• Journal of Satellite, Information and Communications
• /
• v.11 no.4
• /
• pp.94-101
• /
• 2016

Satellite data for remote sensing technology has limitations, especially with visible range sensor, cloud and/or other environmental factors cause missing data. In this study, using land surface temperature data from the MODerate resolution Imaging Spectro-radiometer(MODIS), we developed retrieving methods for satellite missing data and developed three methods; mean bias, regression analysis and local variation method. These methods used the previous day data as reference data. In order to validate these methods, we selected a specific measurement ratio using artificial missing data from 2014 to 2015. The local variation method showed low accuracy with root mean square error(RMSE) more than 2 K in some cases, and the regression analysis method showed reliable results in most cases with small RMSE values, 1.13 K, approximately. RMSE with the mean bias method was similar to RMSE with the regression analysis method, 1.32 K, approximately.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.118-131
• /
• 1982

1. In order to investigate the effect of variation of assembly time on glue bond strength, and to determine the optimum range of assembly time with given glue, this experiment was made at the suggestion of the Wood Technology Laboratory, School of Forestry, Yale University. 2. For this investigation, three-ply-plywoods with 1/22 inch, birch veneer, phenolic resin, and soybean glue were made at the following variation of assembly time, that is, 1, 5, 10, 25, 35, 50, and 70 minutes, under both open and closed assembly manners, and the shear strength test at dry and wet were adoptted. 3. The shear strength and wood failure of each plywood panel constructed at the given assembly time have been illustrated in Tables 1, 2, 3 and 4. It has shown that there is a remarkable tendency, for increasing assembly time to give lower shear strength and wood failure throughout almost all cases. The effective range of assembly time of tested glues in this investigation for both open and closed assembly are summarized in the Table 7. Thus, allowable assembly time for Phenolic resin may be up to 10 minutes under open assembly and up to 50 minutes under closed assembly. For soybean glue, the permissible assembly time may be up to 5 minutes under open assembly and up to 15 minutes under closed assembly. The allowable assembly time for open assembly with the same glue is reduced by approximately one third or more than one third as compared with closed assembly time. This might mean that the closed asembly time for these glues is more practical than the open assembly.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.29 no.1
• /
• pp.33-42
• /
• 1999

Geometrically standardized dental radiographs were taken. We prepared Digital Cu-Equivalent Image Analyzing System for quantitative assessment of mandible bone. Images of radiographs were digitized by means of Quick scanner and personal Mcquintosh computer. NIH image as software was used for analyzing images. A stepwedge composed of 10 steps of 0.1mm copper foil in thickness was used for reference material. This study evaluated the effects of step numbers of copper wedge adopted for calculating equation. kVp and exposure time on the coefficient of determination(r²)of the equation for conversion to Cu-equivalent image and the coefficient of variation and Cu-Eq value(mm) measured at each copper step and alveolar bone of the mandible. The results were as follows: 1. The coefficients of determination(r²) of 10 conversion equations ranged from 0.9996 to 0.9973(mean=0.9988) under 70kVp and 0.16 sec. exposure. The equation showed the highest r was Y=4.75614612-0.06300524x +0.00032367x² -0.00000060x³. 2. The value of r² became lower when the equation was calculated from the copper stepwedge including 1.0mm step. In case of including 0mm step for calculation. the value of r showed variability. 3. The coefficient of variation showed 0.11, 0.20 respectively at each copper step of 0.2, 0.1mm in thickness. Those of the other steps to 0.9 mm ranged from 0.06 to 0.09 in mean value. 4. The mean Cu-Eq value of alveolar bone was 0.14±0.02mm under optimal exposure. The values were lower than the mean under the exposures over 0.20sec. in 60kVp and over 0.16sec. in 70kVp. 5. Under the exposure condition of 60kVp 0.16sec.. the coefficient of variation showed 0.03. 0.05 respectively at each copper-step of 0.3, 0.2mm in thickness. The value of r² showed over 0.9991 from both 9 and 10 steps of copper. The Cu-Eq value and the coefficient of variation was 0.14±0.01mm and 0.07 at alveolar bone respectively. In summary. A clinical application of this system seemed to be useful for assessment of quantitative assessment of alveolar provided high coefficient of determination is obtained by the modified adoption of copper step numbers and the low coefficient of variation for the range of Cu-Equivalent value of alveolar bone from optimal kVp and exposure time for each x-ray machine.

• Korean Journal of Optics and Photonics
• /
• v.17 no.6
• /
• pp.548-555
• /
• 2006

We investigate the effect of the reflectivity of both facets and the phase of a phase tuning section on the self-pulsation (SP) characteristics of multisection index-coupled (IC) DFB lasers composed of two index-coupled DFB sections and a phase tuning section between them in terms of yield. In the case of weak coupling strength, as the reflectivity of both facets increases, the effect of reflected fields from both facets and the other DFB section on the mode characteristics of one DFB section increases. Thus the number of mode hoping increases and yield decreases for the variation of phases of both facets. In the case of strong coupling strength, as the reflectivity of both facets increases, the spatial hole burning effect increases, so that the yield decreases. The maximum yield and the range of the phase of a phase tuning section with yield more than 40% decrease as the facet reflectivity increases irrespective of coupling strength. As the coupling strength increases, the variation of yield for the variation of the phase of a phase tuning section increases and the variation of the phase of a phase tuning section with the maximum yield for the variation of the reflectivity of both facets decreases. The yield characteristics of the cases with the coupling strengths of 2 and 3 are better than those with the coupling strengths of 1.2 and 4.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.2
• /
• pp.138-145
• /
• 2018

This paper studies the bending behavior of ultra-high-performance fiber-reinforced concrete (UHPFRC) beams focused on the effect of variation in major material design parameters such as tensile strength, elastic modulus of UHPFRC, and rebar ratio. Analytical results show that the variation in the range of ${\pm}20%$ in the tensile strength of UHPFRC causes the significant difference in ${\pm}8{\sim}9%$ of bending strength compared to the reference condition. The variation of elastic modulus in UHPFRC rarely causes the effect on the bending strength of the UHPFRC section, whereas causes the difference in the slopes of moment-curvature curves, indicating different bending stiffness of UHPFRC sections. For the rebar with yield strength of 400MPa, the bending strength of SC120f is increased by 30, 67, and 99% when the rebar ratio is 1.0, 1.5, and 20%, respectively, compared to the rebar ratio of 0.5%. Therefore, it is observed that the variation of rebar ratio significantly affects the difference in bending strength of UHPFRC beams. However, as the compressive strength of UHPFRC becomes greater, the effect of rebar ratio on the increase of bending strength is decreased.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.13 no.2 s.30
• /
• pp.155-165
• /
• 1989

The purpose of this study was to investigate on the sleeve form variation according to arm movements for elderly women. This study was experimented using the Plaster gypsum. The subjects who were elderly women were divided into three groups according to Rorher Index. Arm movements were five type ($0^{\circ},\;45^{\circ},\;90^{\circ},\;135^{\circ},\;180^{\circ}$) to each the vertical motion in front and in side. The statistical analyses used in this study were Mean, Standard Deviation, Spearman's correlation coefficients, paired T-test, Kruskal-wallis one-way ANOVA and Duncan's multiple range test. The results were as follows: 1) Increasing the movements, the width of the sleeve increased and the height of the sleeve cap decreased but girth of the sleeve cap was not consistant. 2) When varied the rates of the three aspects of the sleeve, the height of the sleeve cap showed the largest variation rate. 3) There was a negative correlation between the height and the width of the sleeve. On the other hand, there was a positive correlation between the sleeve width and the sleeve girth. 4) There were the vertical motion differences between in front and in side on the three aspects of sleeve. 5) The sleeve width and the sleeve girth were different according to somatotypes but the height of the sleeve cap was not different. 6) According to the variation rates of the body surfaces in length of standard lines, the form of sleeve was changed more in the front than in the back. Maximum variation rate showed in the areas of $D_1-D_3,\;E_1-E_3$ in the horizontal lines and $A-E_2$ in vertical lines. 7) According to the comparative drawing of the heights of sleeve cap and sleeve girth, the sleeve basic pattern $S_1(A.H/4)$ was more suitable for the direction $0^{\circ}\;and\;45^{\circ}$. And the basic pattern S_6(A.H/5)$ was more suitable for the direction $90^{\circ}$, the pattern $S_7(A.H/6)$ suitable for the direction $135^{\circ}$, and the pattern $S_8(A.H/8)$ was more suitable for the direction $180^{\circ}$.

• The Journal of the Korean Society for Microbiology
• /
• v.35 no.2
• /
• pp.97-108
• /
• 2000

Two-dimensional gel electrophoresis (2-DE) is an essential tool of proteomics to analyse the entire set of proteins of an organism and its variation between organisms. Helicobacter pylori was tried to identify differences between strains. As the first step, whole H. pylori was lysed using high concentration urea contained lysis buffer [9.5 M Urea, 4% CHAPS, 35 mM Tris, 65 mM DTT, 0.01% SDS and 0.5% Ampholite (Bio-Rad, pH 3-10)]. The extract ($10\;{\mu}g$) was rehydrated to commercially available immobilised pH gradient (IPG) strips, then the proteins were separated according to their charges as the first dimensional separation. The IPG strips were placed on Sodium Dodecyl Sulfate-Polyacrylamide Gel Electrophoresis (SDS-PAGE) to separate according to molecular mass of the proteins as the second dimension. The separated protein spots were visualised by silver staining in order to compare different expression of proteins between strains. Approximately 120 spots were identified in each mini-protein electrophoresised gel, furthermore about 65 to 75 spots were regarded as identical proteins in terms of pI value and molecular weight between strains used. In addition, distinct differences were found between strains, such as 219-1, Y7 and Y14, CH150. Two representative strains were examined using strips which had pH range from 4 to 7. This strips showed a number of isoforms which were considered large spots on pH range 3-10. Furthermore, the rest of spots on pH 4-7 IPG strips appeared very distinctive compared to broad range IPG strips. 2-DE seems to be an excellent tool for analysing and identifying variations between H. pylori strains.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.4
• /
• pp.65-73
• /
• 2003

This paper presents the implementation of an analog signal-processing ASIS to detect an angular velocity signal from a vibrator angular velocity detection sensor. The output of the sensor to be charge appeared as the variation of the capacitance value in the structure of the sensor was detected using charge amplifiers and a self oscillation circuit for driving the sensor was implemented with a sinusoidal self oscillation circuit using the resonance characteristics of the sensor. Specially an automatic gain control circuit was utilized to prevent the deterioration of self-oscillation characteristics due to the external elements such as the characteristic variation of the sensor process and the temperature variation. The angular velocity signal, amplitude-mod)Hated in the operation characteristics of the sensor, was demodulated using a synchronous detection circuit. A switching multiplication circuit was used in the synchronous detection circuit to prevent the magnitude variation of detected signal caused by the amplitude variation of the carrier signal. The ASIC was designed and implemented using 0.5${\mu}{\textrm}{m}$ CMOS process. The chip size was 1.2mm x 1mm. In the experiment under the supply voltage of 3V, the ASIC consumed the supply current of 3.6mA and noise spectrum density from dc to 50Hz was in the range of -95 dBrms/√Hz and -100 dBrms/√Hz when the ASIC, coupled with the sensor, was in normal operation.

• Korean Journal of Plant Taxonomy
• /
• v.43 no.3
• /
• pp.181-187
• /
• 2013

Genetic variation in Asaum misandrum, a woodland herb in Korea, was investigated based on allozyme analysis with starch gel electrophoresis. All of previously reported populations in Korea were sampled and seven loci from six enzymes were analyzed. Overall genetic variation of A. misandrum population showed considerably high levels of genetic variation within the species (A = 2.05, P = 71.4, $H_E$ = 0.294). A positive $F_{IS}$ value of A. misandrum indicated overall deficiency of heterozygotes, and a low $F_{ST}$ value (0.112) meant very little differentiation among populations. Factors contributing to the high levels of genetic diversity found within populations of A. misandrum include population maintenance via wide distribution range from Korea to Japan and primarily outcrossing breeding system. Although it showed moderate genetic diversity level, most habitats of the species were scattered and discontinuous. Besides, low numbers of individuals were found in the most habitats and individuals are collected frequently from the wild due to the unique shape of the flowers as well as the rarity of the species. Thus, there is a need to set up a reasonable conservation strategies including the maintenance mechanism of genetic diversity of A. misandrum.

• Journal of the Korean Institute of Gas
• /
• v.22 no.3
• /
• pp.84-90
• /
• 2018

We researched the way to minimize the damage when the chlorine-leak accident take place in a purification plant. Since the level of risk based on the Off-site Risk Assessment(ORA) is a combination of proportional to the number of residents in the damaged area and frequency of accidents, we suggested the adequate conditions to reduce the number of residents in the damaged area by means of the operating temperature of a handling facility, installation of a emergency shut-off valve, and the analysis of the variation of the damaging range in accordance with the type of enclosure. The coverage of damage was calculated by the 'KORA(Korea Off-site Risk Assessment Supporting Tool) program. The research shows that the lower operating temperature gets, the more emergency shut-off valve being installed and the higher enclosure level of facility becomes, the extent of damage gets decreased. The decreasing rate of worst case was 17.6%, 71%, 34.5% respectively, the decreasing rate of alternative case was 31.6%, 69.0%, 34.8% respectively.