• Journal of Advanced Navigation Technology
• /
• v.20 no.3
• /
• pp.232-237
• /
• 2016

As a possible standardization of wireless local area network (WLAN), IEEE 802.11 LRLP is under discussion in order to support long range and low power (LRLP) communication for internet of things (IoT) including drones and many other IoT devices. In this paper, an efficient adaptive resource unit allocation scheme for uplink multiuser transmission in IEEE 802.11 LRLP networks is proposed. In the proposed scheme, which adopts OFDMA random access based transmission scheme of IEEE 802.11ax, in order to enhance the efficiency of the slotted OFDMA random access, access point (AP) traces the history of the sizes of successfully transmitted uplink data, and adjusts the sizes of resource units for the next uplink multiuser transmission adaptively. Our simulation results corroborate that the proposed scheme significantly improves the system throughput.

• The Journal of the Korea Contents Association
• /
• v.17 no.1
• /
• pp.50-57
• /
• 2017

This study investigated the causes and problems of train operation impediments through the statistics analysis of 8 years'internal data of Daejeon Metropolitan Express Transit. By evaluating the risks regarding the system, equipment, and parts of high risk group, this study measured the Risk Index Severity, and applied the $5{\times}5$ Risk Assessment Matrix which is a method of risk management to calculate the scale of risk to analyze the safety level and allowance range. As a result, the car sector, the most serious risk, followed by machinery and equipment sector showed that the inherent risk. In particular, the door broken and the door rail signaling and control devices due to defects of the vehicle is high, but also the severity, and frequency are showing very frequent additional potential accidents. PSD also had defects in the machinery sector appeared to be the most dangerous of the PSD poor safety gates, it was found that the glass also involve the risk of mishandling and breakage of the PSD. This study intended to contribute to the transportation benefits through the safety and stable operation of Metropolitan Express Transit.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.115-121
• /
• 2017

The efficiency of railway track cleaning vehicle for eliminating fine particulate matter (PM10 and PM2.5) in a subway tunnel depends strongly on the structure of the air blowing and suction system installed under the train. To increase the efficiency of underbody suction system, this paper proposes a novel method to use the Coanda effect for the air blower and dust suction module. In particular, through Computational Fluid Dynamics (CFD) analysis, the flow control device induced by the Coanda effect enables an increase in the overall flow velocity and to stabilize the flow distribution of the suction module at a control angle of $90^{\circ}$. In addition, the flow velocity drop at the edge of the air knife-type blower can be improved by placing small inserts at the edge of the blower. Those 4 modular designs of the dust suction system can help remove the dust accumulated on the track and tunnel by optimizing the blowing and suction flows.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.202-207
• /
• 2016

An auxiliary real-time train communications system among drivers, train-traffic controllers and field workers is necessary to share hazard information (i.e. rockfall detection, track maintenance) in low visibility zones (long tunnels and steep curved track). To develop the appropriate communication system, this paper proposes a new way of power line communication using the rail track (Rail - PLC), which has little noise and distortion of attenuation. Therefore, it is important to measure the impedance of the rail and to apply an impedance matching technique to increase the transmission characteristic of the Rail - PLC. This study would evaluate the reflection and the transmission characteristics of the rail using a network analyzer and an impedance matching transformer. The suitable impedance matching ratio was 1:3.28 from the result of back-to-back testing. The results confirmed that the transformer can improve the performance of the transmission signal in Rail - PLC using an impedance matching technique.

• Journal of the Korean Society for Railway
• /
• v.17 no.1
• /
• pp.7-13
• /
• 2014

Stiffness variations and wave propagation/reflection in railway catenaries are the primary sources of contact loss between a pantograph and a railway contact wire. This paper analyzes which design parameter is more important for 200km/h conventional rail and 300km/h high-speed rail, in order to effectively reduce the contact loss. For the high-speed rail, the wave propagation and reflection in the overhead contact lines are more influential than the stiffness variation over a span. When the high-speed rail needs to speed-up, it is necessary to develop higher strength contact wires in order to increase the wave propagation speed. In addition, the dropper clamp mass should be reduced in order to alleviate the wave reflection. However, it is noted that the increase in the tension to a messenger wire could deteriorate the current collection quality, which contrasts with expectations. For the 200km/h conventional rail, the stiffness variation over a span is more influential than the wave propagation and reflection. Therefore, shortening span length, increasing the tension in the contact wire and optimizing the location of the droppers are recommended for a smoother stiffness variation over the span.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.1
• /
• pp.166-175
• /
• 2017

Hazardous volcanic activity will continue to occur in the ring of fire, a major area in the basin of the Pacific Ocean where a large number of earthquakes and volcanic eruptions occur. and, because of rising populations, development pressures, and expanding national and international air traffic over volcanic regions, risks to life and property through exposure to volcano hazards continue to increase. During an eruption, volcanic contamination can reach and exceed the cruising altitudes of turbine-powered aircraft, among others, within minutes and spread over vast geographical areas within a few days. Volcanic ash can affect the operation of aircraft at aerodromes. Volcanic ash deposition at an aerodrome, even in very small amounts, can result in the closure of the aerodrome until all the deposited ash has been removed. In this study, air traffic information framework is presented along with algorithms to define affected routes, waypoints and airports using GIS geometry analysis.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.2223-2231
• /
• 2010

Recently, an important physical device of transportation, such as car, railroad, ship and aircraft has changed into electronic control unit. According to accident reports, the most of car accidents are caused by faults of embedded software loaded to computer control unit. The facts implies that the test to find defects in embedded software haven't performed sufficiently. As a result, it is necessary to establish the test procedures of embedded software based on safety assessment criteria. The objective of this proposal is to provide a unit test procedure complied with the safety assessment criteria for the embedded software. In addition, an effective unit testing procedure and defect analysis methods are proposed and a testing procedure using a safety criteria built-in tool is presented.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1541-1550
• /
• 2007

A subway is one of many public transportation means that contributes toward our society including seoul and offering of its service and expression of various information are in need due to users high demand. And there are various class of users. For that reason an optical communication network in the general contorl center and station buildings was installed. Considering the importance of safe operation of subway, optical communication exists to enhance customer satisfaction. Safe operation is essential as its level of reliance accounts for about 95%. this paper will look for ways to promote mutual information interchange and operation know-how with systems of the same kind and sharing a capable of effective operation of systems in place. Optical communication network in the metropolis railroad accepts various kinds of control networks and data networks for train operation. As occasion demands, this paper presents effective application scheme and specialized organization about an optical communication operating system.

• The Korean Journal of Applied Statistics
• /
• v.26 no.4
• /
• pp.623-634
• /
• 2013

In this study, we provide empirical evidence of whether a spatial correlation among mode choices at the TAZ(Traffic Analysis Zone) level exists based on transit smart card data observed in Seoul, Korea. The results show that the areas with a higher probability that passengers choose to take a bus are clustered and that those regions have fewer metro stations than bus stations. We also found that the spatial correlation turned out to be statistically meaningful and provided an opportunity for the potential use of the spatial correlation in modeling mode choices. A reliable spatial interaction would constitute valuable information for transportation agencies in terms of their route planning and scheduling based on the transit smart card data.

• Journal of the Korea Concrete Institute
• /
• v.27 no.6
• /
• pp.669-676
• /
• 2015

Time dependent model for prediction of compressive strength development of concrete cured by microwave heating form was presented in this study. The presented model is similar to the equation which is given in ACI 209R-92 but the constants which is dependent on cement type and curing method in the presented model are modified by the regression analysis of the experimental data. Laboratory scale concrete specimens were cast and cured by the microwave heating form and drilled cores extracted from the specimens were fractured in compression. The measured core strengths are converted to standard core and in-situ strengths. These in-situ strengths are used for the regression.