• Journal of the Korean Vacuum Society
• /
• v.15 no.3
• /
• pp.314-324
• /
• 2006

The vacuum characteristics of the KSTAR ICRF antenna were experimentally investigated. The fabricated antenna was installed in the RF Test Chamber(RFTC) which has a vacuum system with an effective pumping speed of 1015 l/s. The time variations of RFTC pressure, total gas load and ultimate pressure were measured before the RF test. RF conditioning effect was studied by repeating RF pulses at low power level. A time variation of the RFTC pressure was measured during a RF power was applied to the antenna. Threshold pressure at which a RF breakdown occurs was investigated. Whenever the pressure was higher than $10^{-4}$ mbar, the RF breakdown occurred. During a long pulse testing, the temperature of the antenna and RFTC pressure were measured to investigate long pulse limitation of the maximum available voltage without any cooling, which were compared with testing results with a water cooling of the antenna.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.3
• /
• pp.1-7
• /
• 1999

A single RF transceiver evaluation board have been developed for the purpose of application to the 900MHz band transceiver contained RF-IC chip And environment test was evaluated. The RF-IC chipset includes LNA(Low Noise Amplifier), down-conversion mixer, AGC(Automatic Gain Controller), switched capacitor filter and down sampling mixer. The RF evaluation board for the testing of chipset contained various external matching circuits, filters such as RF/IF SAW(Surface Acoustic Wave) filter and duplexer and power supply circuits. With the range of 2.7~3.3V the operated chip revealed moderate power consumption of 42mA. The chip was well operated at the receiving frequency of 925~960MHz. Measurement result is similar to general RF receiving specification of the 900MHz digital mobile phone.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.818-823
• /
• 2003

본 논문에서는 입력 매칭(input matching) BIST(Built-In Self-Test) 회로를 이용한 RF font end의 새로운 결함 검사방법을 제안한다. BIST 회로를 가진 RF front end는 1.8GHz LNA(Low Noise Amplifier: 저 잡음 증폭기)와 이중 대칭 구조의 Gilbert 셀 믹서로 구성되어 있으며, TSMC 0.25$\mu\textrm{m}$ CMOS 기술을 이용하여 설계되었다. catastrophic 결함 및 parametric 변동을 가진 RF front end와 결함을 갖지 않은 RF front end를 판별하기 위해 RF front end의 입력 전압 특성을 조사하였다. 본 방법에서는 DUT(Device Under Test: 검사대상이 되는 소자)와 BIST 회로가 동일한 칩 상에 설계되어 있기 때문에 측정할 때 단지 디지털 전자계와 고주파 전압 발생기만이 필요하며, 측정이 간단하고 비용이 저렴하다는 장점이 있다. BIST 회로가 차지하는 면적은 RF front end가 차지하는 전체면적의 약 10%에 불과하다. 본 논문에서 제안하는 검사기술을 이용하여 시뮬레이션해 본 결과 catastrophic 결함에 대해서는 100%, parametric 변동에 대해서는 약 79%의 결함을 검출할 수 있었다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.1
• /
• pp.45-52
• /
• 2003

A number of stress corrosion cracks in turbine rotor disk keyway in power plants have been found and the necessity has been raised to detect and evaluate the cracks prior to the catastrophic failure of turbine disk. By ultrasonic RF signal analysis and using a neural network based on bark-propagation algorithm, we tried to evaluate the location, size and orientation of cracks around keyway. Because RF signals received from each reflector have a number of peaks, they were processed to have a single peak for each reflector. Using the processed RF signals, scan data that contain the information on the position of transducer and the arrival time of reflected waves from each reflector were obtained. The time difference between each reflector and the position of transducer extracted from the scan data were then applied to the back-propagation neural network. As a result, the neural network was found useful to evaluate the location, size and orientation of cracks initiated from keyway.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.23 no.1
• /
• pp.112-122
• /
• 2024

Recently, as unmanned aerial vehicle technology such as drones has developed, there are many environmental, social and economic benefits, but if there is malicious intent against important national facilities such as airports, public institutions, power plants, and the military, it can seriously affect national safety and people's lives. It can cause damage. To respond to these drone threats, attempts are being made to introduce detection equipment such as RF scanners. In particular, power transmission towers installed in substations, power plants, and Korea's power system can affect detection performance if the transmission tower is located in the RF scanner detection path. In the experiment, a commercial drone was used to measure the signal intensity emitted from the drone and confirm the attenuation rate. The average and maximum attenuation rates showed similar trends in the 2.4 GHz and 5.8 GHz bands, and were also affected by the density of the structure.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.540-543
• /
• 2003

This paper presents design and manufacture of RF type non-contact radiological dosage measuring device. It also concerns on the broad out-line and the ways of improvement about RF type non-contact radiation measuring device. Measuring radiological dosage with non-contact RF, the stability and efficiency of the measure have been improved by reforming constant current circuit. Furthermore, applying communication protocol in process makes it possible to achieve faster and more accurate communication than old circuit. On the base of those, RF type non-contact radiological dosage measuring device which consists of radiological dosage measuring module and Reader module has been designed and manufactured. While testing communication against embodied device, the possibility of the field application could be confirmed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.5
• /
• pp.416-420
• /
• 2008

In EMAT field, spiral RF coils are much more widely used when compared with solenoid coils. In the field of the magnetostrictive strip transducers for long range ultrasonic testing of cylindrical structures, however, solenoid coils has been used. This seems to be attributed to the difficulty in fabricating low frequency (i.e., large size) spiral coils. In this paper, we describe a method for fabricating spiral coil magnetostrictive strip guided wave transducers from FFC (flexible flat cable). It is demonstrated through a comparison experiment that the spiral coil transducer has much superior performance (sensitivity, SNR, and guided wave direction control capability) than the previous transducer with solenoid coils.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.6
• /
• pp.635-644
• /
• 2003

To ensure the reliability of ultrasonic nondestructive testing techniques for modern structural materials, the effects of anisotropy and inhomogeneity and the influence of non-planar component geometries on ultrasonic wave propagation have to be taken into account. In this article, fundamentals and applications of two analytical approaches to three-dimensional elastic beam field calculation are presented. Results for both isotropic materials including curved interfaces and for anisotropic media like composites are presented, covering field profiles for various types of transducers and the modeling of time-dependent rf-signals.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.6
• /
• pp.927-934
• /
• 1999

A measuring system was integrated for the testing of live EED with continuous wave RF stimulus at low frequency range(1~250 MHz) and pulsed RF stimulus at high frequency range(8~10 GHz). The test system, set-up method and test procedure for the RF sensitivity of EED are described in this paper. The Bruceton method is applied to obtain distribution statistics such as mean firing level, standard deviation of the distribution and confidence levels for various applied firing signals.

• Journal of Digital Contents Society
• /
• v.13 no.4
• /
• pp.491-500
• /
• 2012

In this paper, a new loopback BIST structure which is effective to test RF transceiver chip and LNA(Low Noise Amplifier) in the chip is presented. Because the presented BIST structure uses a baseband processor in the chip as a tester while the system is under testing mode, the developed test technique has an advantage of performing test application and test evaluation in effectiveness. The presented BIST structure can change high frequency test output signals to a low frequency signals which can make the CUT(circuits under test) tested easily. By using this technique, the necessity of RF test equipment can be mostly reduced. The test time and test cost of RF circuits can be cut down by using proposed BIST structure, and finally the total chip manufacturing costs can be reduced.