• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.119-124
• /
• 2004

A new control method of spindle induction motor drive is proposed in this paper. In a conventional control method, the vector control was employed in the low speed range, while the constant V/f(volt-per-hertz) PWM control was employed in the high speed range. The two control modes were automatically selected at an intermediate speed. In a proposed control method, the direct vector-control with an encoder is employed in the low speed range(from 0 to 8,000rpm), and the vector control without an encoder is employed in th high speed(from 8,000 to 15,000rpm) by using flux observer and speed estimator. This paper describes problem of control method in a conventional spindle induction motor drive and proposes contort method as variation of motor speed.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.9
• /
• pp.105-114
• /
• 2004

Consolidation characteristics have been investigated by using Rowe cell consolidation tester for dredged soil, which is more than two times as much as the liquid limit. To examine the effects of variation of water content on consolidation characteristic, tests were carried out varying the initial water content from $100\%\;to\;150\%.$ The results were compared with the consolidation characteristics of remolded clay. The test results showed that the hither the initial water content of dredged clay was, the more noticeable the non-linear behavior of e-log P curves occurred. The variation of the gradient was apparent to load stage 40kPa and became less apparent after load stage 80kPa on the e-log P curves. Ratio of compression index stayed within the range suggested by Mesri and variation of initial water content has hardly influenced the coefficient of consolidation. On the contrary, it was found that the magnitude of consolidation load affects the vertical coefficient of consolidation. The variation of stratum thickness during consolidation processing needs to be taken into consideration since hydraulic fill would go through a much larger scale strain than land soil when it is subject to a load. In this study, the consolidation period considering the variation of stratum thickness was analyzed and the results were compared with those of existing consolidation studies which did not consider the variation of stratum thickness. According to the results of the study, the consolidation period of the ground with a larger strain was calculated more close to observed value in case of Mikasa theory which takes the variation of stratum thickness into consideration.

• Ocean and Polar Research
• /
• v.42 no.3
• /
• pp.233-247
• /
• 2020

This study was carried out at 5 sites 11 times over two years to identify the variation of benthic environments and benthic polychaetous community and analyze the benthic healthiness in Dangdong Bay, a small semi-enclosed inner bay of Jinhae Bay. The temperature of bottom water showed the typical temporal fluctuation of a temperate zone and was in the range of 5.94 ~ 23.94℃. The salinity did not change significantly during the study period and was in the range of 32.93 ~ 35.72 psu. The concentration of dissolved oxygen of bottom water fluctuated a great deal and was in the range of 0.31 ~ 10.20 mg/L. The lowest DO value was recorded in July 2015, as 0.31±0.04 mg/L corresponding to the hypoxic water mass. The hypoxic water mass was formed continuously at some sites also in July and August 2016. The mean grain size was in the range of 7.57 ~ 9.81Ø and the average was 8.89±0.20Ø. The surface sediments were mainly composed of fine sediment (mud) above 85%. The mean of TOC was 3.09±0.22% and LOI was 13.30±0.47%, showing very high levels in Korean coastal waters. The concentration of AVS was in the range of 0.33 ~ 1.28 mgS/g-dry. The high values of organic contents and AVS indicated that there had been the serious organic enrichment in Dangdong Bay. The number of species and the density of the benthic polychaetous community in Dangdong Bay were in the range of 2 ~ 38 species and 2 ~ 2,185 ind./㎡ during the study period. The number of species and density were highly sustained in winter and spring, and then decreased gradually with the formation of a hypoxic water mass in summer, and the lowest number of species and density were recorded in autumn. In September and November 2015, the dead zone expanded to almost the whole study area. Dominant polychaetous species were Capitella capitata, Lumbrineris longifolia, Paraprionospio patiens and Sigambra tentaculata, each known as opportunistic species and potential organic pollutant indicator species. In particular, Paraprionospio patiens showed a very high population density of 2,019 ind./㎡ in December 2016. Polychaetous communities at each sampling time were classified into 4 temporal groups according to dominant species in each period by cluster analysis and nMDS. 'Period Group AI' was formed in winter and spring of 2015, dominated by Capitella capitata, 'Period AII' in summer dominated by Lumbrineris longifolia, 'Period B' in autumn with no fauna in the dead zone, and particularly 'Period C' in winter of 2016 dominated by Paraprionospio patiens. As a result of analysis of benthic healthiness, the study area was estimated to be in a Fair~Very Poor condition by AMBI and in a Poor~Very Poor condition by BPI during the study period. Both AMBI and BPI showed that the study area was in a Very Poor condition in September and November 2015, and when the dead zone occurred. In Dongdong Bay, the fact that the formation of a hypoxic water mass occurred in summer and a dead zone in autumn were confirmed. In addition, the dominance of opportunistic and organic pollutant indicator species was also observed clearly. The benthic healthiness indexes such as AMBI and BPI showed that organic enrichment was serious in Dangdong Bay.

• Journal of Veterinary Clinics
• /
• v.39 no.3
• /
• pp.114-120
• /
• 2022

The purpose of this study is to examine the status of quality control using multipurpose phantom of ultrasound equipment used in hospital of veterinary college in South Korea by using ATS-539 multipurpose phantom so as to examine quantitative and objective new image evaluation method. Specialists discussed and analyzed multipurpose phantom images acquired by using convex transducer of 10 ultrasound imaging devices, currently used in 9 veterinary colleges, at 4.0-6.0 MHz. Total 8 items that can be measured with ATS-539 multipurpose phantom including dead zone, vertical and horizontal measurement, axial/lateral resolution, sensitivity, focal zone, functional resolution and gray scale/dynamic range were evaluated. For qualitative evaluation, valid decisions were made based on dead zone, axial/lateral resolution, and gray scale/dynamic range which are resolution index, and coefficient of variation (COV) and blind referenceless image spatial quality evaluator (BRISQUE) were found to increase objectivity. As a result of experiment, all the targeted ultrasonic devices were found appropriate from qualitative evaluation items of dead zone, axial/lateral resolution, and gray scale/dynamic range. In other evaluation items, they were found to be appropriate from focal zone and vertical measurement of quantitative evaluation while inappropriate from horizontal measurement, sensitivity, and functional resolution. COV value was 0.12 ± 0.04, and BRISQUE value was 47.77 ± 2.77, both analysis results show that the noise level of all ultrasonic devices was located within tolerance range. Upon image examination using ATS-539 multipurpose phantom, they were 100% appropriate with inspection standards of dead zone, axial/lateral resolution, and gray scale/dynamic range, and besides, focal zone and functional resolution can be used as evaluation items. In the field of veterinary medicine, 8 standard items using ATS-539 multipurpose phantom and image evaluation items using COV and BRISQUE can be used as standards for quality control of ultrasonography machine.

• Journal of Biosystems Engineering
• /
• v.8 no.1
• /
• pp.38-46
• /
• 1983

This study was carried out to investigate the possibility of improving the performance of a kerosene engine with water addition. The engine used in this study was a single-cylinder, four-cycle kerosene engine with the compression ratio of 4.5. Water could be successfully added into the inlet manifold by an extra carburetor for the volumetric ratios of 5, 10, 20, and 30 percents. Variable speed tests at wide-open throttle were performed for five speed levels in the range of 1,000 to 2,200rpm for each fuel type. Volumetric efficiency and brake specific fuel consumption were determined, and brake thermal efficiency based on the lower heats of combustion of kerosene was calculated. To examine variation in fuel consumption, CO concentration, and cooling water temperature, part load tests were also performed. The results obtained are summarized as follow. (1) Brake torque increased almost in proportion to volumetric efficiency. But the ratio of increase in torque was greater than that of volumetric efficiency. Mean torque over the speed range of 1,000 to 2,200rpm increased 1, 3, 7, and 2 percents for 5, 10, 20, and 30 percents water addition, respectively. The increase in brake torque with water addition was greater at lower speeds. (2) Mean brake specific fuel consumption over the speed range of 1,000 to 2,200rpm decreased 1, 2, 3, and 3 percents for 5, 10, 20, and 30 percents water addition, respectively. (3) Mean temperature of cooling water over the speed range of 1,000 to 2,200rpm decreased 2, 4, 8, and 12 percents for 5, 10, 20, and 30 percents water addition, respectively. (4) The effects of decreasing CO concentration in the exhaust emissions with water addition were significant. At the speed range of 1,000 to 2,200rpm, CO concentration in the exhaust emissions decreased 2, 10, 23, percents for 5, 10, and 20 percents water addition, respectively. (5) Deposits were not discovered in the combustion chamber during the experiment. However, a little rust was formed in the water-supply carburetor.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.777-788
• /
• 2014

This paper presents a wide output range, high power efficiency reconfigurable charge pump for driving touch panels with the high resistances. The charge pump is composed of 4-stages and its configuration automatically changes based on the required output voltage level. In order to keep the power efficiency over the wide output voltage range, internal blocks are automatically activated or deactivated by the clock driver in the reconfigurable charge pump minimizing the switching power loss due to the On and Off operations of MOSFET. In addition, the leakage current paths in each mode are blocked to compensate for the variation of power efficiency with respect to the wide output voltage range. This chip is fabricated using $0.18{\mu}m$ BCD process with high power MOSFET options, and the die area is $1870{\mu}m{\times}1430{\mu}m$. The power consumption of the charge pump itself is 79.13 mW when the output power is 415.45 mW at the high voltage mode, while it is 20.097 mW when the output power is 89.903 mW at the low voltage mode. The measured maximum power efficiency is 84.01 %, when the output voltage is from 7.43 V to 12.23 V.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.7
• /
• pp.572-577
• /
• 2001

The electrical properties of Pr$_{6}$ O$_{11}$ -based ZnO varistors consisting of ZnO-Pr$_{6}$ O$_{11}$ -CoO-Cr$_2$O$_3$-Er$_2$O$_3$ ceramics were investigated with sintering temperature in the range of 1325~f1345$^{\circ}C$. As sintering temperature is raised., the nonlinear exponent was increased up to 1335$^{\circ}C$, reaching a maximum 70.53, whereas raising sintering temperature further caused it to decrease, reaching a minimum 50.18 and the leakage current was in the range of 1.92~4.12 $\mu$A. The best electrical properties was obtained from the varistors sintered at 1335$^{\circ}C$, exhibiting a maximum (70.53) in the nonlinear exponent and a minimum (1.92 $\mu$A) in the leakage current, and a minimum (0.035) in the dissipation factor. On the other hand, the donor concentration was in the range of (0.90~1.14)x10$^{18}$ cm$^{-3}$ , the density of interface states was in the range of (2.69~3.60)x10$^{12}$ cm$^{-2}$ , and the barrier height was in the range of 0.77~1.21 eV with sintering temperature. With raising sintering temperature, the variation of C-V characteristic parameters exhibited a mountain type, reaching maximum at 134$0^{\circ}C$. Conclusively, it was found that the V-I, C-V, and dielectric characteristics of Pr$_{6}$ O$_{11}$ -based ZnO varistors are affected greatly by sintering temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.415-418
• /
• 2001

The I-V characteristics and its stability of ZPCCL-based ceramic varistors doped with La$_2$O$_3$in the range of 0.0~4.0 mol% were investigated. The density of ceramics was increased in the range of 4.7~5.8 g/cm$^3$ with increasing La$_2$O$_3$content. As La$_2$O$_3$content is increased, the varistor voltage was decreased in the range of 503.49-9.42 V/mm up to 2.0 mol%, whereas increasing La$_2$O$_3$content further caused it to increase. The ZPCCL-based varistors were characterized by nonlinearity, in which the nonlinear exponent is in the range of 3.05~82.43 and leakage current is in the range of 0.24-100.22 $\mu$A. Among ZPCCL-based varistors, 0.5 mol% added-varistors exhibited an excellent nonlinearity, in which the nonlinear exponent is 82.43 and the leakage current is 0.24 $\mu$A. Furthermore, they exhibited a high stability, in which the variation rate of the varistor voltage and the nonlinear exponent was -1.11% and -6.72%, respectively, under DC stress, such as (0.80 V$_{1mA}$9$0^{\circ}C$/12h)+(0.85 V$_{1mA}$115$^{\circ}C$//12h) +(0.90 V$_{1mA}$12$0^{\circ}C$//12h)+(0.95 V$_{1mA}$1$25^{\circ}C$//12h)+(0.95 V$_{1mA}$15$0^{\circ}C$//12h). Consequently, it was estimated that ZPCCL-based ceramics will be applied to development of Pr$_{6}$O$_{11}$ based ZnO varistors having a high performance.e.rformance.e.

• The Research Journal of the Costume Culture
• /
• v.31 no.3
• /
• pp.296-309
• /
• 2023

This study gathered basic information on the development of Jiu-Jitsu uniforms suitable for players in Korea. Detailed data were collected between December 20^th and December 30^th, 2022 on 21 selected brands sold in online shopping malls. For each, information was recorded on the production country, product type, price, colors, material, and sizing system. A total of 612 datasets were analyzed using frequency analysis, cross-tabulation, and Chi-square tests. Jiu-Jitsu uniforms were classified as either standard or limited edition. Limited edition uniforms were more expensive than regular uniforms. International brands had a higher price range than domestic brands. The most commonly used colors for Jiu-Jitsu uniforms were the regulation colors associated with the sport: white, black, and blue. Domestic brands were more likely to use non-regulation colors than international brands. The material used for the top half of the uniform was predominantly pearl weave, while the bottom half was usually ripstop. International brands used a more diverse range of materials than domestic brands. The Jiu-Jitsu uniform sizing system incorporated a range of sizes between A00 and A6. While sizing designations differed according to the established sizing systems of different countries, the sizes remained the same, as did the range of sizes available. Where size guides were provided, height and weight were used to help the customer determine the appropriate size. The dimensions of each size varied between brands. Overall, we found that international brands offer a more diverse range of Jiu-Jitsu uniform designs than domestic brands.

• The Journal of Korean Academy of Prosthodontics
• /
• v.29 no.2
• /
• pp.161-175
• /
• 1991

To understand the biomechanics of the mandibular movement of the patients with T.M.J. disorder, it is necessary to analyze the mandibular movement by the least moving points of instantaneous center of rotation on computer screen. In this study, two subjects without T.M.J. disorder and with normal occlusion and few patients with T.M.J. disorder were selected for obtaining the processing data. The habitual opening and dosing movements were recorded by image recognition system of video and computer and then the mandibular movement and the least moving point were analyzed using computer program for image anaysis of specialized points. The results obtained were as follows: 1. The least moving points of control group during opening and dosing were dose to the mandibular foramen, but in the test group there were differences between two positions of the least moving points during opening and closing. 2. The variations of the least moving point were in the range of $0.02\sim0.05cm$ of X-coordinate and $0.07\sim0.10cm$ of Y-coordinate for control group, whereas in the range of $0.05\sim0.30cm$ of X-coordinate and $0.08\sim1.65cm$ of Y-coordinate for test group. 3. The index of variation during opening and dosing movements was shown in $0.8\sim1.0$ for the control group and in $0.56\sim2.6$ for the test group. 4. After the treatment of the test group No. 4 by occlusal splint the least moving point was dose to the mandibular foramen and the index of variation was changed from 25 to 05. 5. The tracing shape of the least moving point in the test group represented the irregularities compared to the control group. 6. The mandibular opening and dosing movements were simulated on the computer screen following the movement of the least moving point of instantaneous center of rotation.