• 한국안전학회지
• /
• 제31권5호
• /
• pp.89-94
• /
• 2016

The objective of this study was to estimate the dynamic behavior of a personal rapid transit(PRT) track system using a rail of rectangular tube section and a rail joint of sliding type, and to compare the results with the normal rail and rail joint of a PRT track system by performing field measurements using actual vehicles running along the service lines. The measured vertical displacement of rail and sleeper, and vertical acceleration of rail for the normal rail and rail joint section were found to be similar, and the rail joint of sliding type satisfied the design specifications of the track impact factor for a conventional railway track. The experimental results showed that the overall dynamic response of the rail joint were found to be similar to or less than that of the normal rail, therefore the rail joint of sliding type for PRT track system was sufficient to ensure a stability and safety of PRT track system.

• 문화기술의 융합
• /
• 제4권3호
• /
• pp.213-220
• /
• 2018

본 연구에서는 레일이음매를 배제할 수 없는 각관형 레일을 사용하는 PRT궤도구조를 대상으로 레일이음매 설치위치 및 간격을 최적화함으로써 레일이음매부의 충격 및 승차감 저하 현상을 최소화 하고자 수치해석 및 현장측정을 통해 열차주행 시 PRT 차량의 실 열차속도를 고려한 궤도 구조의 일반부 및 레일이음매부의 동적거동을 파악하여 레일이음매의 적정간격을 산정하였다.

• 한국철도학회논문집
• /
• 제4권1호
• /
• pp.31-37
• /
• 2001

There are three examples of noise reduction test by joint improvement. One of them is tested for electric car at joint rail and another is tested at expansion joint and long welded rail and the third is tested at open deck bridge. We can know from the result that the noise reduction effect of rail welding is very different to the type of track and the car. The condition of the test has some differences, but it may be useful reference of noise reduction

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.328-333
• /
• 2002

When vehicle travelling along the track which has irregularity such as vertical profile, dynamic forces arise at the Wheel/Rail contact patch by wheel/rail interaction. In particular short wavelength irregularities on dipped joint and small stiffness of connecting rail bring about intense wheel/rail dynamic effects at higher speed. In the paper, a new model for dipped joint rail is developed to study dynamic behavior of track. A cusp behavior on dipped joint was defined by its amplitude and decay factor, which was presented by FRA track classes. The result of case study are presented, which show wheel rail contact force in each track classes, train operation speed and bending flexible rigidity ratio of fishplates which are connecting the rail.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.922-927
• /
• 2007

The present urban maglev which has been developed in Korea is controlled by 4-edge control method over each bogie. The control output which is derived from two gap sensors and one vertical acceleration sensor controls magnet to maintain a nominal gap. But, the gap signal acts as a big disturbance in rail joint though two gap sensors are used and finally result in unstable response and poor ride comfort. This paper treats of a method to compensate the gap signal in rail joint for the levitation control of urban maglev. The physically abnormal change of gap is detected when one gap sensor passes a rail joint, the disturbance of gap in rail joint is estimated. Finally the disturbance in gap signal is eliminated by processing the information of vehicle speed and estimated disturbance in when the other gap sensor passes a rail joint.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.2125-2128
• /
• 2011

The continuous welded rail(CWR) track without the rail expansion joint has many advantages over the conventional track in a variety of fields including the speed-up and the ride comport. However, due to the excessive axial force in the CWR and the track-bridge interactive behavior, inevitably, the rail expansion joint must be installed at the vulnerable zone such as the bridge end zone, etc. In this rail expansion joint zone, the frequency of the maintenance work to repair the track irregularity is on the rise. This is because that the creep of the sleeper is occurred in the moveable zone of the rail expansion joint. In this study, among the several options for reducing the track irregularity on the rail expansion joint zone, the application and efficiency of the tied sleeper is investigated. Field test construction has been conducted, then the progress of the track irregularity and the frequency of the maintenance work are analyzed before and after the filed test construction.

• 한국철도학회논문집
• /
• 제3권1호
• /
• pp.19-26
• /
• 2000

The rail temperature is important to preserve the joint gap for standard length of rail and to determine the installation temperature which has direct influence on the rail buckling and failure in welded part for continuous welded rail(CWR), Therefore, we have measured and investigated various characteristics of rail temperature for each kind of rail. As the results of this, the correlation between the atmosphere temperature and the rail temperature which is commonly used by Korean Railway should be reconsidered. Also, the daily highest '||'&'||' lowest rail temperature was occurred when each temperature is higher and when it's lower. For the light rail, the rail temperature by the sun-light increases quickly and decreases late. But the time where the highest temperature is attained is same. There are some differences between the shade and sunny place about 3.0∼4.0$\^{C}$. The temperature of rail web is almost close to the conversion rail temperature for rail expansion. The wind of 1 m/s has an influence on the rail temperature around 5$\^{C}$.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.1174-1179
• /
• 2004

Field tests were conducted to investigate effects of a rail joint on the dynamic behavior of railway bridge. A four-span simpled supported plate girder bridge which has a rail joint on the third span was selected for tests. At the operating train loading, the induced vibration of the first and third span has been examined. The dynamic magnification ratio was used for quantitative analysis of impact effects caused by rail joint. The result of tests show that dynamic behavior of railway bridge picked up considerably due to a rail joint.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.570-573
• /
• 2004

Conventional methods for reducing vibration in engineering designs may be undesirable in conditions where size or weight must be minimized, or where complex vibration spectra exist. Some alloys with a combination of high damping capacity and good mechanical properties can provide attractive techanical and economical solutions to problems involving seismic, shock and vibration isolation. In this paper, it showed the noise and vibration characteristic was compared conventional rail joint to improved rail joint(damping alloy) for reducing noise and vibration. Its applicability to rail joint is discussed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.800-806
• /
• 2011

Thermal expansion which occurs at the high speed rail joint is proportional to the free length from the point of fixity. This thermal expansion behaves similar to free expansion because the girder longitudinal stiffness is much larger than longitudinal resistance of rail pads. But the longitudinal displacement in the long rail is nominal because the longitudinal support condition of the girder is normally MFM(movable-fix-movable) system. Due to these girder expansion characteristics, there is longitudinal relative displacement at the rail pad and rail fastener spring which connects rail and girder. If the relative displacement between rail and girder is beyond the elastic limit for the rail pad, rail fastener system shall be applied using sliding fastener to prevent rail pad damage and fastener separation resulting from slip. On the other hand, train vertical vibration and tilting can occur due to the lack of fastener vertical force if the sliding fastener is applied at the girder joint. In the high speed rail bridge, vibration can occur due to the spring stiffness of the elastomeric bearing, also both vertical downward and upward displacement can occur. The elastomeric bearing vertical movement can cause rail displacement and finally the stability of the ballast is reduced because the gravel movement is induced.