• Journal of the Korean Ceramic Society
• /
• v.24 no.2
• /
• pp.179-185
• /
• 1987

The microstructure and the electrical conductivity of MgO-doped Cr2O3 were investigated as a function of oxygen partial presure, temperature, and MgO content. The grain size was estimated about 1.0$\mu\textrm{m}$. The solubility limit is increased with oxygen partial pressure. Above the solubility limit of MgO in Cr2O3, the spinel phase(MgCr2O4) is formed by the reaction of MgO and Cr2O3. The electrical conductivity of MgO-doped Cr2O3 within the solubility limit is increased with MgO content. Above the solubility limit, however, it is decreased with increasing MgO content because of the formation of the spinel phase.

• Journal of Electrochemical Science and Technology
• /
• v.10 no.4
• /
• pp.381-386
• /
• 2019

Zn-air battery uses oxygen from the air, and hence, air holes in it are kept open for cell operation. Therefore, loss of water by evaporation through the holes is inevitable. When the water is depleted, the battery ceases to operate. There are two water consumption routes in Zn-air batteries, namely, active path (electrolysis) and passive path (evaporation and corrosion). Water loss by the active path (electrolysis) is much faster than that by the passive path during the early stage of the cycles. The mass change by the active path slows after 10 h. In contrast, the passive path is largely constant, becoming the main mass loss path after 10 h. The active path contributes to two-thirds of the electrolyte consumption in 24 h of cell operation in 4.0 M KOH. Although water is an important component for the cell, water vapor does not influence the cell operation unless the water is nearly depleted. However, high oxygen concentration favors the discharge reaction at the cathode.

• Journal of the Korean Society of Safety
• /
• v.6 no.2
• /
• pp.31-36
• /
• 1991

Quenching effects of acetylene and hydrogen into oxygen detonation by using detonation arrester ［DA］are studied in this paper. The experiments were carried out in cylinderical shock tube. 5m long, 30mm dia., with stolchlometric ratio ［SR］of each gas and 10-l20$\mu$ Cell Size of brass and Stainless Steel of DAs were installed in it To clarify arresting ability correlation with initial pressure, Pi, critical thickness, Tct, and shapes of supporting panel of DA are also investigated It is found that ­detonation velocities has most dependency on Pi, it shows notable changes around 0.5kgf/$\textrm{cm}^2$ for hydrogen, 0.15kgf/$\textrm{cm}^2$ for acetylen respectively, ­DA can be safety device able to arrest shock wave of detonation, ­over Tct flame transmission might be only the factor has to be considered, ­acetylene seems to be much more stronger detonation characteristics than hydrogen because of reaction heat.

• Journal of the Korean Ceramic Society
• /
• v.29 no.5
• /
• pp.377-382
• /
• 1992

For the development of solid oxide fuel cell the joined interface formation between perovskite oxygen electrode and YSZ solid electrolyte is emphasized in the aspect of reducing the undisirable overpotential. The diffusion couple of LaMnO3 and YSZ was prepared by hot pressing at 130$0^{\circ}C$ in the flow of oxygen gas. The high temperature solid state reaction mechanism between LaMnO3 and YSZ is discussed on the basis of the cation composition profile through EDX analysis. The cation components in perovskite compound diffuse considerably into YSZ, while cations of YSZ diffuse little into perovskite.

• Resources Recycling
• /
• v.10 no.1
• /
• pp.42-48
• /
• 2001

The dissolution behavior of gold and silver from gold-silver alloys in aerated cyanide solutions has been investigated by an electrochemical means as well as a direct measurement of gold and silver ions reported in the bulk solution as a function of time using rotating disc electrodes. The variables studied included oxygen partial pressure, rotating speed of the disc, concentration of cyanide, temperature and composition of the allyos. The dissolution potential and the rate of dissolution were obtained in view of the anodic and cathodic current-potential relationships. The results were discussed in terms of the mixed potential theory. The results showed that the dissolution rate of gold and silver from the alloys was controlled partially by chemical reaction. but largely by transport of either oxygen or cyanide, depending on their relative concentration under the experimental conditions employed in this study.

• Journal of Powder Materials
• /
• v.20 no.1
• /
• pp.43-47
• /
• 2013

The extraction of metallic pure vanadium powder from raw oxide has been tried by Mg-reduction. In first stage, $V_2O_5$ powders as initial raw material was reduced by hydrogen gas into $V_2O_3$ phase. $V_2O_3$ powder was reduced in next stage by magnesium gas at 1,073K for 24 hours. After reduction reaction, the MgO component mixed with reduced vanadium powder were dissolved and removed fully in 10% HCl solution for 5 hours at room temperature. The oxygen content and particle size of finally produced vanadium powders were 0.84 wt% and 1 ${\mu}m$, respectively

• 한국연소학회:학술대회논문집
• /
• 2005.10a
• /
• pp.64-68
• /
• 2005

Methane reforming processes to obtain hydrogen were investigated experimentally by using atmospheric plasma source. Among possible reforming processes, such as a $CO_2$ reforming(dry reforming), a partial oxidation (POx), a steam reforming(SR), and a steam reforming with oxygen(SRO or auto-thermal reforming), partial oxidation and the steam reforming with oxygen were considered. We choose a rotating arc plasma as an atmospheric plasma source, since it shows the best performances in our preliminary tests in terms of a methane conversion, a hydrogen production, and a power consumption. Then, the effects of a feeding flow-rate, an electrical power input to a plasma reaction, an $O_2/C$ ratio and a steam to carbon ratio in the case of SRO on the reforming characteristics were observed systematically. As results, at a certain condition almost 100% of methane conversion was obtained and we could achieve the same hydrogen production rate by consuming a half of electrical power which was used by the best results for other researchers.

• Environmental Engineering Research
• /
• v.13 no.1
• /
• pp.14-18
• /
• 2008

Photocatalytic oxidations of benzene gas using the closed system (batch reactor) were induced to determine its by-products and investigate the effect of humidity and oxygen concentration on their generation. The study was able to identify 11 gaseous by-products: 2-methylpropene, acetaldehyde, acetone, pentane, methylcyclobutane, methylcyclopentane, cyclohexane, 2,3-dimethylbutane, 2-methylpentane, 3-methylpentane, and hexane. All the by-products were saturated hydrocarbons, which are less toxic than benzene and were probably formed through hydrogenation reaction on the photocatalytic surface. The photocatalytic oxidation of benzene under higher humidity produced less by-products. However, the amount of acetone released increased with higher humidity and oxygen concentration.

• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.2
• /
• pp.183-190
• /
• 1999

Magnetite was synthesized with $FeSO_4$, and NaOH for the decomposition of carbon dioxide and for the study of the methane formation. The chemical equivalent ratio was changed from 0.5 to 1.50 for the magnetite synthesis. The chemical equivalent ratio was fixed in 1.00, and Nickel chloride and Rhodium chloride equally added and synthesized with the ratio was of 0.10~10.00 mole%. The crystal strucure of the synthesized magnetite was measured XRD. Putting synthesized magnetite in the reactor and using hydrogen gas oxygen-deficient magnetite was made. Injecting carbon dioxide in the reactor, the decomposition reaction was experimented. The formation of methane was confirmed injecting hydrogen gas in the reactor after carbon dioxide was decomposed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.2
• /
• pp.181-184
• /
• 2006

Nd:YAG($\lambda$=266 nm, pulse) laser beam was irradiated on the PDMS surface to improve its chemical reaction, wettability, adhesive property. The various surface modification methods of PDMS were already studied using oxygen plasma, ozone and corona discharge. The surface modification using laser has the advantage of the simple experiment that only directly irradiated laser beam on the PDMS surface in the air. After the laser treatment, the PDMS surface was investigated using a contact angle measuring instrument. The contact angle was decreased with a increase of the surface oxygen content. In conclusion, the wettability of PDMS surface was improved by the laser treatment without changing of its bulk characteristics.