Pattern Measurement (APM) is performed, measuring the strength of signals at various positions received by the antenna and calculating the corrected measured vector to radial currents.The APM principle involves modifying the position and phase information of the currents based on the measured signal strength at each location. Typically, experiments are conducted by installing an antenna on a ship (Kim et al., 2022). However, using a ship introduces various environmental constraints, such as weather conditions and maritime situations. To reduce dependence on maritime conditions and enhance economic efficiency, this study explores the possibility of using unmanned aerial vehicles (drones) for APM. The research conducted APM experiments using a high-frequency radar installed at Dangsa Lighthouse in Dangsa-ri, Wando County, Jeollanam-do. The study compared and analyzed the results of APM experiments using ships and drones, utilizing the calculated radial currents and surface current fields obtained from each experiment.

• Journal of Food Hygiene and Safety
• /
• v.39 no.1
• /
• pp.35-43
• /
• 2024

Numerous methods have been applied to assess the antibacterial effectiveness of hand hygiene products. However, the different results obtained through various evaluation methods have complicated our understanding of the real efficacy of the products. Few studies have compared test methods for assessing the efficacy of hand hygiene products. In particular, reports on ex vivo pig skin testing are limited. This study aimed to compare and characterize the methodologies applied for evaluating hand hygiene products, involving in vitro, ex vivo, and in vivo approaches, applicable to both leave-on sanitizers and wash-off products. Our further aim was to enhance the reliability of ex vivo test protocols by identifying influential factors. We performed an in vitro method (EN1276) and an in vivo test (EN1499 and ASTM2755) with at least 20 participants, against Serratia marcescens or Escherichia coli and Staphylococcus aureus. For the ex vivo experiment, we used pig skin squares prepared in the same way as those used in the in vivo test method and determined the optimal treated sample volumes for sanitizers and the amount of water required to wash off the product. The hand sanitizers showed at least a 5-log reduction in bacterial load in the in vitro test, while they showed little antibacterial activity in the in vivo and ex vivo tests, particularly those with a low alcohol content. For the hand wash products, the in vitro test was limited because of bubble formation or the high viscosity of the products and it showed low antibacterial activity of less than a 1-log reduction against E. coli. In contrast, significantly higher log reductions were observed in ex vivo and in vivo tests, consistently demonstrating these results across the two methods. Our findings revealed that the ex vivo and in vivo tests reflect the two different antibacterial mechanisms of leave-on and wash-off products. Our proposed optimized ex vivo test was more rapid and more precise than the in vitro test to evaluate antibacterial results.

• Journal of Intelligence and Information Systems
• /
• v.19 no.2
• /
• pp.157-175
• /
• 2013

Since Korean government announced 'Smartwork promotion strategy' in 2010, Korean firms and government organizations have started to adopt smartwork. However, the smartwork has been implemented only in a few of large enterprises and government organizations rather than SMEs (small and medium enterprises). In USA, both Yahoo! and Best Buy have stopped their flexible work because of its reported low productivity and job loafing problems. In addition, according to the literature on smartwork, we could draw obstacles of smartwork adoption and categorize them into the three types: institutional, organizational, and technological. The first category of smartwork adoption obstacles, institutional, include the difficulties of smartwork performance evaluation metrics, the lack of readiness of organizational processes, limitation of smartwork types and models, lack of employee participation in smartwork adoption procedure, high cost of building smartwork system, and insufficiency of government support. The second category, organizational, includes limitation of the organization hierarchy, wrong perception of employees and employers, a difficulty in close collaboration, low productivity with remote coworkers, insufficient understanding on remote working, and lack of training about smartwork. The third category, technological, obstacles include security concern of mobile work, lack of specialized solution, and lack of adoption and operation know-how. To overcome the current problems of smartwork in reality and the reported obstacles in literature, we suggest a novel smartwork service model based on NFC(Near Field Communication). This paper suggests NFC-based Smartwork Service Model composed of NFC-based Smartworker networking service and NFC-based Smartwork space management service. NFC-based smartworker networking service is comprised of NFC-based communication/SNS service and NFC-based recruiting/job seeking service. NFC-based communication/SNS Service Model supplements the key shortcomings that existing smartwork service model has. By connecting to existing legacy system of a company through NFC tags and systems, the low productivity and the difficulty of collaboration and attendance management can be overcome since managers can get work processing information, work time information and work space information of employees and employees can do real-time communication with coworkers and get location information of coworkers. Shortly, this service model has features such as affordable system cost, provision of location-based information, and possibility of knowledge accumulation. NFC-based recruiting/job-seeking service provides new value by linking NFC tag service and sharing economy sites. This service model has features such as easiness of service attachment and removal, efficient space-based work provision, easy search of location-based recruiting/job-seeking information, and system flexibility. This service model combines advantages of sharing economy sites with the advantages of NFC. By cooperation with sharing economy sites, the model can provide recruiters with human resource who finds not only long-term works but also short-term works. Additionally, SMEs (Small Medium-sized Enterprises) can easily find job seeker by attaching NFC tags to any spaces at which human resource with qualification may be located. In short, this service model helps efficient human resource distribution by providing location of job hunters and job applicants. NFC-based smartwork space management service can promote smartwork by linking NFC tags attached to the work space and existing smartwork system. This service has features such as low cost, provision of indoor and outdoor location information, and customized service. In particular, this model can help small company adopt smartwork system because it is light-weight system and cost-effective compared to existing smartwork system. This paper proposes the scenarios of the service models, the roles and incentives of the participants, and the comparative analysis. The superiority of NFC-based smartwork service model is shown by comparing and analyzing the new service models and the existing service models. The service model can expand scope of enterprises and organizations that adopt smartwork and expand the scope of employees that take advantages of smartwork.

• Journal of Korean Home Economics Education Association
• /
• v.26 no.4
• /
• pp.85-114
• /
• 2014

The main purpose of this study was to develop teaching and learning plans and a smart textbook for food and nutrition education in Home Economics focusing on 'healthy diet and meal plans' unit in "Technology home Economics" textbooks for 7th graders to evaluate the effectiveness of the instruction conducted with the smart textbook. The content of the study to achieve the purpose is as follows: First, design a smart education-based teaching and learning curriculum for food and nutrition education in Home Economics, focusing on 'healthy diet and meal plans' unit. Second, develop a smart textbook for food and nutrition education based on the teaching and learning curriculum, using a smart content authoring tool. Third, evaluate the effectiveness of the instruction after applying the curriculum in real classroom situations. The results of this study were as follows: First, teaching and learning plans and materials were developed for two units, 'issues regarding teenagers' diet' and 'implementation of a healthy and balanced diet', under 'teenagers' life'. The first unit, 'issues regarding teenagers' diet', dealt with topics such as teenagers' dietary behaviors, nutrition, and health. Learning objectives for this unit were to help students identify and evaluate their own dietary behaviors. The second unit, 'implementation of a healthy and balanced diet', encouraged students to diagnose problems with their diet and plan nutrient rich meals. The objectives for this unit were to help students implement a healthy and balanced diet by providing them with nutrition and dietary guidelines for Koreans, sample meal plans, and guidelines for developing healthy eating habits for teenagers. In order to develop a teaching and learning plans to achieve these objectives, teaching and learning materials including inquiry tasks, materials for group activities, multimedia, applications and various pop-up learning materials were developed. Second, a smart textbook using DocZoom, which was a smart content authoring tool was developed. The textbook dealt with issues regarding teenagers' diet and implementation of a healthy and balanced diet. Multimedia material used in the textbook come from the Ministry of Food and Drug Safety's food and nutrition education web sites and other sources. To develop student-oriented material, relevant video clips were added to the smart textbook to motivate students and enhance their interest in the course. Third, the outcome of this study indicated that the instruction using teaching and learning plans and learning materials with the smart textbook was effective for enhancing students' interest in Home Economics classes (t-value=-3.99, p<.001), creating enthusiasm for learning(t-value = -2.61, p<.05), encouraging self-directed and independent learning(t-value = -4.77, p<.001), and improving students' interest in food and nutrition courses(t-value = -3.83, p<.001). The students' evaluation of the instruction were as follows: the instruction using teaching and learning plans and learning materials with smart textbooks, instead of paper textbooks, helped them save time looking for learning materials; students evaluated that it was easier for them to see and understand video clips and charts. In addition, most students answered that instruction with smart textbooks were more fun and convenient, and they agreed that the courses enhanced their learning experience.

• The Journal of Korean Society for Radiation Therapy
• /
• v.28 no.2
• /
• pp.179-186
• /
• 2016

Purpose : To figure out if the treatment plan for rectum, bladder and prostate that have a lot of interfraction errors satisfies dosimetric limits without adaptive plan by analyzing MR image. Materials and Methods : This study was based on 5 prostate cancer patients who had IMRT(total dose: 70Gy) Using ViewRay MRIdian System(ViewRay, ViewRay Inc., Cleveland, OH, USA) The treatment plans were made on the same CT images to compare with the plan quality according to adaptive plan, and the Eclipse(Ver 10.0.42, Varian, USA) was used. After registrate the 5 treatment MR images to the CT images for treatment plan to analyze the interfraction changes of organ, we measured the dose volume histogram and the changes of the absolute volume for each organ by appling the first treatment plan to each image. Over 5 fractions, the total dose for PTV was $V_{36.25}$ Gy $${\geq_-}$$ 95%. To confirm that the prescription dose satisfies the SBRT dose limit for prostate, we measured $V_{100%}$, $V_{95%}$, $V_{90%}$ for CTV and $V_{100%}$, $V_{90%}$, $V_{80%}$ $V_{50%}$ of rectum and bladder. Results : All dose average value of CTV, rectum and bladder satisfied dose limit, but there was a case that exceeded dose limit more than one after analyzing the each image of treatment. After measuring the changes of absolute volume comparing the MR image of the first treatment plan with the one of the interfraction treatment, the difference values were maximum 1.72 times at rectum and maximum 2.0 times at bladder. In case of rectum, the expected values were planned under the dose limit, on average, $V_{100%}=0.32%$, $V_{90%}=3.33%$, $V_{80%}=7.71%$, $V_{50%}=23.55%$ in the first treatment plan. In case of rectum, the average of absolute volume in first plan was 117.9 cc. However, the average of really treated volume was 79.2 cc. In case of CTV, the 100% prescription dose area didn't satisfy even though the margin for PTV was 5 mm because of the variation of rectal and bladder volume. Conclusion : There was no case that the value from average of five fractions is over the dosimetric limits. However, dosimetric errors of rectum and bladder in each fraction was significant. Therefore, the precise delivery is needed in case of prostate SBRT. The real-time tracking and adaptive plan is necessary to meet the precision delivery.