• Journal of the Korean Solar Energy Society
• /
• v.32 no.3
• /
• pp.1-10
• /
• 2012

The purpose of this study was to promote the utilization of wind velocity of kitchen and bathroom exhaust ducts for wind power generation in high-rise apartments. The research content can be summarized as follows: 1) Nine high-rise apartments were examined for the installation of kitchen and bathroom exhaust ducts located in the pipe shaft (PS) section. After selecting simulation candidates, a simulation was performed with the STAR-CCM+ Ver 5.06 program. 2) Of nine high-rise apartments, seven had kitchen and bathroom exhaust ducts, whose cross section was in the range of $0.16m^2{\sim}0.4m^2$. The area ratio between the exhaust ducts and PS section (cross section of exhaust duct/area of PS section ${\times}$ 100) was on average 3.2%. 3) The simulation results were analyzed. As a result, the smaller cross section kitchen and bathroom exhaust ducts had, the more advantages there were for increasing exhaust wind velocity. If an out air inlet duct is installed to the old kitchen and bathroom exhaust ducts, it will increase exhaust wind velocity by 3.01~3.98m/s and contribute to the proper wind velocity level (3.0m/s). 4) When the simultaneous usage rate between the kitchen and bathroom exhaust fan increased from 20% to 60%, exhaust wind velocity increased. The "entire house holds" condition for exhaust fan operation provided more even exhaust wind velocity than the "some house holds" condition. 5) Exhaust wind velocity increased in the order of amplified (T-3), induced (T-2) and vertical (T-1) top of kitchen and bathroom exhaust ducts. Of them, the amplified type (T-3) was under the least influence of external wind velocity and thus the most proper for kitchen and bathroom exhaust duct tops.

• Steel and Composite Structures
• /
• v.21 no.1
• /
• pp.217-247
• /
• 2016

Five extended cylindrical reticulated shells are proposed by changing distribution rule of diagonal rods based on three fundamental types. Modeling programs for fundamental types and extended types of cylindrical reticulated shell are compiled by using the ANSYS Parametric Design Language (APDL). On this basis, conditional formulas are derived when the grid shape of cylindrical reticulated shells is equilateral triangle. Internal force analysis of cylindrical reticulated shells is carried out. The variation and distribution regularities of maximum displacement and stress are studied. A shape optimization program is proposed by adopting the sequence two-stage algorithm (RDQA) in FORTRAN environment based on the characteristics of cylindrical reticulated shells and the ideas of discrete variable optimization design. Shape optimization is achieved by considering the objective function of the minimum total steel consumption, global and locality constraints. The shape optimization for three fundamental types and five extended types is calculated with the span of 30 m~80 m and rise-span ratio of 1/7~1/3. The variations of the total steel consumption along with the span and rise-span ratio are analyzed with contrast to the results of shape optimization. The optimal combination of main design parameters for five extended cylindrical reticulated shells is investigated. The total steel consumption affected by distribution rule of diagonal rods is discussed. The results show that: (1) Parametric modeling method is simple, efficient and practical, which can quickly generate different types of cylindrical reticulated shells. (2) The mechanical properties of five extended cylindrical reticulated shells are better than their fundamental types. (3) The total steel consumption of cylindrical reticulated shells is optimized to be the least when rise-span ratio is 1/6. (4) The extended type of three-way grid cylindrical reticulated shell should be preferentially adopted in practical engineering. (5) The grid shape of reticulated shells should be designed to equilateral triangle as much as possible because of its reasonable stress and the lowest total steel consumption.

• Journal of the Korean Society of Safety
• /
• v.30 no.5
• /
• pp.8-13
• /
• 2015

Molded Case Circuit Breakers (MCCBs) are typically used to provide over current protection for electrical safety caused by short circuit faults and overloads in indoor low voltage power systems. The MCCB automatically connects and disconnects loads from the electrical source when the current reaches a value and duration that will cause an excessive. However, the MCCB sometimes is not interrupted due to a malfunction, nuisance tripping, or in a fire. Ensuring electrical safety is very important in a indoor low voltage power system. This paper presents the operating characteristics of MCCBs according to a temperature rise from room temperature to 160 degrees Celsius delivered by a radiant panel heater. The ABS 54c(rated current: 30A) of the hydraulic magnetic trip type was used in the experiments. The signals of temperature, voltage, and current were measured using the high accuracy Signal Conditioning Extensions for Instrumentation (SCXI) measurement system with the LabVIEW program manufactured by National Instruments. The operating characteristics were measured as functions of current amplitude and ramp-up rate. The MCCB tripping time decreased as a result of increasing current amplitude and ramp-up rate under a temperature rise condition, because the temperature and level of the current are directly proportional to the tripping time. Additionally, an instantaneous operation was observed after 8 times of the rated current, and the MCCB began to melt a surface temperature of around 300 degrees Celsius of. The experimental results coincided well with the operating curve.

• Journal of Environmental Health Sciences
• /
• v.46 no.2
• /
• pp.128-135
• /
• 2020

Objective: The objectives of this study are to report the number of humidifier disinfectant (HD) associated health problems, including HD associated lung injury (HDLI), by year. This data was analyzed by the type of HD and HD brand. Methods: A total of 530 patients registered with the national program on HD through its third round were distributed based on the year when they developed their first health problem including HDLI (N=221). The distribution of health problems at diagnosis was clinically evaluated in order to examine the association between their lung injury and the use of HD. Results: The number of HD associated victims and HDLI patients was found to rise sharply from 2008 to 2011, with a peak in 2011. This trend was found not only for HD brands containing polyhexamethylene guanidine phosphate (PHMG), but also chloromethylisothiazolinone/methylisothiazolinone (CMIT/MIT). The number of patients who responded as developing health problems in the specific year was 35 for 2008, 51 for 2009, 108 for 2010 and 182 for 2011. Other types of HD brands and HD chemicals did not follow the trend of abrupt increase in HD associated patients since 2008. Conclusion: This study found the number of HD associated victims and HDLI patients who used HD brands containing PHMG sharply increased starting in 2008. A significant change in the process of manufacturing PHMG can be suspected with the abrupt rise in HD associated patients in specific years.

• Journal of the Society of Disaster Information
• /
• v.8 no.2
• /
• pp.148-157
• /
• 2012

Recently, evacuation safety of building residents becomes the major concern, as the building has been higher and more complicated. Many high-rise multi use buildings are under construction in Korea. Required evacuation time using stairway is longer in high-rise buildings, moreover it is impossible for the disabled to evacuate by using stairway. For this reason the study on the effectiveness of using elevator for evacuation is being progressed. Elevator shaft flow coefficient is the major factor for the calculation of elevator piston effect. The results of this study can be used for the study of elevator piston effect as basic data. The flow coefficient simulation was performed using FLUENT, commercial CFD program. As a result of the flow coefficient simulation, the coefficient is 0.88 considering the safety factor. This result is verified that the result of experimental study, 0.86 is conservative.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.11 no.2
• /
• pp.9-13
• /
• 2011

The Performance-based fire protection design required to construct super high-rise building is the active measure for the evaluation of fire risks and the establishment of fire protection systems on the basis of engineering analysis, which is more efficient and proper than existing prescriptive-based design. This study applied time-line analysis of RSET is required safe egress time and ASET is available safe egress time with the fire and evacuation simulation to analyze. The result of this study showed the sprinkler system increased ASET and fire detection and alarm system reduced RSET efficiently. Reduced evacuation time influences to secure the life safety. Also it is essential to maintain the fire suppression system and fire detection & alarm system properly. Database of fire movement and evacuation action program are useful for the performance-based design.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.4
• /
• pp.85-92
• /
• 2009

Urban regeneration projects have been actively proceeding all over Korea. Urban regeneration has become a critical issue in the domestic construction industry, with environmental-friendly construction and high-rise buildings being emphasized. Because these projectstend to become complex, urban regeneration projects require interest and approach on a level of program management that includes traditional project management. This paper develops aprototype for a new program management information system of a supports the promotion of urban regeneration projects through the deduction of the requirements about system. The prototype of the program management information system includes functions that supply diverse information, support the process and legislation of an urban regeneration project, manage stakeholders, support decision-making, estimate and manage program risks, and manage the program level.

• Architectural research
• /
• v.21 no.3
• /
• pp.59-67
• /
• 2019

Although many stadiums around the world have incorporated various profitable facilities, many are making conventional and cursory decisions without deep consideration of the interrelationships of different programs. This paper investigates cases in which new programs such as a hotel, a youth hostel, and a dormitory have been introduced into stadiums, showing different results. In the first part of this paper, the theoretical precedents of program combination are studied. Although Bernard Tschumi's notion of the combination of different programs presented its prophetic probability, this paper discern different approaches addressing program mixture, engendering eventually a productive modification of his notion based on the empirical observation of the cases. This paper classifies the manner of programmatic combination into complexity and hybridity, arguing that the latter transforms the spaces and gives rise to unexpected synergy, while the former merely assembles different programs. The second part compares the spaces of complexity and hybridity in stadiums. Through the plan and the section analysis of the spatial structure and the interrelationship of programs, this section reveals how the two different ways of the program combinations have had different results. In hybrid stadiums, programs are not simply gathered, but directly connected and intertwined. In the third part, the nature of the spatial transformation in the hybrid space is researched in detail. In the hybrid stadiums, the collision of the different programs changes the conception of the programs themselves and their related spaces. Hotels and stadiums are not what they once were, provoking unanticipated situations. These transformed spaces not only suggest a method of reutilizing of disused urban spaces, but also of meaningful and communicative program mixture, diversifying and vitalizing a city, not isolated islands of discrepancy. The ultimate purpose of this paper is clarifying the programmatic hybrid paradigm, surpassing complexity through the analysis of the stadium cases and illuminating the manner by which the hybridity breaks the typical tie between the program and space, to cause transformed situations.

• KDI Journal of Economic Policy
• /
• v.12 no.3
• /
• pp.3-26
• /
• 1990

Encouraged by the investment in the rice paddy, the introduction of new varieties (Tong-Il), and the price support program, there has been great success in increasing rice production. Meanwhile, the demand for rice has decreased rapidly as per capita income continues to rise. Rice self-sufficiency has been attained, and a new over-supply problem is emerging. Moreover, the Uruguay Round Agricultural Negotiation would prohibit government price support for agricultural products. In October the Korean government decides the government purchase amount and support price, which works as the price guideline. All interested parties exert political efforts to influence the decision. The continued increase of the government purchase price of rice due to political pressure pushed the government purchase price above the market wholesale price in 1988. Also, the farmers preferred to sell to the government than to the wholesaler. This has discouraged the market mechanism, and the government is to take over the three functions of the market mechanism: stockpiling, seasonal price fluctuation adjustment, and circulation. Another big increase may cause the government purchase price to rise above the consumer price, which might lead to arbitrage opportunities for the farmers and suffocate the market mechanism. However, the current political situations limits the options for the Korean government. This paper argues that a supply control policy will reduce the social cost resulting from the high level of producer price support, and it proposes several second best policies: First, the production of new varieties should be reduced rapidly. Second, the old rice in the government warehouse should be auctioned or disposed of in order to reduce the government handling and management costs. Third, the acreage diversion program should be launched in order to control rice paddy acreage. Fourth, a social welfare program in rural areas should be introduced, since the share of population over 60 is increasing rapidly. Fifth, instead of the price support which is forbidden by the Uruguay Round, Korea should restructure the agricultural industry by developing new crops, by enhancing productivity and by improving the agricultural infrastructure.

• Journal of the Korean Society of Radiology
• /
• v.11 no.3
• /
• pp.139-146
• /
• 2017

At the Brain MRI examination, RF Pulse are irradiated on the human head in order to acquire MR images. At this time, a considerable part of the irradiated RF Pulse energy is absorbed in our body and the temperature of the human head will rise depending on the degree of exposure, so it will affect the human head. Even if the same RF Pulse energy is given, if the metal is inserted in the human head, the conductivity of the human head is greatly increased by the metal, so the SAR value increases and the temperature also rises. Therefore, we started this research with the question as to whether there is difference between the change in SAR value and temperature displayed on the head of the human according to use or not of the dental implant. Experiments were using the XFDTD program on a 128 MHz RF Pulse frequency by a 3.0 tesla MRI. We can see that both are increasing that the average value of SAR and temperature that absorbed by the human head model used the dental implant. In addition, the average maximum SAR value and the maximum temperature rise in the brain part are shown below the international safety standard value but the influence can not be ignored because of the result may change according to the increase in the number of dental implant. And as future tasks. we need to the simulation of temperature rise and SAR due to an increase in the number of implants and volumes of teeth, dental implant material.