• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.8
• /
• pp.661-666
• /
• 2003

Constant area expansion devices such as capillary tubes, short tube orifices are being gradually replaced with electronic expansion valves (EEVs) because of increasing focus on comfort and energy conservation. In this study, the performance of a water-to-water heat pump as a function of refrigerant charge is investigated in steady state, cooling mode operation with expansion devices of a capillary tube and an EEV. The performance of the capillary tube system varies drastically according to the change of refrigerant charge amount and inlet temperature of the secondary fluid in the condenser. Cooling capacity and COP of the EEV system show little dependence on the refrigerant charge, while those are strongly dependent on the secondary fluid temperature at the condenser inlet. In general, for a wide range of operating conditions the EEV system shows much higher performance as compared with the capillary tube system. The performance of the EEV system can be optimized by adjusting EEV opening to maintain a constant superheat at all test conditions.

• Archives of Pharmacal Research
• /
• v.12 no.2
• /
• pp.143-147
• /
• 1989

The urea effect on skin permeation of clonidine was investigated to reduce a log time and to increase a permeability. ICR mouse skin and human skin were used and were assumed to be a two-layer membrane consisted of stratum corneum and viable epidermis. The urea acted as a skin denaturant and humectant in the whole epidermis. Also it enhanced the skin permeability of clonidine about 3.5 times. On the other hand, it enhanced the skin permeability by acting as a humectant in the viable epidermis. But the urea effect on the whole epidermis was shown to be greater than that on the viable epidermis. Therefore, it was found that the effect of urea was greater on the stratum corneum than the viable epidermis. Variation of enhancing effect according to the concentration of urea was not found in the range of 1% to 20%.

• Near Infrared Analysis
• /
• v.2 no.1
• /
• pp.55-58
• /
• 2001

The object of this work was to investigate the influence of growing district and harvest year on calibration for sweetness (Brix) determination of Fuji apple fruit using near infrared (NIR) reflectance spectroscopy, and to develop the robust calibration across these variation. The calibration models was based on wavelength range of 1100∼2500 nm using a stepwise multiple linear regression. A calibration model by sample set of one growing district was not transferable to other growing districts. The combined calibration (data of three growing districts) predicted reasonable well against a population set drawn from all growing districts (SEP=0.69, Bias=0.075). A calibration model by sample set of one harvest year was not also transferable to other harvest years. The combined calibration (data of three harvest years) predicted well against a population set drawn from all harvest years (SEP=0.53, Bias=0.004).

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.4 no.2
• /
• pp.31-37
• /
• 1995

This study is focused on the prediction of appropriate tool life by clarifying the correlation between progressive tool wear and AE signal. when rcutting SM45C by End mill in machining center. First of all, end mill have a problem that position of sensor sticking because it is revolution tool, but I think that it can be bained specific character according to sticking Sensor in the Vise. Consequently, the following results have been obtained; 1. Each cutting speed of feed rate over 0.1mm had a tendency to increase linearly according to the RMSAE 2. The level of AE signal at the same cutting area was more sensitive to depth of cut tharn the variation of feed rate 3. In the range of cutting duringqr about 75minqr atqr cutting speed 27m/min flankqr wear turns up aboutqr 0.21mm, aboutqr 0.29mm in the caseqr of about 65minqr at 33/min, qr hereby RMSAE increased rapidly at 0.2mm flank wear, also AE-HIT and CUM-CNTS.

• Carbon letters
• /
• v.12 no.2
• /
• pp.102-106
• /
• 2011

Carbon nanotubes (CNTs) have been synthesized by ferrocene-catalyzed pyrolysis of toluene. The influences of the experimental conditions on the morphology and microstructure of the product have been analyzed. To find the proper temperature for synthesis of CNTs, the experiment was performed in a temperature range from 800 to $1100^{\circ}C$. From content variation of ferrocene and thiophene as the catalyst, morphological change of carbon nanotubes has been observed. Also, the influence of the gas ratio of hydrogen and argon on the nanotube samples was analyzed by scanning electron microscopy and transmission electron microscopy.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.6
• /
• pp.348-352
• /
• 2014

In light of the sure protection function, the most important factors of a varistor are the clamping voltage ratio and degradation characteristics. The degradation characteristics of Pr/Co/Cr/Er co-doped zinc oxide varistors were investigated by impulse currents (0.4~2.1 kA) stress for the specified content of $Er_2O_3$ (0.5 and 2.0 mol%). The varistor doped with 2.0 mol% $Er_2O_3$ exhibited the best clamp characteristics, with the clamp voltage ratio (K) in the range of K = 1.63~1.88 at the impulse currents of 5-50 A. However, the varistor doped with 0.5 mol% exhibited excellent electrical stability, with variation rates for the breakdown field, for the nonlinear coefficient, and for the leakage current density of -6.9%, -12.6%, and -14.3%, respectively, after application of an impulse current of 2.1 kA. In contrast, the varistor doped with 2.0 mol% was destroyed after application of an impulse current of 1.2 kA.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.9
• /
• pp.42-50
• /
• 2015

The Buck-Boost converter consisted of two switches is more expensive than the conventional Buck converter, because of the increase of the components. However, it can control the DC voltage depending on the requested load voltage without additional circuits, because it can control the voltage under the relatively wide range of the load. Additionally, it can control the output voltage constantly under the variation of the input voltage. In the paper two control loops consisted of current and voltage control are designed. When two controllers are operated at the same time the problem of the output voltage is occurred. Therefore, the solution of the output voltage problem is proposed. Finally, the validity of the proposed scheme is investigated with simulated and experimental results for a prototype system rated at 1kVA.

• Journal of Sensor Science and Technology
• /
• v.17 no.4
• /
• pp.273-280
• /
• 2008

Monolith aperture-type oxygen sensors with simple structure of YSZ(pin-hole)/Pt/ YSZ(solid electrolyte)/Pt were fabricated by co-firing technique. To enhance the yield of productivity, a couple of YSZ green sheets for diffused barrier and solid electrolyte were prepared by tape-casting and co-firing method. The limit current characteristics of the oxygen sensors were measured between 500 and $650^{\circ}C$ The heating temperature of $600^{\circ}C$ was optimum as a portable oxygen sensor in the range of oxygen concentration from 0 to 75 vol%. Linear proficiency of limit current behavior as a function of oxygen concentration was controlled by the variation of aperture dimension. The fabricated oxygen sensors showed the stable sensing output for 30 days. Gas leakage in bonding area due to warping, cracking and thermal cycling was not found in the period.

• Journal of the Korean Society of Industry Convergence
• /
• v.3 no.2
• /
• pp.123-130
• /
• 2000

Fuzzy control is proposed to regulate cutting force in turning operations under varying cutting conditions. The traditional linear controllers based on crisp mathematical model cannot effectively control cutting force becasue of the nonlinear dynamics of turning operations. The proposed fuzzy controller is based on operator experience and expert knowledge. The membership functions for the inputs and the output of the controller are designed. Cutting force is regulated by adjusting feedrate according to the variation of cutting conditions. The performance of the proposed controller is evaluated by experiments. The results of experiments show that the proposed fuzzy controller has a good cutting force regulation over a wide range of cutting conditions.

• Journal of the Korean Ceramic Society
• /
• v.29 no.1
• /
• pp.48-52
• /
• 1992

Indium tin oxide (ITO) layers are of considerable interest on account of the combination of properties they provide high electrical conductivity, high infrared reflection with high solar energy transmission, high transmission in the visible range. We are concerned about the variation of the spectral transmittances and sheet resistances as the thickness of SiO2-ZrO2 barrier layer and ITO layers and heat treating conditions are changed. Transmittances and reflectivities were studied by measuring UV-VIS-NIR-, FT-IR spectroscopy. ITO films are crack free, homogeneous and of polycrystalline cubic structure. The microstructure of good ITO films shows a narrow grain size distribution and mean value of 100 nm. The selectivity of absorbing properties is improved by increasing the thickness of ITO films. The increase of sheet resistance of ITO films are due to the increase in the reaction between films and glass substrate.