• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2003.05a
• /
• pp.39-43
• /
• 2003

Chloride ions are considered to be the major cause of steel corrosion in concrete structures exposed to seashore environments and also permeation of chloride is controlled by chloride diffusion. Therefore, the study on chloride diffusion of concrete have been done so far by many researchers. It is reported that coating material as surface covering material is effect about deterioration of salt damage and carbonation, therefore these materials are important in durability of concrete structure. In this study, corrosion characteristics of reinforcement concrete according to types of surface covering material were evaluated by water-cement ratio, chloride penetration by age on the corrosion area rate and mass decrement of reinforcement. And it is considered that the result of this study on application of the corrosion characteristics of reinforcements under salt damage environmental will be suggested as fundamental data of control performance of salt damage. It is performed that comparison and examination of control performance of salt damage by the corrosion characteristics under salt damage environmental.

• Mycobiology
• /
• v.44 no.1
• /
• pp.54-57
• /
• 2016

Davallialactone (DAVA) is a hispidin analogue derived from the medicinal fungus Phellinus baumii. We examined the effect of DAVA on in vitro fertilization (IVF) of pigs. Boar spermatozoa were incubated in fertilization medium with varying concentrations of DAVA, then sperm motility and reactive oxygen species (ROS) level were evaluated. Higher sperm motility was found following the addition of 0.5 or $1{\mu}M$ DAVA after incubation than addition of other concentrations or controls. ROS level decreased significantly with the addition of DAVA. The rate of normal fertilization was higher in the presence of $1{\mu}M$ DAVA (65.1%) than were those of other concentrations or controls (45.4~59.4%), and the highest total fertilization rate (mono- and polyspermic oocytes) was observed at $1{\mu}M$ DAVA (83%). In conclusion, addition of DAVA to fertilization medium improved sperm motility, and reduced ROS level so as to potentially improve sperm-oocyte binding in IVF, suggesting the potential of a compound isolated from mushrooms in assisted reproductive technology for humans and animals.

• Journal of Pharmaceutical Investigation
• /
• v.37 no.3
• /
• pp.149-158
• /
• 2007

To investigate the permeability of lidocaine, percutaneous absorption studies were performed using excised hairless mouse skin and the penetration of lidocaine via the skin was determined. To increase the skin permeation of lidocine, the effects of $Labrasol^{(R)}$, $Labrafil^{(R)}$, $Labrafac^{(R)}$ and $Transcutol^{(R)}$ were investigated. The skin permeation of lidocaine was increased when $Labrasol^{(R)}$ and $Transcutol^{(R)}$ were used as permeation enhancer. To evaluate the influence of ultrasound, various factors such as application modes (continuous mode and pulsed mode), frequency (1.0 and 3.0 MHz) and intensity (1.0, 1.5 and 2.0 w/$cm^2$) were investigated with lidocaine hydrogel. The pronounced effect of ultrasound on the skin permeation of lidocaine was observed at all ultrasound energy levels. The influence of frequency having an effect on skin permeation rate was higher in the case of using 1 MHz, 2.0 w/$cm^2$ and continuous treatment. As the intensity of ultrasound increased, the permeation of lidocaine was accelerated. The in vivo anesthetic effects were evaluated by two aspects as mechanical threshold and electrical threshold. Six healthy volunteers consented to the randomized, double-blind, and cross-over designed study in each group. In each subject, 3 groups were adapted such as K group (ultrasound with gel base only), L group (lidocaine gel) and B group (ultrasound with lidocaine gel). In conclusion, lidocaine was potent anesthetic which could be block pain threshold effectively. And ultrasound could accelerate the skin penetration of lidocaine. The phonophoretic delivery system could be a good candidate for lidocaine as a local anaesthetic to improve the skin permeation and in vivo anaesthetic effect.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.620-625
• /
• 2002

Considering the fuel consumption of car, a light structure of aluminum alloys is desired for car body nowadays. However, fusion welding of aluminum alloys has some problems of reduction of joint efficiency, porosity formation and hot cracking. ill the present work, investigation to improve the joint performance of laser welded joint has been carried out by addition of Cu, Ni, and Zr to A6N01 alloy welds. Aluminum alloy plate of 2.0mm in thickness with filler metal bar was welded by twin beam Nd:YAG laser facility (total power:5kW). The filler metals were prepared by changing the chemical compositions for adding the elements into the weld metal. Thirteen filler metal bars were prepared and pre-placed into the base metal before welding. Ar gas shielding with a flow rate of 10 l/min was used. The defocusing distance is kept at 0 mm. At travel speeds of 3 to 9 m/min and at laser power of 5kW (front beam 2kW rear beam 3kW), full penetration welds were obtained, whereas at travel speeds of 12 to 18 m/min and same power, partial penetration was observed. The joint efficiency of laser-welded joint was improved by the addition of Cu, Ni, and Zr due to the solid solution hardening, grain refining and precipitation hardening. The type of hardening has been further considered by metallurgical examination.

• Archives of Pharmacal Research
• /
• v.26 no.8
• /
• pp.644-648
• /
• 2003

To investigate the feasibility of developing a new ondansetron transdermal system, the effects of vehicles and penetration enhancers on the in vitro permeation of ondansetron hydrochloride (OS) from a pressure-sensitive adhesive (PSA) matrices across dorsal hairless mouse skin were studied. Vehicles employed in this study consisted of various ratios of propylene glycol monocaprylate (PGMC)-diethylene glycol monoethyl ether (DGME) co-solvents and PGMC-propylene glycol (PG) co-solvents with 3% oleic acid. $Duro-Tak^\circledR$ 87-2100 and $Duro-Tak^\circledR$ 87-2196 were used as PSAs. The concentration of DGME in PGMC-DGME co-solvent system affected the release rate; as the concentration of DGME increased, the release rate decreased. The cumulative release amount of OS increased as the ratio of PSA to drug solution decreased. The permeation flux was also primarily affected by the amount of PSAs; as the amount decreased, the permeation flux increased. The overall fluxes from matrix formulations were significantly lower when compared to those obtained from solution formulations. The ratio of PG to PGMC did not affect permeation flux, while the lag time decreased significantly from $5.14\pm3.31 to 0.31\pm0.12$ h as the PG increased from 40% to 60%.

• Nuclear Engineering and Technology
• /
• v.54 no.2
• /
• pp.674-680
• /
• 2022

In the present study, radiation shielding and protection ability of prepared Flyash-lime-Gypsum (FaLG) bricks has been studied in terms of energy exposure build up factors and dose parameters. The energy exposure build up factors of Flyash-lime-Gypsum (FaLG) bricks have been calculated for the energy range of 0.015 MeV-15 MeV and for penetration depth upto 40 mfp directly using a new and simplified Piecewise Linear Spline Interpolation Method (PLSIM). In this new method, the calculations of G.P fitting parameters are not required. The verification and accuracy of this new method has been checked by comparing the results of exposure build up factor for NBS concrete calculated using present method with the results obtained by using G.P fitting method. Further, the relative dose distribution and reduced exposure dose rate for various radioactive isotopes without any shielding material and with Flyash-lime-Gypsum (FaLG) bricks have been calculated in the energy range of 59.59-1332 keV. On the basis of the obtained results, it has been reported that the prepared Flyash-lime-Gypsum (FaLG) bricks possess satisfactory radiation shielding properties and can be used as environmentally safe storage facilities for low level nuclear waste.

• Reproductive and Developmental Biology
• /
• v.32 no.2
• /
• pp.97-104
• /
• 2008

Plasminogen activators (PAs) are serine protease that cleave plasminogen to form the active protease plasmin. PA/plasmin system playa role in mammalian fertilization and motility and acrosome reaction of sperm. The present study was undertaken to identify PAs in porcine gametes and investigate a possible role of plasminogen in in vitro fertilization in the pig. When boar spermatozoa were preincubated in a fertilization medium (mTBM) for 0, 2, 4 or 6 h, the activity of tPA-PAI ($110{\sim}117\;kDa$), tPA ($62{\sim}70\;kDa$), and uPA ($34{\sim}38\;kDa$) was observed in the sperm incubation medium and sperm sample. PA activities in the sperm incubation medium significantly (p<0.05) increased according to increasing incubation times, while PA activities in sperm significantly (p<0.05) decreased at the same times. In addition, the rate of acrosome reaction in spermatozoa increased by increasing culture times. When oocytes were separated from porcine cumulus-oocytes complexes at 0, 22 or 44 h of maturation culture, no PA activities were observed in cumulus free-oocyte just after aspiration from follicles. However, the activity of tPA-PAI ($108{\sim}113\;kDa$) and tPA ($75{\sim}83\;kDa$) was observed at 22 h of in vitro culture and significantly (p<0.05) increased as the duration of the culture increased. On the other hand, when porcine oocytes were activated by sperm penetration or calcium ionophore, plasminogen significantly (p<0.05) increased ZP dissolution time (sec) in activated oocytes by sperm penetration. These results suggest that supplementation of plasminogen to fertilization medium may playa positive role in the improvement of in vitro fertilization ability in the pig.

• International Journal of Korean Welding Society
• /
• v.2 no.2
• /
• pp.26-31
• /
• 2002

Considering the fuel consumption of car, a light structure of aluminum alloys is desired fer car body nowadays. However, fusion welding of aluminum alloys has some problems of reduction of joint efficiency, porosity formation and hot cracking. In the present work, investigation to improve the joint performance of laser welded joint has been carried out by addition of Cu, Ni, and Zr to A6NO 1 alloy welds. Aluminum alloy plate of 2.Omm in thickness with filler metal bar was welded by twin beam Nd: YAG laser facility (total power: 5kW). The filler metals were prepared by changing the chemical compositions for adding the elements into the weld metal. Thirteen filler metal bars were prepared and pre-placed into the base metal before welding. Ar gas shielding with a flow rate of 10 1/min was used. The defocusing distance is kept at 0 mm. At travel speeds off 3 to 9 and at laser power of 5kW (front beam 2kW rear beam 3kW), full penetration welds were obtained, whereas at travel speeds of 12 to 18 m/min and same power, partial penetration was observed. The joint efficiency of laser-welded joint was improved by the addition of Cu, Ni, and Zr due to the solid solution hardening, grain refining and precipitation hardening. The type of hardening has been further considered by metallurgical examination.

• Journal of Welding and Joining
• /
• v.30 no.6
• /
• pp.49-55
• /
• 2012

The tandem welding process is one of the most efficient welding processes widely used in material joining technique such as manufacturing of strong and durable structures. It facilitates high rate of joint filling with little increase in the overall rate of heat input due to the simultaneous deposition from two electrode wires. The two electrodes in tandem welding process helps in high-efficiency and high productive of welding process. In this study a automated tandem welding system is developed to determine the correlation between cathode and anode and compared with current ratio of the two electrode torch. Three different inter-electrode distances were chosen, 25mm, 35mm and 45mm to perform the experiment with three different current ratio. From the experiment results, the current ratio between two torch has a large impact on width, height and depth of penetration. In addition, a stable bead geometry is obtained when inter-electrode distance is 35mm.

• Journal of Welding and Joining
• /
• v.32 no.6
• /
• pp.22-28
• /
• 2014

Most publications on friction stir welding describe phenomena or results with given process parameters like feed rate, rotation speed, angle and depth of penetration. But without a complete documentation of tool design, the results under the same process parameters are completely different. For this purpose, the Institute of Cutting and Joining Manufacturing Processes (tff), University of Kassel investigated the influence of tool roughness on the friction stir welding process. Therefore a defined surface finish was produced by turning and die sinking. As basis of comparison the constant parameters were rotation speed, feed rate, tilt angle and a heel plunge depth. Sound butt-welds were produced in aluminium alloy 6082 (AlMgSi1) with 1.5 mm sheet thickness with a turned reference tool with a surface of $Ra=0.575{\mu}m$ in position controlled mode. The surfaces are manufactured from a very fine to a very rough structure, classified by the VDI-classes with differences in the arithmetical mean roughness. It can be demonstrated with the help of temperature measures, that less heat is generated at the surfaces of the shoulder and the pin by the higher roughness due to lower active friction contact surface. This can also be seen in the resulting wormhole defects.