• Korean Journal of Remote Sensing
• /
• v.33 no.1
• /
• pp.69-77
• /
• 2017

S The need for an automated geo-positioning approach for near real-time results and to boost cost-effectiveness has become increasingly urgent. Following this trend, a new approach to automatically compensate for the bias of the rational function model (RFM) was proposed. The core idea of this approach is to remove the bias of RFM only using tie points, which are corrected by matching with the digital elevation model (DEM) without any additional ground control points (GCPs). However, there has to be a additional evaluation according to the quality of DEM because DEM is used as a core element in this approach. To address this issue, this paper compared the quality effects of DEM in the conduct of the this approach using the Shuttle Radar Topographic Mission (SRTM) DEM with the spatial resolution of 90m. and the National Geographic Information Institute (NGII) DEM with the spatial resolution of 5m. One KOMPSAT-2 stereo-pair image acquired at Busan, Korea was used as experimental data. The accuracy was compared to 29 check points acquired by GPS surveying. After bias-compensation using the two DEMs, the Root Mean Square (RMS) errors were less than 6 m in all coordinate components. When SRTM DEM was used, the RMSE vector was about 11.2m. On the other hand, when NGII DEM was used, the RMSE vector was about 7.8 m. The experimental results showed that automated geo-positioning approach can be accomplished more effectively by using NGII DEM with higher resolution than SRTM DEM.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.04a
• /
• pp.102-108
• /
• 2009

Fossil power plants firing lower grade coals or equipped with modified system for NOx controls are challenged with maintaining good combustion conditions while maximizing generation and minimizing emissions. In many cases significant derate, availability losses and increase in unburned carbon levels can be attributed to poor combustion conditions as a result of poorly controlled local fuel and air distribution within the boiler furnace. In order to develop a on-line combustion tuning system, field test was conducted at operating power boiler. During the field test the exhaust gases' $O_2$, NOx and CO was monitored by using a spatially distributed monitoring grid located in the boiler's high temperature vestibule and upper convective back-pass region. At these locations, the flue gas flow is still significantly stratified, and air in-leakage is minimal which enables tracing of poor combustion zones to specific burners and over-fire air ports. using these monitored information we can improving combustion at every point within the furnace, therefore the boiler can operate at reduced excess $O_2$ and gas temperature deviation, reduced furnace exit gas temperature levels while also reducing localized hot spots, corrosive gas conditions, slag or clinker formation and UBC. Benefits include improving efficiency, reducing NOx emissions, increasing output and maximizing availability. Discussion concerning the reduction of greenhouse gases is prevalent in the world. When taking a practical approach to addressing this problem, the best way and short-term solution to reduce greenhouse gases on coal-fired power plants is to improve efficiency. From this point of view the real time optimized combustion tuning approach is the most effective and implemented with minimal cost.

• Journal of Welding and Joining
• /
• v.11 no.2
• /
• pp.27-41
• /
• 1993

The estimation of nugget sizes was attempted by utilizing the artificial neural networks method. Artificial neural networks is a highly simplified model of the biological nervous system. Artificial neural networks is composed of a large number of elemental processors connected like biological neurons. Although the elemental processors have only simple computation functions, because they are connected massively, they can describe any complex functional relationship between an input-output pair in an autonomous manner. The electrode head movement signal, which is a good indicator of corresponding nugget size was determined by measuring the each test specimen. The sampled electrode movement data and the corresponding nugget sizes were fed into the artificial neural networks as input-output pairs to train the networks. In the training phase for the networks, the artificial neural networks constructs a fuctional relationship between the input-output pairs autonomusly by adjusting the set of weights. In the production(estimation) phase when new inputs are sampled and presented, the artificial neural networks produces appropriate outputs(the estimates of the nugget size) based upon the transfer characteristics learned during the training mode. Experimental verification of the proposed estimation method using artificial neural networks was done by actual destructive testing of welds. The predicted result by the artifficial neural networks were found to be in a good agreement with the actual nugget size. The results are quite promising in that the real-time estimation of the invisible nugget size can be achieved by analyzing the process variable without any conventional destructive testing of welds.

• Journal of Welding and Joining
• /
• v.16 no.5
• /
• pp.119-133
• /
• 1998

To implement full automation in pipe welding, it si most important to develop special sensors and their related systems which act like human operator when detecting irregular groove conditions. In this study, an automatic pipe Gas Metal Arc Welding (GMAW) system was proposed to full control pipe welding procedure with intelligent sensor systems. A five-axes manipulator was proposed for welding torch to automatically access to exact welding position when pipe size and welding angle were given. Pool status and torch position were measured by using a weld-pool image monitoring and processing technique in root-pass welding for weld seam tracking and weld pool control. To overcome the intensive arc light, pool image was captured at the instance of short circuit of welding power loop. Captured image was processed to determine weld pool shape. For weld seam tracking, the relative distance of a torch position from the pool center was calculated in the extracted pool shape to move torch just onto the groove center. To control penetration of root pas, gap was calculated in the extracted pool image, and then weld conditions were controlled for obtaining appropriate penetration. welding speed was determined with a fuzzy logic, and welding current and voltage were determined from a data base to correspond to the gap. For automatic fill-pass welding, the function of human operator of real time weld seam control can be substituted by a sensor system. In this study, an arc sensor system was proposed based on a fuzzy control logic. Using the proposed automatic system, root-pass welding of pipe which had gap variation was assured to be appropriately controlled in welding conditions and in torch position by showing sound welding result and good seam tracking capability. Fill-pass welding by the proposed system also showed very successful result by tracking along the offset welding line without any control of human operator.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.3
• /
• pp.280-287
• /
• 2010

The first Korean satellite launch vehicle, KSLV-I(Korea Space Launch Vehicle-I), was launched for its first flight test on Aug. 25, 2009 from Naro Space Center located in south Jolla province. Because launch vehicles usually fly long range with large amount of propellants aboard, preparation of countermeasures against potential malfunctions during flight is essential in launch operation. In this paper, the flight safety operation, prepared to guarantee flight safety during launch operation of KSLV-I, is presented. Prior to flight test, flight safety analysis is performed to estimate associated risk levels quantitatively, and during flight, flight safety systems are operated to cope with any risky situations. Real-time flight monitoring including computation of instantaneous impact point using tracking data is executed normally and the flight test is completed without activation of flight termination system.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.7
• /
• pp.143-150
• /
• 2020

Recently, many companies are interested in smart factory services. Because various smart factory services are provided by the combination of mobile devices, cloud computing, and IoT services. However, many workers turn away from these systems because most of them are not implemented from the worker's point of view. To solve this, we implemented a development tool that allows field workers to produce their own services so that workers can easily create smart factory services. Manufacturing data is collected in real time from sensors which are connected to manufacturing facilities and stored within smart factory platforms. Implemented development tools can produce services such as monitoring, processing, analysis, and control of manufacturing data in drag-and-drop. The implemented system is effective for small manufacturing companies because of their environment: making various services quickly according to the company's purpose. In addition, it is assumed that this also will help workers' improve operation skills on running smart factories and fostering smart factory capable personnel.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.5
• /
• pp.20-28
• /
• 2014

This paper proposes a faulty node detection scheme that performs collective monitoring of a distributed networked control systems using interval weighting factor. The algorithm is designed to observe every node's behavior collectively based on the pseudo-random Bose-Chaudhuri-Hocquenghem (BCH) code. Each node sends a single BCH bit simultaneously as a replacement for the cyclic redundancy check (CRC) code. The fault judgement is performed by performing sequential check of observed detected error to guarantee detection accuracy. This scheme can be used for detecting and preventing serious damage caused by node failure. Simulation results show that the fault judgement based on decision pattern gives comprehensive summary of suspected faulty node.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.1
• /
• pp.205-214
• /
• 2013

In this paper, we analyzed the various EV charging-infra information(charging status, charging pattern, charging rate, charging fee, etc.) through the charging infra simulator which would be of help to effectively construct the EV charging infrastructure. The proposed simulator virtually made the EV motoring pattern referred to TMS(Traffic Monitoring System) & Ministry of Land, Transport and Maritime Affairs, and analyzed the charging-infra information(amount of charging, accumulated charging fee, etc.) based on vehicle types, charging type, time and days using EV charging-fee list noticed by KEPCO. Through this simulator, we deducted some considerable contents to build the EV charging infrastructure similarly with real environment.

• Journal of the HCI Society of Korea
• /
• v.3 no.1
• /
• pp.1-7
• /
• 2008

Recently researchers have studied mobile physiological sensing device. However, previous works focused on multiple and real time physiological sensing method, instead of aesthetic shape of sensing devices, sensing comfort during monitoring and sensing reliability against the hand motion artifact. In this work, we propose a stone shaped physiological sensing device to monitor the physiological status in a daily life which maximize the aesthetic feeling and sensing comfort and sensing reliability. We proposed stepwise user centered design process for user centric physiological sensing device and evaluated appropriate sensing positions against the hand motion artifacts and pressure from sensors. From the usability test and experiments, we verified the proposed sensing device provides the aesthetic appeals, sensing comfort and sensing reliability. We expect that this work can be applied in the various health care applications in near future.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.10a
• /
• pp.520-523
• /
• 2010

In the field of network sense for the Ubiquitous environment, the technology of RFID is a significant part. Due to the real time processing of information and the property of network, RFID has been used in service field such as distribution, administrative control of physical distribution, remote measuring device, and security, instead of currently used bar-code. The management system of port facilities using the current RFID technology has the effects of reducing working hours and improvement in data processing, but it is not proper for human resource allocation since it is dominantly worked for physical resources. In this paper, we designed and implemented personnel control system using RFID of 2.4GHz in port facilities which presents a monitoring system for safety operation and increase of efficiency using RFID in order to overcome the limitations and problems of current port operation management techniques.