• Journal of the Korea Concrete Institute
• /
• v.11 no.4
• /
• pp.95-105
• /
• 1999

When superplasticizer is added to manufacture flowing concrete, the base concrete usually needs the adjustment to assure the sufficient fines contained to obtain flowable consistency without excessive bleeding or segregation. However, this may not only increase the cost, but also cause inconvenience in producing the base concrete. In this paper, the experiments are performed on normal base concrete to achieve a segregation-reducing flowing concrete by adding superplasticizer mixed with viscosity agents and AE admixtures. Three kinds of superplasticizer and two kinds of viscosity agent are selected. According to the results, with regard to the performance and cost of the admixtures, melamine type superplasticizer combined with the PEO viscosity agent and AE admixtures at the ratio 1:0.28:0.001 can acquire good quality and reduce the cost in producing the flowing concrete. With proper addition of combined superplasticizer, even though water to cement ratios of the base concrete are different, the segregation-reducing flowing concrete could be also achieved without reproportioning of the base concrete. However, it would be more desirable if the superplasticizer could be adjusted, before it is put into the practical use in order not to cause some other problems, such as rapid rate of slump loss and retarding of setting time.

• YAKHAK HOEJI
• /
• v.32 no.1
• /
• pp.86-94
• /
• 1988

Some rheological properties of subfractions for dextran in the molecular weights range from $3{\times}10^4$ to $2{\times}10^6$ was investigated at room temperature. The dependence of the viscosity on concentration, shear rate, pH & ionic strength, temperature and solvent effect was observed. From the experimental data the Mark-Houwink viscosity equation in water at $25^{\circ}C$ was determined for samples having the molecular weight ranging from $3{\times}10^4$ to $2{\times}10^6$ as$[{\eta}]=3.1{\times}10^{-3}\;Mw^{0.39}(in\;dl/g)$. The intrinsic stiffness of the dextran backbone was estimated by evaluating the 'characteristic ratio' $C_{\infty}$, which is below the 0.082. In the concentrated region, the viscosity was decreased with increasing shear rate and was exponentially decreased with raising temperature, the viscosity showed the maximum value at neutral condition. From the experimental data, it was concluded that dextran chain, linked by the ${\alpha}-1$, 6-glucosidic linkage, behaves like a flexible random coil chain in aqueous solution, dextran solutions were pseudoplastic power law fluids among the empirical models of non-Newtonian behavior. Urea was an active reagent which increases the viscosity and swells dextran while pyrididine and glycerol were inactive reagents. Also, it could be estimated that the formation of gel structure is promote to the neutral state, the molecular weight larger than $2{\times}10^5$, when electrolytic concentration is IN and Ureas is use to solvent.

• The Korean Journal of Community Living Science
• /
• v.23 no.4
• /
• pp.537-552
• /
• 2012

This study was conducted to investigate the quality characteristics of cooked rice with cereals frequently consumed in Korea by blending ratio. Seven kinds of cereals, white rice, glutinous barley, brown rice, black rice, glutinous rice, glutinous foxtail millet and proso millet, were chosen for the study. According to the results from rapid viscosity analyzer, glutinous barley had the lowest pasting temperature($66.55^{\circ}C$) and black rice had the highest values in the peak(231.77 RVU), trough(162.25 RVU), final viscosity(295.81 RVU) and set back(64.05 RVU)(p<0.05). Water absorption rate by soaking time for black rice and brown rice was increased only 18.77% and 14.57%, respectively, even after 120 minutes, whereas those of other cereals were increased up to 20.28~39.32% after 50 minutes. The pasting characteristics of white rice blended with cereals tended to be lower than white rice in the peak, trough, and final viscosity. Textural property of cooked white rice blended with black rice, brown rice, and glutinous foxtail millet showed a significantly higher value for hardness than that of cooked white rice only(p<0.05). The most preferred blending ratio of the respective cereals was 25% for glutinous barley, 10% for black rice, brown rice and proso millet, and 5% for glutinous foxtail millet and glutinous rice in the sensory evaluation for overall quality, but there were no significant differences except glutinous barley, brown rice and glutinous foxtail millet.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.6
• /
• pp.130-138
• /
• 2015

This study was conducted to investigate the effect of the strengthening treatment of methyl cellulose (MC) on properties and aging characteristics of the dewaxed papers during humid heating aging. Beeswax-treated Hanji was dewaxed by the supercritical fluid extraction method, and subsequently the strengthening treatment was performed with MCs having three different viscosities. MC was first applied by dipping a dewaxed paper into a MC solution whose concentration was controlled from 0.5% to 1.5%. After the strengthened papers were artificially aged at $80^{\circ}C$ and 65% RH, the changes in optical and mechanical properties of the samples were evaluated. The results show that viscosity and especially pick-up of MC influenced the strengthening efficiency and aging characteristics of dewaxed paper. Strength was increased with the MC coating weight; in addition, strengthening with MC improved preservability of the dewaxed paper. The optimum conditions for the strengthening with MC was found to be the coating ratio of 4% with 1500 cP MC.

• Korea-Australia Rheology Journal
• /
• v.17 no.4
• /
• pp.165-170
• /
• 2005

In this study, high intensity ultrasound was employed to induce mechano-chemical degradation during melt mixing of polycarbonate (PC) and a series of styrene-acrylonitrile (SAN) copolymers. It was confirmed that generation of macroradicals of constituent polymers can lead to in-situ copolymer formation by their mutual combination, which should be an efficient path to compatibilize immiscible polymer blends and stabilize their phase morphology in the absence of other chemical agents. Based on the effectiveness of the compatibilization by ultrasound assisted mixing process, we investigated the effects of viscosity ratio of PC and SAN and AN content in SAN on the compatibilization of PC/SAN blends. It was found that effectiveness of compatibilization is optimal when the AN content is in the range of favorable interaction with PC and the viscosity of the matrix is higher than that of the dispersed phase. In addition, changes in the interfacial tension between PC and SAN were assessed by examining relaxation spectra which were obtained from measuring rheological properties of ultrasonically treated blends.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1330-1336
• /
• 1990

The factors to act on atomization of liquid fuel are viscosity, geometric shape of nozzle, atomizing pressure, etc. Most of high viscous liquid fuels show decrease in viscosity by raising the preheat temperature, but the viscosity of liquid fuel like CWM does not readily change with fuel temperature. As an experimental study to investigate the atomizing characteristics of CWM, CWM fuel is atomizing with a twin-fluid atomizer, and the effects of the geometric shape of spray nozzle on atomization are investigated by measuring the Sauter`s Mean Diameter (SMD) of CWM. The summarized results obtained in this study are as follows ; (1) As the ratio of the mass flows of atomizing air to that of fuel (W$_{a}$ /W$_{1}$) increases, 능 decreases when fuel temperature is constant. (2) At the ratio (t/d) 4 of thickness (t) of spray nozzle hole to the diameter (d) of the hole, there is the best atomization. And SMD decreases when t/d is between 1 to 4 and increases when t/d > 4.

• Journal of the Korean Ceramic Society
• /
• v.45 no.6
• /
• pp.336-344
• /
• 2008

Rheological properties of cement pastes containing blast furnace slag (BFS: 3,900, $7,910\;cm^2/g$) or fly ash powder (FA: 4,120, $8,100\;cm^2/g$) according to the ratio of water/binder (W/B) and the dosage of polycarboxylate type superplasticizer (PC) were investigated by a mini slump and a coaxial cylinder viscometer. In this experiment, the ratio of replacing OPC with BFS or FA was 30 wt%, the W/B was from 30 to 70 wt%. As a result, the fluidity of cement paste containing BFS or FA was improved with increasing W/B and the dosage of PC. BFS or FA replaced cement paste with W/B 70% and PC 0.3% showed the highest fluidity. The segregation range of cement paste was occurred below $10\;d/cm^2$ of the yield stress and below 50 cPs of the plastic viscosity by the coaxial cylinder viscometer. And also it was formed that the plastic viscosity and the yield stress of FA replaced cement paste were higher than them of BFS replaced cement paste.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.11a
• /
• pp.71-74
• /
• 2005

The viscosity of high-flowability paste is very high compared to normal concrete for the low water-binder ratio(W/B). Therefore, high-flowability concrete is positively necessary to high-range water reducing agent. High-Flowability paste can make much higher fluidity with no occurrence of segregation, by its higher viscosity and lower yield value than normal concrete. The flowability of high-flowability paste must be evaluated not only by convention consistency test such as slump test but also by the base of the rheological properties of the fresh concrete. The purpose of this study is to analyze the fluidity of high-flowability paste according to the addition ratio of the Melamine Sulphonate high-range water reducing agent.; high-flowability paste is considered as Bingham plastic fluid with the rheology parameters of the plaste viscosity and yield value.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.7 s.166
• /
• pp.1075-1084
• /
• 1999

The family of unidirectional continuous fiber reinforced polymeric composites are currently used in automotive bumper beams and load floors. The material properties and mechanical characteristics of the compression molded parts are determined by the curing behavior, fiber orientation and formation of knit lines, which are in turn determined by the mold filling parameters. In this paper, a new model is presented which can be used to predict the 3-dimensional flow under consideration of the slip of mold-composites and anisotropic viscosity of composites during compression molding of unidirectional fiber reinforced thermoplastics for isothermal state. The composites is treated as an incompressible Newtonian fluid. The effects of longitudinal/transverse viscosity ratio A and slip parameter $\alpha$ on the buldging phenomenon and mold filling patterns are also discussed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.7
• /
• pp.853-858
• /
• 2003

The suitable estimation of the filter width in the dynamic eddy viscosity model were investigated in high Reynolds number channel flow. In this study, the improvement on matters by optimizing the test filter shape was attempted through the numerical experiment. The way that select optimum test filter width is recommended. Some test filters, one is based on a discrete representation of the top-hat filter and another are based on a high-order filtering operation, are evaluated in simulations of the turbulent channel flow at Reynolds number 1020, based on friction velocity and channel half width. It appears that the estimation of test filter width practically can decrease the dissipative nature of dynamic eddy viscosity model with explicit test filter. It shows that the value of the filter width ratio used in the dynamic procedure must match the properties of the test filter actually used in the calculation.