• 한국산업융합학회 논문집
• /
• 제17권4호
• /
• pp.234-244
• /
• 2014

Recently it has been focused that the automobile engine has developed in a strong upward tendency for the use of the high viscosity and poorer quality fuels in achieving the high performance, fuel economy, and emission reduction. Therefore it is not easy to solve the problems between low specific fuel consumption and exhaust emission control at motor cars. In this study, it is designed and used the engine test bed which is installed with turbocharger and intercooler. In addition to equipped using CRDI by controlling injection timing with mapping modulator, it has been tested and analyzed the engine performance, combustion characteristics, and exhaust emission as operating parameters, and they were engine speeds(rpm), injection timing(bTDC), and engine load(%). From the result of an experimental analysis, peak cylinder pressure and the rate of pressure rise were increased, and the location of it was closer toward top dead center according to the increasing of engine speed and load, and with advancing injection timing. The combustion characteristics are effected by fuel injection timing due to be enhanced the mass burned fraction. Using the engine dynamometer for analyzing the engine performance, the engine torque and power have been enhanced according to advancing the fuel injection timing. In analyzing of exhaust emission, there has been a trade-off between PM and NOx with increasing of engine speed and load, and with advanced injection timing. The experimental data are shown that the formation of NOx has increased and PM, vice versa.

• 한국분무공학회지
• /
• 제25권1호
• /
• pp.21-26
• /
• 2020

The objective of this work is to numerically reveal the effect of equivalence ratio change on the simultaneous reduction of NO_X and soot emissions from the simulated-EGR compression ignition engine containing CO₂. An experiment was conducted by using a single-cylinder common-rail injection system engine, an intake control system, and exhaust emissions analyzers. The numerical analysis results were validated under the same experimental conditions. To investigate the effect of equivalence ratio by simulated-EGR containing CO₂, the O₂, N₂, and CO₂ mole fraction were changed in the initial air conditions to the cylinder. The results were analyzed in terms of peak cylinder pressure, indicated mean effective pressure, indicated specific nitrogen oxide, and indicated specific soot. It was revealed that ignition delay characteristics and heat release rate (ROHR) characteristics were not significantly different according to the equivalence ratio. However, as the equivalence ratio increased from 0.68 to 0.83, the maximum combustion pressure and IMEP decreased by about 6.5% and 9.4%, respectively. In the case of ISFC, as is well known, the trend is opposite of IMEP. In the case of ISNO, as the equivalence ratio increased, less NO was generated, and as the equivalence ratio increased by 0.05, the ISSoot value of about 10% increased.

• 한국소음진동공학회논문집
• /
• 제22권10호
• /
• pp.985-993
• /
• 2012

In this paper, a new method is proposed to estimate the sound pressure generated from gasoline direct injection (GDI) engine. There are many noise sources as much as components in GDI engine. Among these components, fuel pump, fuel injector, fuel rail, pressure pump and intake/exhaust manifolds are major components generated from top of the engine. In order to estimate the contribution of these components to engine noise, the total sound pressure at the front of the engine is estimated by using airborne source quantification (ASQ) method. Airborne source quantification method requires the acoustic source volume velocity of each component. The volume velocity has been calculated by using the inverse method. The inverse method requires many tests and has ill-condition problem. This paper suggested a method to obtain volume velocity directly based on the direct measurement of sound intensity and particle velocity. The method is validated by using two known monopole sources installed at the anechoic chamber. Finally the proposed method is applied to the identification and contribution of noise sources caused by the GDI components of the test engine.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.416-421
• /
• 2008

최근 세계 각국의 고속열차들은 속도 향상 측면에서 비약적인 발전을 보이고 있으며, 국내에서도 2007년부터 '차세대 고속철도 기술개발 사업'을 통해 최고속도 400km/h급의 고속열차 개발을 진행 중에 있다. 고속열차의 주행속도가 증가함에 따라 이전에는 제기되지 않았던 공기저항, 공력소음 문제, 열차의 교행 및 측풍에 의해 발생하는 압력변동, 터널출구에서 발생하는 미기압파 등의 문제들이 대두되고 있으며 이와 같은 문제들은 열차의 고속화를 제약하는 요인이 된다. 특히, 고속열차의 전두부 형상은 이러한 공기역학적 문제들과 밀접하게 연결되어 있으며, 팬터그래프의 소음 및 안정적인 집전 성능 확보 등도 속도 향상을 위해 반드시 고려해야하는 사항이다. 본 논문에서는 고속열차의 속도향상 노력의 일환으로 진행되고 있는 '공력해석 향상 기술'의 연구 내용과 더불어, 터널 미기압파 저감을 위한 전두부 형상 최적화 결과와 팬터그래프 공력성능 향상을 위한 강건 최적화 결과를 소개한다.

• Geomechanics and Engineering
• /
• 제28권3호
• /
• pp.265-281
• /
• 2022

A set of slurry shield test system capable of cutter cutting and slurry automatic circulation is used to investigate the deformation characteristics, the evolution characteristics of support resistance and the distribution and evolution process of earth pressure during excavating and collapsing of slurry shield tunneling in circular-gravel layer. The influence of cover-span ratio on surface subsidence, support resistance and failure mode of excavation face is also discussed. Three-dimensional numerical calculations are performed to verify the reliability of the test results. The results show that, with the decrease of the supporting force of the excavation face, the surface subsidence goes through four stages: insensitivity, slow growth, rapid growth and stability. The influence of shield excavation on the axial earth pressure of the front soil is greater than that of the vertical earth pressure. When the support resistance of the excavation face decreases to the critical value, the soil in front of the excavation face collapses. The shape of the collapse is similar to that of a bucket. The ultimate support resistance increase with the increase of the cover-span ratio, however, the angle between the bottom of the collapsed body and the direction of the tunnel excavation axis when the excavation face is damaged increase first and then becomes stable. The surface settlement value and the range of settlement trough decrease with the increase of cover-span ratio. The numerical results are basically consistent with the model test results.

• 대한토목학회논문집
• /
• 제30권6A호
• /
• pp.525-534
• /
• 2010

도로 경계석은 보도와 차도의 경계부에 설치하는 구조물로서 노면배수, 시선유도 등의 목적으로 사용된다. 현재 일반적인 경계석의 시공법은 경계석 기초 콘크리트를 타설한 후 콘크리트가 경계석을 지지할 수 있는 강도에 도달할 때까지 기다렸다가 경계석을 거치하고 측구 및 후면 보강콘크리트를 타설하는 공법을 사용하고 있다. 이러한 공법은 콘크리트의 분할 타설에 따른 콘크리트의 다짐 불량 및 부착강도 저하로 경계석이 차량충돌이나 토압 등에 의해 쉽게 분리되어 유지보수 비용발생과 미관을 저해하고 있다. 이러한 재래식 공법을 개선하고자 경계석과 측구를 동시에 시공할 수 있는 거푸집 레일과 지그를 이용한 일체형 시공법을 제안하였으며, 구조적 성능을 평가하기 위하여 횡 방향 재하시험, 인발 시험, 휨 시험과 같은 정적 시험을 실시하였고, 펜들럼 시험 및 실물차량 충돌 시험과 같은 동적 시험을 통한 성능평가를 실시하였다. 검토 결과 거푸집 레일과 지그를 이용한 일체형 시공법은 재래식 공법에 비해 콘크리트의 시공품질이 개선되고 부착강도가 증가하여 모든 시험에서 우수한 것으로 나타났다.

• 한국산학기술학회논문지
• /
• 제19권5호
• /
• pp.626-631
• /
• 2018

비상 피난 지원 시스템은 화재시 차연막이 형성되며 차연막 내에 가압을 하여 안전한 피난로를 확보해주는 시스템이다. 안정적인 작동을 위해서는 비상 피난지원 시스템의 차연막은 적절한 내화성능을 갖추어야 한다. 따라서 본 연구에서는 화재가 차연막에 미치는 영향을 수치해석적 방법으로 분석하였다. 수치해석 대상은 다중이용 건축물의 대공간 의류 상점의 화재로 가정 하였으며 상점의 가연물에 따라 화재 시나리오를 설정하였다. 차연막의 내화 안전 온도는 화재에 의해 발생하는 고온의 가스 온도가 $200^{\circ}C$ 이하 일때로 가정 하였다. 그 결과 Ceiling jet 의 영향으로 천장 부분에서 가장 높은 온도가 나타났으며 차연막의 내화 안전성은 열 방출률에 따라 화재로부터 차연막의 거리가 20 m부터 또한 최대 열방출율시 30 m 이후에 확보 할 수 있을 것으로 판단하였다. 또한 비상 피난지원 시스템 내부로 연기 유입을 차단하기 위해 차연막 내부를 양압으로 유지 하여야 하며 약 5 Pa 이상 가압이 필요 할 것으로 판단하였다. 따라서 향후 비상 피난 지원 시스템의 설계시 본 연구의 결과가 유용하게 사용 될 수 있을 것으로 판단된다.

• 대한기계학회논문집B
• /
• 제30권7호
• /
• pp.682-691
• /
• 2006

This study was conducted to assess the effect of mixed fuel composition and mass fraction on spray inner structure in evaporating transient spray under the various ambient conditions. Spray structure and spatial distribution of liquid phase concentration are investigated using a thin laser sheet illumination technique on the multi-component mixed fuels. A pulsed Ar+ laser was used as a light source. The experiments were conducted in a constant volume vessel with optical access. Fuel was injected into the vessel with electronically controlled common rail injector. Used fuel contain $i-octane(C_8H_{18}),\;n-dodecane(C_{12}H_{26})$ and $n-hexadecane(C_{16}H_{34})$ that are selected as low-, middle- and high-boiling point fuel, respectively. Experimental conditions are 25Mpa, 42MPa, 72MPa and 112MPa in injection pressure, $5kg/m^3,\;15kg/m^3\;and\;20kg/m^3$ in ambient gas density, 400K, 500K, 600K and 700K in ambient gas temperature, 300K and 368K in fuel temperature, and different fuel mass fraction. Experimental results indicate that the more high-boiling point component, the longer the liquid phase it were closely related to fuel physical properties, but injection pressure had no effect on. And there was a high correlation between the liquid phase length and boiling temperature at 75% distillation point.

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.45-51
• /
• 2012

This work was investigated 2-stage injection strategy on combustion and emissions in a direct injection compression-ignition engine fueled with DME. Single cylinder engine was equipped with common rail. Injection pressure was 700bar, dSOI between the main injection and the pilot injection was varied. Diesel was used as compared fuel of DME in all cases. The results was shown that maximum pressure was higher than all cases and its amount of DME and diesel was similar. Regardless the pilot injection, the main fuel injection timing was same. The heat release rate of the main injection for diesel was high while that of pilot injection for DME was high. The THC was very low regardless of the fuel type and injection strategy. In the single injection, NOx was increased to retard of main injection timing regardless of the fuel type. NOx emissions was decreased with the retardation of the main injection timing regardless of the fuel type in the case of 2-stage injection strategy.

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.26-36
• /
• 2012

Minimizing the cylinder wear and the consumption rate of cylinder oil in a large two-stroke diesel engine is of great economic importance. A motor-driven cylinder lubricator for Sulzer RT-flex large two-stroke diesel engines developed by authors is in need of mounting a quill system to lubricate cylinder parts for a smooth operation. In order to apply the common-rail lubricating system to the developed cylinder lubricator as the second research stage, the mechanical quill system with a progressively quantitative distributor (M.D.S.) is improved in the electronically controlled quill system with an accumulating distributor (E.D.S.). In this study, the effects of lubricator motor speed, plunger stroke and cylinder back pressure on oil feed rate and inequality rate are experimentally investigated by applying E.D.S. to the developed cylinder lubricator. It is found that the oil feed rate of E.D.S. is higher than that of M.D.S. because of the increase of delivery speed and volume by changing the role of accumulator in the same experimental condition. It can be also shown that, in E.D.S., the inequality rate is decreased a little or hardly unchanged as the cylinder back pressure and plunger stroke is elevated, while the inequality rate increased in M.D.S.. The inequality rates of E.D.S. and M.D.S. are lowered as the lubricator motor speed is increased.