• Journal of the Semiconductor & Display Technology
• /
• v.3 no.2
• /
• pp.17-21
• /
• 2004

Aluminum nitride(AlN) thin films were deposited on silicon substrate by reactive RF magnetron sputtering without substrate heating. We investigated the dependence of some properties for AlN thin film on sputtering conditions such as working pressure, $N_2$ concentration and RF power. XRD, Ellipsometer and AES has been measured to find out structural properties and preferred orientation of AlN thin films. Deposition rate of AlN thin film was increased with an increase of RF power and decreased with an increase of $N_2$ concentration. AES in-depth measurements showed that stoichiometry of Aluminium and Nitrogen elements were not affected by $N_2$ concentration. It has shown that low working pressure, low $N_2$ concentration and high RF power should be maintained to deposit AlN thin film with a high degree of (0002) preferred orientation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.7
• /
• pp.527-534
• /
• 1998

Thin film deposition of InN, which is a less-studied III-nitride compound semiconductor because of the difficulty if crystal growth, was performed by rf reactive sputtering method using In target and $N_2$reactive gas. The structrual, electrical, and optical properties of the produced films were measured and disussed according to the sputtering parameters such as deposition pressure, rf power, and substrate temperature. From the result of deposition pressure, rf power, and substrate temperature, we could obtain optimal conditions of 5m Torr, 60W, $60^{\circ}C$ for preparing InN thin film with high crystallinity, low carrier concentration, and high Hall mobility. The carrier concentration, Hall mobility, and optical bandgap of the fabricated InN thin films at optimal condition were $6.242\times10^{18}cm^{-3}, 212.526cm^2/V\cdot$ｓ, and 1.912eV, respectively.

• Korean Journal of Materials Research
• /
• v.15 no.10
• /
• pp.621-625
• /
• 2005

Effects of rf power, pressure, sputtering gas composition, and substrate temperature on the deposition rate of the $WC_x$ coatings were investigated. The effects of rf power and sputtering gas composition on the hardness and corrosion resistance of the $WC_x$ coatings deposited by reactive sputtering were also investigated. X-ray diffraction (XRD) and Auger electron spectroscopy (AES) analyses were performed to determine the structures and compositions of the films, respectively. The hardnesses of the films were investigated using a nanoindenter, scanning electron microscopy, ana a salt-spray test, respectively. The deposition rate of the films was proportional to rf power and inversely proportional to the $CH_4$ content of $Ar/CH_4$ sputtering gas. The deposition rate linearly increased with increasing chamber pressure. The hardness of the $WC_x$ coatings Increased as rf power increased. The highest hardness was obtained at a $Ar/CH_4$ concentration of $10 vol.\%$ in the sputtering gas. The hardness of the $WC_x$ film deposited under optimal conditions was found to be much higher than that of the electroplated chromium film, although the corrosion resistance of the former was slightly lower than that of the latter.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.3
• /
• pp.117-124
• /
• 2007

The ITO films were deposited on glass substrates by RF-superimposed dc reactive magnetron sputtering and were annealed in $N_2$ vacuum furnace with temperatures in the range of $403K{\sim}573K$ for 30 minutes. Electrical, optical and structural properties of ITO films were examined with varying annealing temperatures from 403 K to 573 K. The resistivity of as-deposited ITO films was $5.4{\times}10^{-4}{\Omega}cm$ at the sputter conditions of applied RF/DC power of 200/200 W, $O_{2}$ flow of 0.2 seem and Ar flow of 0.2 seem. As a result of annealing in the temperature range of $403K{\sim}573K$, the crystallization occurred at 423 K that is lower than the crystallization temperature caused by a conventional sputtering method. And the resistivity decreased from $5.4{\times}10^{-4}{\Omega}cm\;to\;2.3{\times}10^{-4}{\Omega}cm$, the carrier concentration and mobility of ITO films increased from $4.9{\times}10^{20}/cm^3\;to\;6.4{\times}10^{20}/cm^3$, from $20.4cm^2/Vsec\;to\;41.0cm^2/Vsec$, respectively. The transmittance of ITO films in visible became higher than 90% when annealed in the temperature range of $423K{\sim}573K$. High quality ITO thin films made by RF-superimposed dc reactive magnetron sputtering and annealing in $N_2$ vacuum furnace will be applied to transparent conductive oxides of the advanced flat panel display.

• Journal of the Korean Ceramic Society
• /
• v.31 no.6
• /
• pp.643-650
• /
• 1994

Highly [100]-oriented MgO thin films were deposited on Si(100) single crystal substrates by reactive RF magnetron sputtering. The effects of substrate temperature, gas pressure, RF input powder, and gas composition on the characteristics of MgO thin films were studied. The higher substrate temperature and the lower operating pressure were, the better crystallinity of the deposited MgO thin films were. The influences of the RF input power and oxygen to argon ratio were very complex. The physical characteristics of the films changed dramatically with deposition conditions. Highly smooth and epitaxial MgO films were obtained at the deposition conditions as follows; subatrate temperature, $600^{\circ}C$; operating pressure, 10 mtorr; RF input power density, 2 W/$\textrm{cm}^2$; the percentage of oxygen, 10%.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.3
• /
• pp.113-116
• /
• 2007

Titanium dioxide ($TiO_2$) films were deposited by RF reactive magnetron sputtering on non-alkali glass and single crystal MgO (100) substrate at substrate temperature of $400^{\circ}C$. Micro structures of $TiO_2$ films were investigated by XRD, FE-SEM, and Pole figure measurements. $TiO_2$ films deposited on glass substrate showed preferred orientation of anatase (101), whereas $TiO_2$ films deposited on the MgO single crystal substrate showed hetero-epitaxial anatase (100). $TiO_2$ film grown on MgO substrate showed higher photoctalytic activity than that of glass substrate.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.3
• /
• pp.122-125
• /
• 2004

ITO films were deposited on polyethylene terephthalate substrate by a dc reactive magnetron sputtering using rf bias without substrate heater and post-deposition thermal treatment. The dependency of rf substrate bias on plasma sputter processing was investigated to control energetic particles and improve ITO film properties. The substrate was applied negative rf bias voltage from 0 to -80 V. The composition of indium, tin, and oxygen atoms is strongly depended on the rf substrate bias. Oxygen deficiency is the highest at rf bias of -20 V. The electrical and optical properties of ITO films also are dominated obviously by negative rf bias.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.2
• /
• pp.83-89
• /
• 2011

In this study, we investigated the effects of shutter control by Reactive Magnetron Sputtering using Inductively-Coupled Plasma(ICP) for obtaining ZnO thin films with high purity. The surface morphologies and structure of deposited ZnO thin films were characterized using Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM) and X-ray Diffractometer (XRD). Also, optical and chemical properties of ZnO thin films were analyzed by Spectroscopic Ellipsometer (SE) and X-ray Photoelectron spectroscopy (XPS). As a result, it observed that ZnO thin films grown at reactive sputtering using shutter control and ICP were higher density, lower surface roughness, better crystallinity than other conventional sputtering deposition methods. For obtaining better quality deposition ZnO thin films, we will investigate the effects of substrate temperature and RF power on shutter control by a reactive magnetron sputtering using inductively-coupled plasma.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.2
• /
• pp.73-78
• /
• 2004

AIN thin film has been deposited on the $AI_2$$O_3$substrate with reactive radio frequency( RF) magnetron sputtering method. In this work, elelctromechanical coupling coefficient of AIN thin film was increased with an increase of AIN thin film thickness, and the maximum value was 0.11%. Insertion loss of SAW device was decreased with an increase of AIN thin film thickness and the minimum value was 33［㏈］. SAW velocity of IDTs/AIN/$AI_2$$O_3$structure and IDTs/AIN/$AI_2$$O_3$/Si structure were about 5480［㎧］and 5040［㎧］respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.11
• /
• pp.977-982
• /
• 2005

Al/AlN/n-type 6H-SiC (0001) MIS structures were prepared by AlN layers on vicinal 6H-SiC(0001) substrates with reactive RF magnetron sputtering method. The AlN films were annealed at $900^{\circ}C$, $N_2$ atmosphere lot 1 minutes showed the best result. With XRD analysis, AlN(0002) peak was clearly found. The typical dielectric constant value of the AlN film in the MIS capacitors was obtained as 8.4 from photo C-V. Also, the gate leakage current density of the MlS capacitor was $10^{-10}\;A/cm^2$ order within the electric field of 1.8 MV/cm. Finally, the amount of interface trap densities, $D_{it}$, was evaluated as $5.3\times10^{10}\;eV^{-1}cm^{-2}$ at (Ec-0.85) eV.