• 열처리공학회지
• /
• 제12권1호
• /
• pp.21-30
• /
• 1999

The present study were investigated changes of precipitation behaviour of laves phase in ferrite single phase and ferrite-martensite dual phase and precipitation of laves phase under stress. Hardness changes in ferrite phase appeared two hardness peaks by precipitation of initial fine precipitator and laves phase in 3Mo-0.3Si and 3Mo-0.3Si-C specimens, respectively. Hardness changes in martensite phase of 3Mo-0.3Si-C specimen was lower in the initial stage of aging by carbide precipitation and after this, increased by re-hardening due to precipitation of laves phase. In the ferrite phase, laves phase was mainly precipitated, whereas in the martensite phase, carbide was preferentially formed during the initial stage of aging and with increasing aging time, laves phase and carbide were simultaneously precipitated by precipitation of laves phase at around carbide. In the ferrite-martensite interface, laves phase was mainly precipitated and carbide was mainly formed at boundary of lath martensite than grain boundary. Adding the stress in aging, fine precipitator of inital precipitation of laves phase precipitated in (100) of perpendicular to tensile direction and has grown to only followed<010>direction and also, volume fraction of laves phase increased. Consequently, the stress added was accelerated initial precipitation of laves phase.

• 한국결정성장학회지
• /
• 제14권1호
• /
• pp.27-32
• /
• 2004

RF-PECVD 방법을 이용하여 DLC(diamond-like carbon)박막을 메탄-수소 가스 혼합비 및 바이어스 전압에 따라 실리콘 웨이퍼 위에 증착하였다. DLC 박막의 결합구조적 특성 및 기계적 성질은 FT-IR, Raman, 그리고 nano-indenter를 이용하여 평가하였다. 혼합가스내 메탄의 유량과 바이어스 전압이 증가함에 따라 증착속도가 증가하였다. 박막내 탄소의 $sp^3/sp^2$ 결합비와 경도는 반응가스내 수소의 유량 및 바이어스 전압이 증가함에 따라 증가하였다.

• 한국주조공학회지
• /
• 제34권5호
• /
• pp.151-155
• /
• 2014

The relatively low conductivity of conventional Mg-Al alloys often limits their areas of application. Therefore, several attempts to develop new high-conductivity magnesium alloys have been made recently. In this research, A Ce-rich rare-earth (RE)material and zinc were added to magnesium which contained no aluminum. As the RE and Zn content were increased, both the hardness and tensile strength were gradually increased, despite the fact that the electrical conductivity decreased slightly. The effects of an aging treatment on the conductivity and mechanical properties of Mg-RE-Zn alloys were also investigated. The electrical conductivity did not change according to the heat treatment conditions; however, the mechanical properties could be enhanced by proper aging heat treatments.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.441-441
• /
• 2007

As Rhenium-Iridium{Re-Ir) coating possesses such features as, high hardness, high elasticity, abrasion resistance and chemical stability, there have been exerted continuous efforts in research works in a variety of fields, and this technology has also been applied widely to industrial areas. In this research, the optimal grinding condition was identified using Microlens Process Machine in order to contribute to the development of aspheric glass lens for mobile phone module having 3 mega pixel and 2.5X zoom, and molding core(WC) was manufactured having performed ultra-precision machining. Effects of Re-Ir coating on form accuracy (P-V) of molding core and surface roughness(Ra) were measured and evaluated.

• Journal of Welding and Joining
• /
• 제19권1호
• /
• pp.65-74
• /
• 2001

A study on the corrosion behavior in case of As-welded and PWHT temperature 55$0^{\circ}C$ of welding part of RE36 steel for marine structure was investigated with parameters such as micro-Vickers hardness, corrosion potential measurement of weld metal(WM), base metal(BM) and heat affected zone(HAZ), both Al anode generating current and Al anode weight loss quantity under sacrificial anode cathodic protection conditions. And also we carried out slow strain rate test(SSRT) in order to research both limiting cathodic polarization potential for hydrogen embrittlement and optimum cathodic protection potential as well as mechanical properties by post-weld heat treatment(PWHT) effect. Hardness of HAZ was the highest among three parts(WM, BM and HAZ) and the highest galvanic corrosion susceptibility was HAZ. And the optimum cathodic polarization potential showing the best mechanical properties by SSRT method was from -770mV to -875mV(SCE). In analysis of SEM fractography, applied cathodic potential from -770mV to -875mV(SCE) it appeared dimple pattern with ductile fracture while it showed transgranular pattern (Q. C : quasicleavage) under -900mV(SCE). However it is suggested that limiting cathodic polarization potential indicating hydrogen embrittlement was under -900mV(SCE).

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권4호
• /
• pp.460-469
• /
• 2000

A study on the corrosion behavior of RE36 steel for marine structure was investigated with parameters such as micro-Vickers hardness, corrosion potential and corrosion current density measurement of weld metal(WM), base metal (BM) and heat affected zone(HAZ), Al anode generating current and Al anode weight loss quantity in case of cathodic protection. And we carried out slow strain rate test(SSRT) in order to research mechanical properties such as stress at maximum load, percent strain, time to fracture and strain to failure ratio etc and to find out limiting cathodic polarization potential for hydrogen embrittlement with applied cathodic polarization potential. Hardness of HAZ part was the highest among those three parts and also galvanic corrosion susceptibility was the highest in HAZ part among those three parts due to the lowest corrosion potential than other parts. However corrosion current density was the highest in WM part among those three parts. And the optimum cathodic polarization potential showing the best mechanical properties obtained by SSRT method with applied constant cathodic potential was from - 770mV to - 875mV(SCE). However it is suggested that limiting cathodic polarization potential indicating hydrogen embrittlement on the mechanical properties was under - 900mV(SCE).

• 대한기계학회논문집A
• /
• 제26권8호
• /
• pp.1690-1697
• /
• 2002

The effects of re-peening on the fatigue damaged material are studied in this paper. The effects of re-peening process on surface hardness, surface roughness, surface compressive residual stress, and fatigue life are investigated. The results can be summarized in brief as follows: The depth of hardening layer was increased by re-peening process. There is no large variation of the surface roughness by re-peening process. The compressive residual stress of shot-peened specimen decreases under the fatigue loading and then increases again by re-peening process. Re-peening process increases the fatigue lifo of shot-peened and fatigue damaged specimen. The increase of fatigue lift under high stress level is much higher than under low stress level.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2011년도 춘계학술대회
• /
• pp.676-677
• /
• 2011

초경합금 성형용 코어를 이용한 고온 압축 성형방식으로 제작되기 때문에 성형용 코어의 초정밀 연산 가공 및 코어면 코팅 기술 개발이 시급한 상황이다. 따라서 본 연구에서는 성형용 초경합금 코어의 연삭가공을 수행하고, 가공 완료된 성형용 코어의 가공면에 Re-Ir 코팅을 수해, 측정을 통하여 코팅면의 마찰 계수 변화에 대한 연구를 수행하였다.

• 한국식품조리과학회지
• /
• 제30권1호
• /
• pp.64-75
• /
• 2014

Freeze-drying process was used for 10 major protein foods referred by the Korea Health Statistics 2011 as follows; chicken, pork, beef, eggs, tofu, squid, soybean, mackerel, anchovy, and pollack/frozen pollack. Boiled samples and re-hydrated samples after freeze-drying were prepared for analysis. The weight variation, the chromaticity, the mechanical texture and sensory properties by eight trained panelists were measured. In the ratio of re-hydration, the anchovy showed the highest value(89.40%), followed by eggs, and squid showed the lowest value(35.51%). Changes of Hunter color value were observed among all samples. For rates on changes of hardness, every sample was increased except for eggs(p<.05). Among the 9 samples, except for eggs, chicken showed the lowest rate of increase in hardness(125.44%) while squid showed the highest rate of increase in hardness(1335.1%). Except for eggs and pork, eight samples represented differences in sensory properties, especially in juiciness and tenderness(p<.05). As a result, we found that egg is the most suitable for freeze-drying among 10 protein sources followed by pork and chicken.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2010년도 춘계학술대회
• /
• pp.828-829
• /
• 2010

초경합금 성형용 코어를 이용한 고온 압축 성형방식으로 제작되기 때문에 성형용 코어의 초정밀 연산 가공 및 코어면 코팅 기술 개발이 시급한 상황이다. 따라서 본 연구에서는 성형용 초경합금 코어의 연삭가공을 수행하고, 가공 완료된 성형용 코어의 가공면에 Re-Ir 코팅을 수해, 측정을 통하여 코팅면이 표면 조도에 미치는 영향에 대하여 연구를 수행하였다.