• Journal of the Korean Society of Safety
• /
• v.27 no.3
• /
• pp.9-14
• /
• 2012

The objectives of this study were to compare the results of HSL (Health and Safety Laboratory) ramp test with perceived sense of slip onto the several different floor surfaces under contaminated conditions. There are a variety of approaches from biomechanical measurements to psychophysical test and human perception. However, controversies over these approaches still remain. Some widely accepted methods need to be improved. AHP (Analytic Hierarchy Process) was used to evaluate the perception of slipperiness of seven different floor surfaces under the contaminated condition with glycerol solution. Twelve subjects worn same footwear and walked with self-selected step and cadence along the test floors. The angle of inclination obtained for water wet condition using 5 l/min with HSL ramp test was compared to perception of slipperiness. The surface roughness ($R_z$) related very well both AHP (r=0.95) and ramp test (r=0.92). The high significant correlation (r=0.90) was found between AHP and HSL ramp test.The HSL ramp test values (Coefficient of Friction, COF) according to subjective evaluation were divided into two categories. There were high correlations between test results (subjective evaluation, HSL ramp test) and surface roughness in Rz. Perception rating obtained with AHP showed a high correlation with COF obtained with HSL ramp test.

• Proceedings of the ESK Conference
• /
• 1996.10a
• /
• pp.33-40
• /
• 1996

본 연구의 목적은 작업생리학적 접근방법(physiological approach)을 이용하여 생리학적 작업 능력(PWC; physiological work capacity)을 추정할 경우 작업형태와 작업방법에 따른 차이점을 비교분석해 보고자 함이다. 작업유형으로는 자전거 에르고미터(cycle ergometer)와 트레드밀 (treadmill)을 사용하였고, 작업방법으로는 각각의 작업유형에 대하여 램프 테스트(ramp test 와 인크리멘탈 테스트(increemntal test)의 차이점을 비교하였다. 또한 외국인들의 생리학적 작업능력(PWC)과 한국인들의 생리학적 작업능력(PWC)을 비교,검토하여 NIOSH(National Institute of Safety and Healty)기준치를 사용하는데 문제점이 없는가를 검토해 보고자 하였다. 작업방법 에 따른 차이점은 자전거 에르고미터의 경우 램프 테스트(ramp test )253.63 ml/min로서 인크리 멘탈 테스트(increemental test) 2859.74ml/min 의 87.70 % 정도로 나타났으며, 트레드 밑의 경우 ramp test 2859.22ml/min로서 incremental test 289.46ml/min의 98.77%정도로 나타났다. 작업유형 에 따른 결과는 자전거 에르고미터의 ramp test 트레드밀의 ramp test 는 ramp test는 트레드밀의 ramp test의 88.72% 정도로 나타났으며, 자전거 에르고미터의 incremental tests는 트레이드밀 작 업의 98.% 정도로 나타났다.

• Journal of the Ergonomics Society of Korea
• /
• v.15 no.2
• /
• pp.89-98
• /
• 1996

The objective of this study was to make comparison of the physical work capacities with different types and methods of tasks. To produce standard work loads, a bicycle ergometer and a treadmill were used for the purpose of two different types of tasks. Maximal oxygen uptake measurement tests are usually performen (1) continuously - with no rest between work load increments, or (2) discontinuously - with the subjects resting several minutes between work periods. Continuous test protocol with two different methods of work load increments, (1) ramp test- with 3 to 5 minutes of work period for each work load, and (2) incremental test - where exercise intensity was increased progressively in 2 minutes interval, were used. Predicted physicala work capacities (PWCs) were compared with the one by Kim(1990), and Lee(1995), and the NIOSH physiological criteria. For ergometer test, the PWC based on the ramp test was 89.65% of the one based on the incremental test. The PWC values were 2553.88 ml/min for the ramp test and 2848.82 ml/min for the incremental test. For treadmill test, the PWC based on the ramp test was 97.54% of the one based on the incremental test. The PWC values were 2786.89 ml/min for the ramp test and 2857.24 ml/min for the incremental test. The PWC obtained with a bicycle ergometer was 91.64% of the one obtained with a treadmill for the ramp test, and 99.71% for the incremental test.

• Nuclear Engineering and Technology
• /
• v.41 no.2
• /
• pp.187-198
• /
• 2009

In this paper, three power ramp tests performed on high burn-up Re-crystallized Zircaloy2 - UO2 BWR fuel rods (56 to 63 MWd/kgU) within the SCIP project are simulated with METEOR and ALCYONE 3D. Two of the ramp tests are of staircase type up to Linear Heat Rates of 420 and 520 W/cm and with long holding periods. Failure of the 420 W/cm fuel rod was observed after 40 minutes. The third ramp test consisted of a more standard ramp test with a constant power rate of 80 W/cm/min up to 410 W/cm with a short holding time. The tests were first simulated with the METEOR 1D fuel rod code, which gave accurate results in terms of profilometry and fission gas releases. The behaviour of a fuel pellet fragment and of the cladding piece on top of it was then investigated with ALCYONE 3D. The size and the main characteristics of the ridges after base irradiation and power ramp testing were recovered. Finally, the failure criteria validated for PWR conditions and fuel rods with low-to-medium burn-ups were used to analyze the failure probability of the KKL rodlets during ramp testing.

• International Journal of Reliability and Applications
• /
• v.17 no.1
• /
• pp.85-105
• /
• 2016

In this paper accelerated life testing is incorporated in quality control technique of acceptance sampling plan to induce early failures in high reliability products.Stress under accelerated condition can be applied in constant-stress, step-stress and progressive-stress or combination of such loadings. A ramp-stress results when stress is increased linearly (from zero) with time. In this paper optimum failure-censored ramp-stress accelerated life test sampling plan for log-logistic distribution has been formulated with cost considerations. The log-logistic distribution has been found appropriate for insulating materials. The optimal plans consist in finding optimum sample size, sample proportion allocated to each stress, and stress rate factor such that producer's and consumer's interests are safeguarded. Variance optimality criterion is used when expected cost per lot is not taken into consideration, and bilevel programming approach is used in cost optimization problems. The methods developed have been illustrated using some numerical examples, and sensitivity analyses carried out in the context of ramp-stress ALTSP based on variable SSP for proportion nonconforming.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.649-656
• /
• 2004

Hypersonic wind tunnel test of the rectangular variable geometry intake is performed. For realization of a Precooled turbojet engine, development of a hypersonic ramjet engine is planned. To investigate performance of the intake of the hypersonic ramjet engine, wind tunnel test is done with freestream Mach number of 5.1. The total pressure recovery was 18 % with 12.9 % of ramp bleed. Several reasons for low total pressure recovery are shown. Supersonic internal compression is not enough. Then, the throat Mach number is high (M2.61) and total pressure losses at the terminal shock is large. Supersonic flow at the throat and position of the terminal shock is sensitive to a difference of the second ramp's throat height and the third ramp's throat height. Flow separations at the second ramp's trailing edge and the third ramp's leading edge are seen those could result in the trigger of unstart. The seal mechanism between the ramps and the sidewalls is important.

• Journal of Positioning, Navigation, and Timing
• /
• v.4 no.4
• /
• pp.195-203
• /
• 2015

In this study, the carrier acceleration-ramp-step test was applied to GPS carrier phase measurements, and the results were compared and analyzed. In the carrier acceleration-ramp-step test, the acceleration, ramp, and measurements are estimated using 10 consecutive carrier phase measurements for satellites observed at the same time based on the least square method. As for the characteristic of this test, if failure occurs in the measurement, the value jumps significantly compared to the previous result; but it judges that failure has occurred in all the satellites although failure has occurred in one satellite. Therefore, in this study, a method that eliminates a satellite with failure was suggested, and thresholds of the carrier acceleration, ramp, and step were suggested. The evaluation of the failure detection performance of carrier phase measurement using the suggested thresholds showed that failure could be detected when the carrier phase measurement changed abruptly by more than about 0.1 cycles.

• Transactions of the Society of Information Storage Systems
• /
• v.5 no.2
• /
• pp.70-75
• /
• 2009

Most hard disk drives uses load/unload technology because of benefits as like an increased areal density, a reduced power consumption and an improved shock resistance. However, ramp tilt induced by ramp manufacture and assembly causes mechanical problems such as unload fail in case of exceeding ramp tolerance. In this paper, we focus on experimental analysis for unloading characteristics affected by ramp tilt. We repeatedly perform load/unload test as 500,000 cycles for original model and ramp tilt model. This paper shows that it is possible to analyze unload characteristics through measuring scratch and wear of suspension lift-tab, ramp, suspension dimple-flexure and disk. We also identify structural relation between suspension lift-tab and ramp through scratch and wear of suspension lift-tab and ramp. As the result of measurement and analysis, we can investigate decrease of unloading performance in ramp tilt model.

• Journal of Korean Society for Quality Management
• /
• v.32 no.4
• /
• pp.208-219
• /
• 2004

This paper considers a nonparametric estimation of lifetime distribution for ramp stress tests with stress bound under intermittent inspection. The test items are inspected only at specified time points an⊂1 so the collected observations are grouped data. Under the cumulative exposure model, two nonparametric estimation methods of estimating the lifetime distribution at use condition stress are proposed for the situation which the time transformation function relating stress to lifetime is a type of the inverse power law. Each of items is initially put on test under ramp stress and then survivors are put on test under constant stress, where all failures in the Inspection interval are assumed to occur at the midi)oint or the endpoint of that interval. Two proposed estimators of quantile from grouped data consisting of the number of items failed in each inspection interval are numerically compared with the maximum likelihood estimator(MLE) based on Weibull distribution.

• International Journal of Reliability and Applications
• /
• v.15 no.2
• /
• pp.125-150
• /
• 2014

Accelerated life tests (ALTs) are extensively used to determine the reliability of a product in a short period of time. Test units are subject to elevated stresses which yield quick failures. ALT can be carried out using constant-stress, step-stress, progressive-stress, cyclic-stress or random-stress loading and their various combinations. An ALT with linearly increasing stress is ramp-stress test. Much of the previous work on planning ALTs has focused on constant-stress, step-stress, ramp-stress schemes and their various combinations where the stress is generally increased. This paper presents an optimal design of ramp soak-stress ALT model which is based on the principle of Thermal cycling. Thermal cycling involves applying high and low temperatures repeatedly over time. The optimal plan consists in finding out relevant experimental variables, namely, stress rates and stress rate change points, by minimizing variance of reliability function with pre-specified mission time under normal operating conditions. The Burr type XII life distribution and time-censored data have been used for the purpose. Burr type XII life distribution has been found appropriate for accelerated life testing experiments. The method developed has been explained using a numerical example and sensitivity analysis carried out.