• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.29-29
• /
• 2010

Engineering plastics have excellent electrical properties, mechanical strength and various characteristic which include chemical resistance, environmental resistance, weatherability at a wide temperature range. It has good characteristic(light weight, good productivity) as compare with epoxy or porcelain insulators. However, engineering plastics not suited to outdoor insulator because it isn't hydrophobic. Therefore, to over come these critical problems, we improve the surface insulation characteristics of engineering plastic by coating micro-, nano- size inorganic fillers added to RTV-SIR(Room temperature vulcanized-silicone rubber) at this plastic surface. The effect is analyzed through salt-fog test, tracking test. In conclusion, the engineering plastic coated RTV with micro-$Al_2O_3$20[phr], nano-Al(OH)3 1 ~ 3[phr] improved much better than the others.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 춘계학술대회 논문집
• /
• pp.29-29
• /
• 2010

Surface contamination and leakage current have caused operating problems. A flashover in a substation may result in destruction of an insulator or many others electrical equipment. Engineering plastics have good characteristic (light weight, good productivity and little of void) as compare with epoxy or porcelain insulators. Outdoor insulator must have resistance to contamination. However, it isn't suited to outdoor insulator because it is not hydrophobic. RTV(Room temperature vulcanizing) has a good property of hydrophobic and micro-filler. nano-filler have characteristics of obstructing exothermic reaction. In order to reduce the incidence of insulator flashover and damage, the silicon rubber contained with micro, nano-filler coating on surface of engineering plastics. In this paper, it compares tracking resistance, leakage current of the engineering plastic coated RTV with that of non-coated engineering plastic. And filled-composites performed much better than non-filled composites.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.688-693
• /
• 2003

The PSP technique has been used to measure pressure distribution on a model surface quantitatively. The objective of this study is to develop PSP technique which can be applied to low-speed flows. Four different PSP formulations including two porphyrins (PtOEP and PtTFPP) and two polymers (Poly(TMSP) and RTV-118) were tested and the performance of each combination was checked. In the static calibration, the luminescent intensity of the PSP coatings was measured from 0kPa to 11kPa with 0.5, 1, 2kPa increments. Among 4 PSP formulations tested, the combination of PtOEP and RTV-118 shows the best performance. The PSP technique was applied to an oblique impinging jet to measure the pressure field distribution on the impinging plate.

• The Journal of Advanced Prosthodontics
• /
• 제11권6호
• /
• pp.305-312
• /
• 2019

PURPOSE. The purpose of this study was to compare computer-aided design/computer-aided manufacturing (CAD/CAM) abutment and prefabricated abutment in Morse taper internal connection type implants after cyclic loading. MATERIALS AND METHODS. The study was conducted with internal type implants of two different manufacturers (Group Os, De). Fourteen assemblies were prepared for each manufacturer group and divided into 2 groups (n=7): prefabricated abutments (Os-P, De-P) and CAD/CAM abutments (Os-C, De-C). The amount of axial displacement and the removal torque values (RTVs) were measured before and after cyclic loading (10⁶ cycles, 3 Hz with 150 N), and the tensile removal force to dislodge the abutments was measured after cyclic loading. A repeated measures ANOVA and a pattern analysis based on the logarithmic regression model were conducted to evaluate the effect of cyclic loading on the axial displacement. The Wilcoxon signed-rank test and the Mann-Whitney test was conducted for comparison of RTV reduction% and tensile removal forces. RESULTS. There was no significant difference between CAD/CAM abutments and prefabricated abutments in axial displacement and tensile removal force; however, significantly greater RTV reduction% after cyclic loading was observed in CAD/CAM abutments. The correlation among the axial displacement, the RTV, and the tensile removal force was not significant. CONCLUSION. The use of CAD/CAM abutment did not significantly affect the amount of axial displacement and tensile removal force, but presented a significantly greater removal torque reduction% than prefabricated abutments. The connection stability due to the friction at the abutment-implant interface of CAD/CAM abutments may not be different from prefabricated abutment.

• 대한화학회지
• /
• 제48권3호
• /
• pp.266-272
• /
• 2004

소형 고체상 전극에 단일 조성 실온 경화형(one-component room temperature vulcanizing type) 실리콘러버 730(730 RTV)을 지지체로 도입하여 가소제가 필요 없는 탄산이온선택성 전극막을 개발하였다. 본 연구에서 최적화된 탄산이온선택성 전극막의 조성은 85.75 wt%의 730 RTV, 11.08 wt%의 trifluoroacetyl-p-decylbenzene(TFADB), 3.17 wt%의 tridodecyl-methylammonium chloride(TDMACl)로 제조 되었고, 우수한 전기화학적 특성(감응기울기 (26.3 mV/dec.), 선택성($logKT^{pot}_{CO_{2},Cl^-}$= -4.00, $logKT^{pot}_{TCO_{2},Sal^-}$=1.69), 검출한계(4.0${\times}10^{-4}M$))을 보였으며, 이와 같은 조성의 막을 도입한 평면형 고체상 센서는 60일 이상 초기특성을 유지하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.259-259
• /
• 2009

Surface contamination and leakage current have caused operating problems. A flashover in a substation may result in destruction of an insulator or many others electrical equipment. Engineering plastics have good characteristic (light weight, good productivity and little of void) as compare with epoxy or porcelain insulators. Outdoor insulator must have resistance to contamination. However, they are not suited to outdoor insulator by reason of being not good hydrophobic. RTV has a good property of hydrophobic and ATH has characteristic obstructing exothermic reaction. In order to reduce the incidence of insulator flashover and damage, the silicon rubber contained nano size ATH coat on surface of engineering plastics. In this paper, it compares resistance tracking of the engineering plastic coated RTV with that of non-coated engineering plastic and ATH filled composites performed much better than non-filled composites.

• 한국산학기술학회논문지
• /
• 제13권9호
• /
• pp.3895-3899
• /
• 2012

본 연구에서는 시작형 몰드재료인 실리콘 레진(RTV-3040)을 이용하여 엠보패턴을 활용한 몰드금형 개발을 위한 것이며, 상용패키지(Freeform)를 사용하여 필요한 패턴을 선택 한 후 면에 투영 엠보 면을 만들어 부품에 적용 가능을 검토하였다. 소량의 부품 개발 시 부식패턴이 필요로 한 제품들은 알루미늄 금형과 같은 시작형을 제작하여 대응하였으나, 부식패턴을 적용한 실리콘 금형 개발로 시간단축 및 원가절감이 가능한 것으로 나타났다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1449_1450
• /
• 2009

Surface contamination and leakage current have caused operating problems. A flashover in a substation may result in destruction of an insulator or many others electrical equipment. Engineering plastics have good characteristic (light weight, good productivity and little of void) as compare with epoxy or porcelain insulators. Outdoor insulator must have resistance to contamination. However, they are not suited to outdoor insulator by reason of being not good hydrophobic. RTV has a good property of hydrophobic and ATH has characteristic obstructing exothermic reaction. In order to reduce the incidence of insulator flashover and damage, the silicon rubber contained nano size ATH coat on surface of engineering plastics. In this paper, it compares resistance tracking of the engineering plastic coated RTV with that of non-coated engineering plastic and ATH filled composites performed much better than non-filled composites.

• 한국정밀공학회지
• /
• 제18권3호
• /
• pp.75-83
• /
• 2001

RIM(Reaction Injection Molding) is a widely used method to manufacture middle-large size outfit-part for a prototype car. The main advantage of RIM is the capability of manufacturing a small number of prototype parts with less cost and lead time than injection molding which is the most popular method to manufacture plastic parts. Generally, epoxy resin and RTV(Room Temperature Vulcanization) silicon are used as mold materials for RIM, and the selection of mold materials is usually depended upon the industrial environment of manufactures and it decides overall mold making process and part quality. This paper suggests a new mold making process by consolidating the advantages of epoxy resin and RTV silicon based RIM mold to enhance the parts quality while reducing the manufacturing cost and time and shows the competitiveness of the suggested process compared with conventional methods.

• Composites Research
• /
• 제17권5호
• /
• pp.61-67
• /
• 2004

본 연구에서는 전자파 차폐용 도전성 개스킷 소재로 활용할 수 있는 은입자 충전 실리콘 복합 페이스트에 대한 전기전도성 및 응력-변형율 특성을 분석하였다. 불규칙한 구형의 은(Ag)입자와 상온습기경화형(RTV) 실리콘수지를 도입하여 복합 페이스트의 퍼콜레이션 농도(임계 농도)를 전기전도도 측정 결과로부터 결정하였다. 약 28%의 은입자 함량에서 퍼콜레이션 현상이 발생하였으며, 이 농도에서 급격한 감소를 보이는 은입자/실리콘 복합 페이스트의 체적 비저항, 인장강도 및 연신률의 특성 변화에 관하여 고찰하였다. 또한, 커플링제의 선택적 방법을 통해 퍼콜레이션 농도 이상으로 충전된 복합 페이스트의 응력-변형율 특성을 효과적으로 개선할 수 있음을 제시하여 주었다.