• Journal of Magnetics
• /
• v.20 no.2
• /
• pp.186-192
• /
• 2015

This paper describes the electromagnetic and mechanical characteristics of coaxial magnetic gear (CMG) with a low gear ratio. The analysis models are restricted to a CMG with a gear ratio of less than 2. The electromagnetic characteristics including transmitted torque and iron losses are presented according to the variation of the gear ratio. The pole pairs of high speed rotor are chosen as 6, 8 and 10 by considering the torque capability. As the gear ratio approaches 1, both iron losses on the ferromagnetic materials and eddy current losses on the rotor permanent magnets are increased. The radial and tangential forces on the modulating pieces are calculated using the Maxwell stress tensor. When the maximum force is exerted on the modulating pieces, the mechanical characteristics including stress and deformation are derived by structural analysis. In CMG models with a low gear ratio, the maximum radial force acting on modulating pieces is larger than that in CMG models with a high gear ratio, and the normal stress and normal deformation are increased in a CMG with a low gear ratio. Therefore, modulating pieces should be designed to withstand larger radial forces in CMG with a low gear ratio compared to CMG with a high gear ratio.

• Journal of Magnetics
• /
• v.20 no.4
• /
• pp.400-404
• /
• 2015

Various kinds of winding arrangements can be used to enable fault current limiters (FCL) to tolerate higher forces without resulting in a substantial increase in construction and fabrication costs. In this paper, a distributed winding arrangement is investigated in terms of its effects on the short-circuit forces in a three-phase FCL. The force magnitudes of the AC supplied windings are calculated by employing a finite element-based model in the time stepping procedure. The leakage flux and radial and axial force magnitudes obtained from the simulation are compared to those obtained from a conventional winding arrangement. The comparison shows that the distributed winding arrangement significantly reduces the radial and, especially, the axial force magnitudes.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.6
• /
• pp.112-119
• /
• 1995

Early fracture and cutting force of ceramic tool for hardened STC3 steel was investigated in this study. It was found that early fracture of ceramic tool was mostly occurred before normal wear was progressed beyond a critical cutting speed and normal wear was performed under the critical cutting speed. The relationships among critical cutting speed, which was a cause of early fracture, suggested cutting cross section, that is, maximum thickness of cut and width of cut, and cutting force were examined. The following conclusions were obtained: (1)Critical cutting speed showed a high value in the case of small maximum thickness of cut and large nose radius, but was not influenced by width of cut, (2)Principal, feed and radial force, respectively, showed the proportional value to constant cutting area, width of cut and maximum thickness of cut orderly, (3)Occurrence of early fracture was dependent upon radial force.

• Tribology and Lubricants
• /
• v.9 no.1
• /
• pp.45-54
• /
• 1993

The lubrication characteristics of line contacts between the vane and cam ring in an oil hydraulic vane pump with intravanes have been investigated. Variations of the radial acting force of a vane were calculated from previously measured results of dynamic internal pressures in four chambers surrounding a vane, and variations of the film thickness were estimated in both the rotational speed range from 500 to 1500 rpm and in the delivery pressure range from 1 to 14 MPa. The results indicate the variations of the radial acting force and film thickness. It is found that the regimes of lubrication in the vane tip contacts lover rigid-isoviscous to rigidvariable viscosities.

• Korean Journal of Hydrosciences
• /
• v.1
• /
• pp.61-71
• /
• 1990

The characteristics of radial thickness of ice jam at the center part of channel bends were analyzed briefly in this paper. Jam thickness in channel bends increases both toward the inner bank, and dowmstream. For this study, slope at the jam's underside was assumed to be liner with similarity of radial slope of bed in alluvial bends. Radial slope at the jam's underside in floating ice elements was estimated using the force equilibrium theory in the radial direction. The eqution which can be estimated the radial slope of ice jam was suggested using Falcon and Kennedy's bed layer theory. Experimental data, which were measured at the center part of cross-section in a single 180-degree bend, were compared to the calculated values using the suggested equtions. The result shows that the calcultated values were smaller than the measured ones. Ot is considered that the estimated value of shear stress in the radial direction may be smaller than the actual and two-layer model may be not suibable for alluvial bend flow.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1023-1027
• /
• 2004

Since the change of the radial electromagnetic force is a main cause of noise and vibration of the SRM, this paper proposes a method to reduce the change of the electromagnetic force of an SRM. The technique is based on the control of the current shape associated with each phase using switches of the converter to drive an SRM. And we analyze the relation between the derivative of the radial electromagnetic force and the phase currents. A simulation is given to demonstrate our results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.212-216
• /
• 2004

Bearingless motors are the rotational electric machine which utilize a common magnetic structure for rotation and magnetic suspension. Since the bearing function is combined with the motor, the shaft length can be shortened resulting in higher critical speeds. Relationship between suspension force and current of bearingless motor is clearly derived by prior research. However, relationship between displacement of rotor and suspension force is not precisely defined. In this paper, we present model of bearingless motor describing the radial force variation due to the movement of the rotor. Using a distributed magnetic circuit and maxwell stress tensor, we derived a mathematical expression for the radial force. For a slotless bearingless motor, we are able to find an analytical model presented in the form of stiffness. For a slotted motor, we can compute the stiffness by semi-analytical analysis. This model is validated by a finite-element-analysis.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.107-109
• /
• 2007

This paper presents a dynamic force analysis of switched reluctance motor using 2D-transient finite element method. The main exciting of the vibration is the electiromagnetic force in the stator that is calculated Maxwell stress method. The advantage for elimation of vibration of 12/8 SRM was explained by comparing the radial force of 12/8 and 6/4 SRM in both time and frequency domain. In order to effective mitigate the vibration during turning off process, effects of different commutation method were investigated.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.321-326
• /
• 2013

This paper investigates the magnetic excitation force of a surface-mounted permanent magnet (SPM) motor according to the change of pole/slot combination. The characteristics of magnetic flux and radial magnetic force (RMF) due to pole/slot combination were analyzed by using magnetic circuit analysis. Also, the RMF of motors with the variable pole/slot combination was numerically simulated by using the finite element analysis to verify the result of the magnetic circuit analysis. This research shows that RMF ripple is reduced when the number of pole is smaller than the number of slot.

• Journal of Magnetics
• /
• v.18 no.4
• /
• pp.432-442
• /
• 2013

For magnetically suspended flywheel (MSFW) with gimballing capability, demerits of Lorentz force-type magnetic bearings and common reluctance force-type magnetic bearings are analyzed, a novel reluctance forcetype magnetic bearing (RFMB) including radial and axial magnetic bearing units with 4 separate biased permanent magnets and two conical stators is presented. By equivalent magnetic circuits' method, its magnetic properties are analyzed. To reduce the eddy loss, it was designed as radial poles with shoes and its rotor made of Iron-based amorphousness. Although the uniformity of magnetic flux density in the conical air gap determines mainly the additional tilting torque, the maximum additional tilting torques is 0.05Nm and the rotor tilting has no influence on its forces when the rotor tilts or the maximum changes does not exceed 14% when the rotor drifts and tilts simultaneously. The MSFW with this RFMB can meet the maneuvering requirement of spacecraft theoretically.