• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2018-2023
• /
• 2003

An experiment is conducted for measuring the performance of an air tool, which is operated at 100,000 RPM at the unloaded state with the low torque. An experimental apparatus is developed as the power absorption type dynamometer. Inlet static pressure, flow rate, RPM and force are measured simultaneously. Torque, output power and specific output power are obtained. Those experimental results are compared with the experimental results obtained on a commercial dynamometer. However, no commercial dynamometers are available for measuring the torque above 30,000RPM. In order to use the commercial dynamometer, a reduction gear is applied to the shaft of dynamometer. Torque and power obtained on the commercial dynamometer show 50% lower than those obtained on a power absorption type dynamometer, because the inertia force is added to the air tool rotor for the braking system. Moreover, the starting RPM on the commercial dynamometer is less than 40,000RPM. From the compared results, they show that the power absorption type dynamometer should be applied for measuring the performance of an air tool operating at low torque and high RPM.

• Journal of Biosystems Engineering
• /
• 제28권2호
• /
• pp.97-106
• /
• 2003

One of the obstructing factors against managing dairy fm has been heavy labor requirement for feeding dairy cows. A Power-tiller TMF mixer was developed to reduce the cost and to provide economic benefit. The TMF mixer was desisted by the feeding capacity of 20∼30 heads at a batch with various functioning systems of auger type mixer, delivery conveyer, weighing console, pipe heater type heating system, power transmission train and mounting trailer. According to the study resulted, it showed that 1,200rpm, 1,600rpm, 2,000rpm and 2,300rpm were 6ps. Bps, lops and 12ps respectively. and that reduced shaft output by 15%. On the fodder mixer attached powertiller, initial output was necessary large torque. And the heating system was maintaining uniform temperature 60$^{\circ}C$ relatively.

• International Journal of Control, Automation, and Systems
• /
• 제4권3호
• /
• pp.359-364
• /
• 2006

This article describes the useful way to measure the torque and RPM of the geared motor. For this we have made the planetary geared reduction motor including 2 Hall sensors in it and the monitoring system. The monitoring system displays the sensing values (torque, rpm) and the calculated value (power) and it also has the network capability using the Bluetooth protocol. We will show that our solution is much more inexpensive and simple method to measure torque and rpm than before.

• 한국항해항만학회지
• /
• 제30권3호
• /
• pp.241-245
• /
• 2006

선박에서 발생되는 밸러스트수를 전처리하기 위하여 수중에 포함되어 있는 입자상 오염물질과 수중생물체를 자동역세척 여과장치를 이용하여 처리한 결과를 나타내었다. 밸러스트수를 처리하기 위한 전처리의 장점은 입자상의 오염물질을 제거하여 후처리공정의 처리효과를 높이는데 있다. 여과필터의 회전속도가 20rpm에서는 여과압력이 40.5mmHg이고, 40rpm 에서는 36.6mmHg이며 60rpm 이상에서는 35mmHg로 나타나 연속적으로 여과할 수 있었다. 필터의 막힘현상으로 역세 회복압력과 역세간격은 시간의 경과에 따라 조금씩 감소하고 처리유량도 감소하는 것을 관찰할 수 있었다. 회분식 여과처리공정은 자동 역세척을 수행하는 공정에 비해서 처리효율의 저하가 일어났다. 여과 처리를 통하여 $70{\mu}m$이상의 식물성 플랑크톤과 동물성 플랑크톤을 포함하는 수중생물체를 제거할 수 있었다. 실험결과를 통하여 밸러스트수 처리에 적용 가능한 기술임을 알 수 있었다.

• 한국양식학회지
• /
• 제16권3호
• /
• pp.142-150
• /
• 2003

Performance of a biological filter, the rotating biological contactor (RBC), is affected by rotational speed and hydraulic residence time (HRT). A RBC with a disc diameter of 62 cm, total surface area of 48.28 $m^2$, volume of 0.34 ㎥, and submergence ratio of 35.4% was tested for the combinations of five rotational speeds (1, 2, 3, 4 & 5 rpm) and three HRT (0.5, 1.0 & 2.0 hr) to find out the maximum removal efficiencies of total ammonia nitrogen (TAN) and nitrite nitrogen of a simulated recirculating aquaculture system. Ammonia loading rate in the system was 25 g of TAN/ ㎥. day. Removal efficiencies were checked when TAN concentrations in the system stabilized for 3 days in each treatment. The concentration of TAN in the system decreased with increasing rotational speed of the RBC up to 4 rpm in all HRT (P<0.05). At the rotational speed of 5 rpm, the efficiencies decreased in all HRT (P<0.05). When the rotational speeds were 1, 2, 3, 4, and 5 rpm, TAN concentrations in the system were 1.35, 0.94, 0.69, 0.66, and 0.76 mg/L at the 0.5 hr HRT, 2.86, 1.18, 0.96, 0.87, and 1.11 mg/L at the 1.0 hr HRT, and 5.30, 2.44, 1.99, 1.77, and 2.01 mg/L at the 2.0 hr HRT, respectively. The TAN removal efficiencies of the RBC at the rotational speeds of 1, 2, 3, 4, and 5 rpm were 32.9, 49.5, 65.1, 72.9, and 62.9% in 0.5 hr HRT,33.1, 74.1, 87.1, 95.8, and 78.5% in 1.0 hr HRT, and 35.5, 76.7, 89.6, 97.0, and 85.5% in 2.0 hr HRT, respectively. TAN removal efficiency of RBC per pass increased with increasing HRT. However, TAN concentration in the system also increased. The best operating condition among the treatments was obtained at the treatment of 0.5 hr HRT and 4 rpm (P<0.05). The TAN concentration was 0.66 mg/L. Concentrations of nitrite nitrogen (NO$_2$$^{[-10]}$ -N) in the system decreased with increasing rotational speed in all HRT while that in the system increased with increasing HRT in all rotational speeds. The ranges of NO$_2$$^{[-10]}$ -N concentrations at HRT of 0.5, 1.0, and 2.0 hr in the system were 0.26~0.32, 0.31~0.56, and 0.43~l.45 mg/L, respectively. The ranges of daily removal rates of TAN in this system were 20.03~23.0 g TAN/㎥ㆍday and those of nitrite nitrogen were 19.65~30.25 g NO$_2$$^{[-10]}$ -N/㎥ㆍday.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.521-527
• /
• 2001

The dynamic performance analyses and tests for a 50kW turbo-generator (KIMM-TG50) were carried out. The operating concept of this machine is that it gets the initial driving force from the built-in motor-generator until it reaches its self-sustaining speed of 40,000 rpm, and then the driving mode is changed to self-operating mode by the combustor installed between the centrifugal compressor and the turbine. Due to winding mistake of motor-generator, the system could go only up to 22000 rpm by the motor so that high pressure air externally fed into the turbine was utilized to get the system to run up to 62,000 rpm thereafter. The vibration data collected during the tests revealed that the first bending critical speed is in near 5,600 rpm as predicted in the design stage of the rotor-bearing system, and that there were no other identifiable critical speeds up until 62,000 rpm due to high damping from the squeeze film damper-bearings supporting the rotor. This paper presented some of the experimental results along with dynamic performance predictions made in the design stage as a part of progress being made.

• 수산해양기술연구
• /
• 제36권3호
• /
• pp.157-165
• /
• 2000

연안 소형 어선의 조업 효율을 향상시키기 위한 연구의 일환으로 소형 유압식 어로윈치시스템을 설계하고, auto tension 기능을 내장시켜 이 시스템의 개루프 상태에 대한 동적 응답 특성을 분석, 고찰한 결과를 요약하면 다음과 같다. 1. 본 연구에서 설계, 제작한 소형 윈치시스템은 갑판상 어느 장소에서도 조작이 가능하도록 원격조작방식을 채용하고 있기 때문에 어로 작업시의 인력 감소와 작업의 효율성을 높일수 있다고 생각된다. 2. 솔레노이드 밸브를 ou/off 조작하여 윈치를 구동할 때, 정전 및 역전 구동 조작에 대한 윈치 드럼의 회전 지연시간(dead time)은 각각 0.09 sec, 0.04 sec이었다. 또한 on/off 레버의 조작을 행한 직후 응답 특성은 약간 불안정하였지만, 짧은 경과 시간을 거쳐 안정되는 추종성능을 나타내었다. 3. 윈치를 auto tension mode로서 구동하는 경우, 윈치의 회전축에 55.9 kgf$.$m 이상의 토오크가 작용하면 윈치는 5.1 rpm의 회전속도로서 줄을 풀어내고, 그 이하의 토오크가 작용하면 11.1 rpm의 회전속도로서 줄을 감아들이는 자동 권양 윈치의 기능을 발휘한다. 4. 윈치의 auto tension mode에 대한 과도 응답에서 부하가 급격히 증가할 때와 감소할 때의 정정 시간은 0.12 sec, 0.2sec이었고, 그 때의 회전속도는 각각 11 rpm, 5.3 rpm이었다. 5. 원격제어조작에 따른 윈치의 토오크 및 회전속도에 대한 추종성능은 정전 구동에 있어서는 0.23 sec, 역전 구동의 경우에 있어서는 0.37 sec 이내로서 비교적 안정된 응답 특성을 나타내었다. 이상의 결과로부터 본 연구에서 설계한 소형 어선용 자동 권양 윈치 시스템은 인력을 절감하고, 부하의 급속한 변화에 대한 추종 성능이 현용 어로시스템에 비하여 매우 우수하기 때문에 해상에서 어로작업시 과부하에 대한 어구의 손상 방지 및 조업 효율의 향상에 크게 기여할 것으로 판단된다.

• Journal of Biosystems Engineering
• /
• 제16권2호
• /
• pp.148-158
• /
• 1991

This study was undertaken to develop the feed rate control system for the head feed thresher by making use of the microprocessor and to evaluate the response of the system to a various threshing conditions. It was verified the performance of the control system through experiments. Control conditions were determined based on the simulation results of control system. The control system set at RH=500rpm, RL=480rpm for the bundle feed was considered optimum to give a high threshing capability and still to stabilize the feeding seed regardless of the bundle size. The control system for the continuous spread feed set at the range of LH=15mm, and LL=12mm gave a high control performance for the feeding mass of 1.1Kg/m and lower tested. In addition, the feed rate proportionality constant should be set lower than one in order to keep the rotational speed of threshing cylinder within the range of 500~520rpm.

• 한국초전도ㆍ저온공학회논문지
• /
• 제2권1호
• /
• pp.7-13
• /
• 2000

A rotating cryogenic system was designed similar to the cooling system for the rotor of a superconducting generator. The experimental rotor has an inner vessel which simulates the winding space of an actual superconducting rotor, and a torque tube of comparable design. This paper describes the evaluation of the total heat leak into the inner vessel that leads to the study of the heat transfer characteristic of the rotating cryogenic system. To examine the insulation performance of the experimental rotor. temperature was measured at each part of the system at various rotaing speeds from 0 rpm to 600 rpm. Total heat leak into the inner vessel was calculated by measuring the boil-off rate of liquid helium. Conduction heat leak to the inner vessel was obtained by the vent tube, and radiation heat leak was calculated by subtracting the conduction heat lent from the total heat leak. There seemed to be no rotaional dependency of total heat leak at least up 600 rpm.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2005년도 추계학술대회 논문집
• /
• pp.181-185
• /
• 2005

선박에서 발생되는 밸러스트수를 전처리하기 위하여 수중에 포함되어 있는 입자상 오염물질과 수중생물체를 자동역세척 여과장치를 이용하여 처리한 결과를 나타내었다. 밸러스트수를 처리하기 위한 전처리의 장점은 입자상이 오염물질을 제거하여 후처리공정의 처리효과를 높이는데 있다. 여과필터를 회전하여 20RPM 에서는 40.5cmHg이고 40RPM 에서는 36.6cmHg이며 60RPM 이상에서는 35cmHg로 나타나 연속적으로 여과할 수 있었다. 필터의 막힘현상으로 역세 회복압력과 역세간격은 시간의 경과에 따라 조금씩 좁아지고 처리유량도 감소하는 것을 관찰할 수 있었다. 회분식 여과처리공정은 자동 역세척을 수행하는 공정에 비해서 처리효율의 저하가 일어났다. 여과처리를 통하여 $80{\mu}m$이상의 식물성 플랑크톤과 동물성 플랑크톤을 포함하는 수중생물체를 제거할 수 있었다. 연구결과를 통하여 밸러스트수 처리에 적용 가능한 기술임을 알 수 있었다.