• 한국유체기계학회 논문집
• /
• 제16권3호
• /
• pp.18-25
• /
• 2013

Recently the requirement of long-term mobile energy source for mobile robot or small-sized unmanned vehicle is highly increased, and the micro turbine generator(MTG) which is known to have high energy and power density is under development. MTG is designed to have air foil bearing and high speed rotor of which operating speed is 400,000rpm. In the development stage of high speed rotor and bearing, stability analysis for the full operational speed range is essential and the dynamic coefficients such as stiffness and damping coefficients of bearing depending on the rotational speed are required for that. Although perturbation method is usually used to identify the dynamic coefficients, it's not easy to give the perturbation to the high speed rotating rotor. In this study, we present the dynamic coefficients measurement system for air foil bearing which consists of electromagnets, gap sensors, high speed motor and controller. This measurement system can exert the sine sweep force to the rotor-bearing, measure the displacement of rotor and get FRF(Frequency response function) of rotor-bearing. The least square estimation method is applied to identify the dynamic coefficients of bearing from the measured frequency response at the different rpm and the identified dynamic coefficients for the wide rotational speed range are presented.

• 한국도로학회논문집
• /
• 제11권3호
• /
• pp.85-95
• /
• 2009

2007년 경찰청 통계자료에 따르면 사업용 차량(시내, 시외, 기타버스)의 교통사고 건수는 당 해 교통사고 건수의 3.5%에 해당하지만 사업용 차량의 경우 운전자 외 다수 승객의 안전을 책임져야 하므로 더욱 심각한 사회적, 경제적 문제를 초래한다. 이러한 사업용 차량의 교통사고 감소 및 안전운전에 대한 사회적 요구에 부흥하기 위하여 디지털 주행기록계, 차량용 블랙박스 등 다양한 형태의 시스템이 사용되고 있으나, 이러한 시스템은 사고 후 차량데이터를 기반으로 위험운전여부를 분석하여 운전자를 관리하기 때문에 실시간으로 운전자를 관리하기에는 큰 한계가 있다. 또한 현재 운영되고 있는 주행기록계는 운전자에게 경고 정보를 제공하지만 실제 위험운전 여부와 상관없이 차량의 속도와 RPM정보만을 이용하여 운전자에게 경고를 제공하고 있어 효율이 매우 떨어지는 실정이다. 이에 본 연구의 선행연구에서는 차량 운전자의 운전행태에 따른 차량 동역학 데이터를 저장?판단하여 운전자에게 실시간으로 경고정보를 제공해 줄 수 있는 위험운전 판단장치를 개발하였으며, 개발된 위험운전 판단장치에서 운전자의 안전운전을 향상 시킬 수 있는 위험운전 유형에 따른 임계값을 개발하였다.

• 산업경영시스템학회지
• /
• 제33권2호
• /
• pp.154-161
• /
• 2010

The conning display which is located in the ship bridge shows the various important information such as ship position, ship speed, track data, rate of turn, thruster rpm so on, and is one of the IBSs(Integrated Bridge Systems). In this study, the survey was conducted for ten officers to find the importance and using frequency of the information which were displayed in the conning display. The results showed that the information of drift speed, ship speed, wind direction and wind force, rate of turn, sea water depth, ship position, heading, thrust rpm, alarm, rudder command and angle got high scores and it meant that these information were very important and high frequency of use during the navigation. The optimized contents arrangement in conning display was suggested based on importance and using frequency of information. The experiment using eye-tracking system was conducted to compare the performance time and error rate of nine different scenarios for suggested arrangement display and three other existing displays. The results showed that the suggested arrangement was the best in performance time and error rate. The scenario concerning the direction and speed of wind showed faster performance time and lower error rate than other scenarios. The movement of subject's eye tended to search from the center and to avoid the comer, called 'the comer effect.' It is expected that the results of this study could help for the bridge staff to grasp the sailing information easily and to cope with the given situations promptly.

• International Journal of Aerospace System Engineering
• /
• 제2권1호
• /
• pp.1-5
• /
• 2015

The Unmanned Air Vehicle (UAV) systems are indispensable tools of air surveillance and reconnaissance nowadays. Via this systems, hazardous end risky intelligence gathering activities are handled easily. Although they are named as "Unmanned" the UAV systems are commanded by pilots/operators. So, because of weather conditions, enemy attacks etc. as well as pilot error it is possible to face with sudden Round per Minute (RPM) drops and subsequently engine cut/stop during a mission flight at high altitudes. In this case, there are some very urgent decisions to make and rapid "emergency procedure" steps to take in a very short time before Line of Sight (LOS) is lost. The time before crash and the distance to landing air base need to be calculated, the Return Home route need to be checked and the landing/crash side need to be determined. Therefore it is a vital necessity that UAV pilots have some extra qualifications like being determined, well instructed and trained, experienced apart from operating ability. Within this scope, for an education process of a UAV pilot experience sharing and lessons learned are as important as simulators even more. By means of lessons learned it is possible to find out the reasons, mistakes and prevent the likely UAV accidents. In this study it is told about a real UAV crash, experienced of the pilot, the dos and don'ts and the difficulties. Thus it is aimed to help the people who can experience the same or similar situations in future.

• Journal of Biosystems Engineering
• /
• 제7권2호
• /
• pp.72-85
• /
• 1983

Rice whitening is performed by basically two different whitening actions known as abrasive and frictional. The former adopted in the emery stone abrasive type whiteners and the latter in the jet-air friction type. Comparative milling yields and whitening efficiencies between the whitening system consisting of jet-air friction type whiteners only and the system consisting of both abrasive- and jet-air friction-types have not yet been rigorously defined. This study was to examine the effect of combined operations of abrasive- and jet-air friction-type rice whiteners on milling yields and whitening efficiencies. The small capacity commercial units of the abrasive- and friction-type whiteners were used for the experiments. The combinations of whitening treatments were: 1) Once in the abrasive type and then two to three times in the friction type, 2) twice in the abrasive and then two to three times in the friction type and 3) three to five times in friction type. In these tests, counter pressures for the friction type whiteners were established differently as required to get about the same degree of whitening at the end of predetermined numbers of the repeated operations. The speed of emery stone and the slot angle of the screen were also the factors varied in the abrasive type whitener. Sheukwang rice variety having 13.05% M.C. was used in the tests. The dependent variables were the milled- and head-rice recoveries and electricity consumption. The results of the study are summarized as follows: 1. It was found that in the whitening systems consisting of abrasive- and friction-type whiteners slot angle of the screen, the rotational speed of emery stone roller had significant effect on the milling yields and whitening efficiency. In general, the increase of the emery stone roller speed from 690 to 950 rpm presented a positive effect on milling yield, and one-pass abrasive milling combinations had higher milling yields than two-pass abrasive milling combinations. 2. It was apparent that if the slot angle of the screen and the speed of emery stone roller are modified and set at an optimum level, the combination whitening system consisting of abrasive- and friction-type whiteners is better than the pure frictional whitening system consisting of jet-air friction type in terms of milling yields and efficiencies. 3. In the rice whitening system consisting of abrasive- and jet-air friction-type whiteners, the best whitening performance was obtained when the slot angle of the screen and the rotational speed of emery stone roller were $45^{\circ}$ and 950rpm, respectively, for the one-pass abrasive milling combinations. However, for the two-pass abrasive mi11ing combinations, the best performance was obtained with $75^{\circ}$ of slot angle and 950 rpm of the emery stone roller speed. 4. As compared with pure frictional whitening systems, the combination systems produced more milled rice by 0.8-1.0% point and more head rice by 0.5-1.5% point, and consumed less electricity by 0.15-0.20 KwH per 100kg of milled rice when the abrasive whiteners were operated in the modified conditions as described in item 3 above. Further study is recommended to find out optimum operational and design conditions of abrasive type whiterners.

• 항공우주시스템공학회지
• /
• 제14권5호
• /
• pp.42-48
• /
• 2020

본 논문은 2행정 피스톤 엔진 기반 발전기 및 배터리로 구성된 드론용 전기추진시스템 설계 과정에 대해 다룬다. 연구의 목적은 하이브리드 시스템의 높은 에너지 밀도를 이용하여 비행시간을 증가 시키고 화석연료 사용량을 줄임으로써 환경 변화에 대처함에 있다. 시스템은 6 kW의 출력을 생산할 수 있고, 엔진 RPM 제어를 통해 부하 요구에 맞는 출력 조절이 가능하다. 또한 배터리를 추가 장착함으로써 출력 보완재 역할 뿐만 아니라 비상시 제한된 시간 내 주 전력으로 사용할 수 있다. 또한 발전기를 엔진 크랭크축에 직접 연결함으로써 설계 복잡성을 줄여 동체 내 공간 활용성을 증대 시켰다.

• 한국자동차공학회논문집
• /
• 제20권6호
• /
• pp.107-116
• /
• 2012

In this study, the trucks(2.9-liter) have been developed to use DME as fuel, and performance test of the vehicle's DME engine, power, emissions, fuel economy and vehicle aspects was conducted. For experiments, the fuel system(common-rail injectors and high-pressure pump included) and the engine control logic was developed, and ECU mapping was performed. As a result, the rail pressure from 40MPa to approximately 65% increase compared to the base injector has been confirmed that. Also, the pump discharge flow is 15.5 kg/h when the fuel rail pressure is 400rpm(40MPa), and the pump discharge flow is 92.1 kg/h when the fuel rail pressure is 2,000rpm(40MPa). The maximum value of full-load torque capability is 25.5 kgfm(based on 2,000 rpm), and more than 90% compared to the level of the diesel engine were obtained. The DME vehicle was developed in this study, 120 km/h can drive to the stable, and calculated in accordance with the carbon-balance method of fuel consumptions is 5.7 km/L.

• Journal of Biosystems Engineering
• /
• 제41권1호
• /
• pp.12-20
• /
• 2016

Purpose: Pepper prices have risen continuously because of a decrease in cultivation area; therefore, mechanical harvesting systems for peppers should be developed to reduce cost, time, and labor during harvest. In this study, a screw type picking head for a self-propelled pepper harvester was developed, and the optimal working conditions were evaluated considering helix types, winding directions of helix, and rotational speeds of the helix. Methods: The screw type was selected for the picking head after analyzing previous studies, and the device consisted of helices and a feed chain mechanism for conveying pepper branches. A double helix and a triple helix were manufactured, and rotational speeds of 200, 300, and 400 rpm were tested. The device was controlled by a variable speed (VS) motor and an inverter. Both the forward and reverse directions were tested for the winding and rotating directions of the helix. An experiment crop (cultivar: Longgreenmat) was cultivated in a plastic greenhouse. The test results were analyzed using the SAS program with ANOVA to examine the relationship between each factor and the performance of the picking head. Results: The results of the double and triple helix tests in the reverse direction showed gross harvest efficiency levels of 60-95%, mechanical damage rates of 8-20%, and net marketable portion rates of 50-80%. The dividing ratio was highest at a rotational speed of 400 rpm. Gross harvest efficiency was influenced by the types of helix and rotational speed. Net marketable portion was influenced by rotational speed but not influenced by the type of helix. Mechanical damage was not influenced by the type of helix or rotational speed. Conclusions: Best gross harvest efficiency was obtained at a rotational speed of 400 rpm; however, operating the device at that speed resulted in vibration, which should be reduced.

• 융복합기술연구소 논문집
• /
• 제2권1호
• /
• pp.24-30
• /
• 2012

In this study, the trucks(2.9-liter) have been developed to use DME as fuel, and performance test of the vehicle's DME engine, power, emissions, fuel economy and vehicle aspects was conducted. For experiments, the fuel system(common-rail injectors and high-pressure pump included) and the engine control logic was developed, and ECU mapping was performed. As a result, the rail pressure from 40MPa to approximately 65% increase compared to the base injector has been confirmed that. Also, the pump discharge flow is 15.5 kg/h when the fuel rail pressure is 400rpm(40 MPa), and the pump discharge flow is 92.1 kg/h when the fuel rail pressure is 2,000rpm(40MPa). The maximum value of full-load torque capability is 25.5kgfm(based on 2,000rpm), and more than 90% compared to the level of the diesel engine were obtained. The DME vehicle was developed in this study, 120 km/h can drive to the stable, and calculated in accordance with the carbon-balance method of fuel consumptions is 5.7 km/L.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.1006-1011
• /
• 1991

In this paper, a neural network estimator which estimates the output of the wide range oxygen sensor is proposed, The neural network estimator is constructed to give the output of the wide range oxygen sensor from rpm, fuel injection time, throttle position, and output voltage of the exhaust gas oxygen sensor. And, using this estimator, PI controller for air-fuel ratio control is designed. Experiment results show that the proposed method gives good results for SONATA engine under light load and constant rpms.